温度梯度机理下激光参数对激光成形的影响

以纯铝板和低碳钢板为主要研究对象，对温度梯度机理下激光输入功率、扫描速度、离焦量以及扫描次数等参数与成形弯曲角之间的关系进行了试验研究，深入分析了温度梯度机理下影响成形的主要因素。     

Magnetic properties and microstructural characteristics of bulk Nd–Al–Fe–Co glassy alloys

Bulk Nd–Al–Fe–Co glassy alloys with diameter up to 5 mm were investigated by magnetic measurements, magnetic force microscopy (MFM) and high resolution electron microscopy (HREM) at room temperature. The results from the measurement of vibrating sample magnetometer show that these samples with compositions Nd₆₅Al₁₀Fe_25-xCo_x (x=0–10 at.%) and Nd₆₀Al₁₀Fe₂₀Co₁₀ display hard magnetic properties with H_C of 300 kAm⁻¹, M_S of 10 Am² kg⁻¹, and M_r of 7 Am² kg⁻¹. The MFM measurements of the Nd₆₀Al₁₀Fe₂₀Co₁₀ bulk metallic glass (BMG) reveal the existence of magnetic domains with a period of about 0.36 μm, and the ordered clusters with the averaged size of about 5 nm was observed by the HREM on the sample. The domain structure or cluster is believed to be associated with the appearance of hard-magnetic properties in this alloy system. The existence of the large-size domains demonstrates that magnetic moment of a great deal of ordered atomic clusters in the BMG has been aligned by exchange-coupling.     

触觉式机器人焊缝跟踪方法

对机器人在焊缝自动跟踪方面进行了研究，介绍了机器人触觉的力传感器结构和使用方法。对力信号进行解耦及信号解算，有效地消除了机器人在工作过程中振动，抖动对力信号的污染，使机器人有能力自动识别，跟踪焊缝及焊枪位置修正，从而保证焊接质量。     

Novel technology of purification of copper electrolyte

The effects of arsenic with different valence states on the purification of copper electrolyte were studied and a novel technology of purification of copper electrolyte by copper arsenite was proposed. The results show that the purification performance of As（Ⅲ） compounds is better than that of As（Ⅴ） compounds. The purification technology by copper arsenite has the advantages of simple operation, high purification performance and low cost in comparison with other technologies and its appropriate purification conditions are that copper arsenite concentration is 18 g/L, reaction temperature is 65 ℃ and reaction time is 8 h. The removal rates of Sb and Bi are 53.22% and 58.67% respectively under these conditions. The purification principle show that a kind of yellow precipitate mainly composed of arsenic, antimony （ Ⅴ ）, bismuth and oxygen forms in electrolyte after copper arsenite is added, and consequently antimony and bismuth are removed from electrolyte.     

熔体处理对一种Inconel 718C改型高温合金组织与性能的影响

在试验合金中,1600℃熔体处理对凝固后组织和性能产生显著影响。经1600℃熔体处理后,合金样品二次枝晶间距显著降低,元素偏析情况得到有效改善,凝固过程析出的TCP相数量明显减少,热处理后γ″析出相也更加细小均匀。熔体处理对合金室温和700℃拉伸强度影响不大,但却显著提高合金的拉伸塑性和700℃/620MPa持久性能。在1600℃熔体处理10min时,合金的综合力学性能最佳;延长熔体处理时间至15min时,合金力学性能呈下降趋势。     

180kA大型铝电解槽力场测试与分析

阐述了１８０ｋＡ大型铝电解槽槽壳的位移现场测试手段、槽壳表面位移特征和槽壳所受内力的计算方法，并对槽壳结构优化设计做了分析     

电流密度对声电沉积生物活性透钙磷石涂层结构和形貌的影响

通过声电沉积工艺在碳／碳复合材料表面制备了生物活性透钙磷石涂层，采用SEM、FFIR、XRD研究了超声场中电流密度对涂层组成结构和形貌的影响。发现在一定工艺条件下，随电流密度增加，涂层的平均晶粒尺寸减小，致密度增加；当电流密度小于l0mA／cm^2时涂层形貌为片状，l0mA／cm^2-26mA／cm^2时为粒状，32mA／cm^2时为花菜心状。且涂层中透钙磷石晶体的择优取向也发生变化，择优晶面依次为(021)、(111)、(220)。同时还讨论了涂层微观结构变化机理。     

Hydriding-dehydriding properties of Mg2Ni alloy modified by ball-milling in tetrahydrofuran

A new approach of ball-milled Mg2Ni in tetrahydrofuran (THF) to improve the hydriding kinetics of Mg2Ni alloy is suggested and studied. It is found that the modified alloy displayed the improved activity for hydriding even at relatively low temperature (e.g., 323-373 K). In the case of the sample milled in THF for 20 h, the hydrogen content (mass fraction) reaches 1.6 % at 323 K, 2.1% at 348 K and 3.4% at 448 K, respectively. The use of THF during grinding led to the change of the structure, which is reflected by the broadening and weakening of the diffraction peaks in the XRD spectra. The XPS analysis shows that Mg (2s) binding energy peak of Mg2Ni after modification shifted from a lower binding energy to a higher one, indicating the charge transference between Mg and THF and the formation of catalytically active electron donor-acceptor (EDA) complexes on the surface of modified Mg2Ni alloy.     

梯度功能材料研究的一些进展

综述了近年来梯度功能材料(FGM)在优化设计、制备、性能评价以及应用方面的最新研究进展，并对其中的热点问题作了系统阐述。对于热应力缓和型FGM，其优化设计的关键环节是准确分析残余热应力的大小和分布。液相法制备FGM以其低成本、操作简单的优势将会获得更大的发展。对FGM的性能测试要尽可能模拟实际使用环境下载荷的不均匀分布。梯度功能热障涂层是FGM的重要应用之一，它与传统的热障涂层相比可明显提高耐久性。此外，还介绍了FGM在面向等离子体护墙材料以及生物材料上的应用。     

16MnR钢高压除氧器焊接接头裂纹的成因

本文采用电镜，Ｘ射线衍射分析、裂纹扩展速率ｄａ／ｄＮ及门槛值△Ｋｔｈ试验，研究了火力发电厂１６ＭｎＲ钢高压除氧器焊接接头裂纹的形成原因，结果表明，原发裂纹为延迟裂纹，运行工况下，裂纹以应力腐蚀裂纹方式扩展。