利用分形几何确定多孔介质的孔尺寸分布

提出了利用分形几何确定多孔介质孔尺寸分布的方法。考虑多孔介质中孔间的屏蔽，采用此方法得到的孔尺寸分布范围比采用平行孔模型宽，分别采用本方法和平行孔模型测定γ－Al2O3催化剂的孔尺寸分布，构造简单立方体三维网络模型模拟压汞过程，并将模拟曲线与γ－Al2O3压汞实验曲线比较，结果表明，采用本方法所得孔尺雨分布优于平行孔模型所得孔尺寸分布。     

浅谈监理工程师如何抓好施工阶段的投资控制

在多年工程实践的基础上研究、分析了施工阶段投资控制的方法问题。     

电镀锡机组软熔导电辊脱锡技术研究

粘锡是电镀锡机组软熔导电辊失效的主要原因,应用化学方法脱锡是延长导电辊寿命的重要途径.开发了氢氧化钠(钾)为主要组成,并加入适量亚铅酸钠(钾)和硝酸(亚硝酸)钠配制而成脱锡剂,当脱锡剂温度为40～80℃,导电辊表面温度为40～70℃时,对粘锡导电辊具有很好的脱锡效果.粘锡导电辊脱锡后的表面粗糙度可以恢复到4.0μm以上,导电辊使用寿命提高80%,降低导电辊修复成本90%,并大幅度减少导电辊更换时间,提高电镀锡机组生产作业率.     

活性碳和5A分子筛的吸附特性及其在真空获得中的作用

评述了活性碳和５Ａ分子筛的吸附等温线及其在真空佩温绝热夹层真空获得中的作用。分析了真空夹层抽真空除气时用Ｎ＿２气置换以及用“多次吸附－脱附Ｎ＿２气”方法活化吸附剂等先进工艺的机理。论述了根据吸附剂吸水的吸附等温线，合理确定活化工艺条件的方法。     

高炉炉缸内铁水环流与内衬侵蚀

从分析中心焦柱在炉缸内的受力出发，计算了１０００￣５５８０ｍ＾３高炉大喷煤前后中心焦柱在炉缸铁水内的沉入深度，分析了炉缸内铁水环流的产生与炉缸内衬侵的关系，分析表明大喷煤有得利抑制铁水环流对缸内补的冲刷，提出了降低铁水环流对炉缸内衬侵蚀的途径。     

一种微机控制的多测头凸轮轴测量系统

本文介绍一种由机械装置，高精度圆光栅编码器，光栅位移传感器，微型计算机，接口控制电路等组成的多测头凸轮轴测量系统，该系统安装调整方便，定位准确，测量精度高，操作简单，工作可靠，能快速实现对凸轮轴的自动测量。     

Study on percutaneous rate of P-aminobenzoates using molecular orbital method

The use of a dome osteotomy in the treatment of infantile tibia vara is reportedly associated with insufficient intraoperative assessment of the correction achieved. This article discusses a method to overcome this problem and the long-term advantages of using a dome osteotomy in the treatment of this disease.     

SURF1, encoding a factor involved in the biogenesis of cytochrome c oxidase, is mutated in Leigh syndrome

A drug with cationic characteristics such as procaine can be conveyed in a Carbomer hydrogel in two different ways: (i) in the form of salt in solution in the aqueous phase, and (ii) in the base form salified with the same polymer. Introduction of the drug into the hydrogel with different concentrations of polymer produced, in both cases, a reduction in viscosity in relation to drug concentration. The gels with procaine salified with the polymer showed greater viscosity. The drug release rate, in general, diminished with the increase in polymer concentration. Nevertheless, when this concentration was maintained, there was no variation in release rate when the viscosity produced as a consequence of drug concentration was changed. Gels with procaine salified with the carboxyvinylic polymer had a faster release rate than those with procaine in the hydrochloride form dissolved in the aqueous phase. These results have also been confirmed by a simulated absorption test.     

动态交联热塑性弹性体增韧聚丙烯合金

用动态交联方法制备聚烯烃热塑性弹性体（ＴＰＯ）增韧聚丙烯，制备了具有低温冲击性能良好、综合力学性能比较均衡的聚丙烯合金。同时，研究了ＴＰＯ组成、工艺及基体组成与ＴＰＯ增韧聚丙烯共混物力学性能的关系。并通过差热扫描量热计和扫描电镜考察了共混物的形态结构。     

Determination of the in situ forces and force distribution within the human anterior cruciate ligament

The in situ forces and their distribution within the human anterior cruciate ligament (ACL) can clarify this ligament's role in the knee and help to resolve controversies regarding surgical treatment of ACL deficiency. We used a universal force-moment sensor (UFS) to determine the magnitude, direction, and point of application of the in situ forces in the ACL in intact human cadaveric knees. Unlike previous studies, this approach does not require surgical intervention, the attachment of mechanical devices to or near the ACL, or a priori assumptions about the direction of in situ force. Anterior tibial loads were applied to intact knees, which were limited to 1 degree of freedom at 30 degrees flexion. The in situ forces developed in the ACL were lower than the applied force for loads under 80 N, but larger for applied loads of more than 80 N. The direction of the force vector corresponded to that of the anteromedial (AM) portion of the ACL insertion on the tibial plateau. The point of force application was located in the posterior section of the anteromedial portion of the tibial insertion site. The anterior and posterior aspects of the anteromedial portion of the ACL supported 25% and 70% of the in situ force, respectively, with the remainder carried by the posterolateral portion. We believe that the data obtained with this new UFS methodology improves our understanding of the role of the ACL in knee function, and that this methodology can be easily extended to study the function of other ligaments.