Morphology and mechanical properties of liquid crystalline copolyester and poly(ethylene 2,6-naphthalate) blends

Blends of poly(ethylene 2,6-naphthalate) (PEN) and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate), were prepared in a twin-screw extruder. Specimens for mechanical testing were prepared by injection molding. The morphology and mechanical properties were investigated by scanning electron microscopy (SEM) and an Instron tensile tester. SEM studies revealed that finely dispersed spherical domains of the liquid crystalline polymer (LCP) were formed in the PEN matrix, and the inclusions were deformed into fibrils from the spherical droplets with increasing LCP content. The morphology of the blends was found to be affected by their composition and a distinct skin-core morphology was found to develop in the injection molded samples of these blends. Mechanical properties were improved with increasing LCP content, and synergistic effects have been observed at 70 wt% LCP content whereas the elongation at break was found to be reduced drastically above 10 wt% of LCP content. This is a characteristic typical of chopped-fiber-filled composites. The improvement in mechanical properties is likely due to the reinforcement of the PEN matrix by the fibrous LCP phase as observed by scanning electron microscopy. The tensile and modulus mechanical behavior of the LCP/PEN blends was very similar to those of the polymeric composite, and the tensile strength and flexural modulus of the LCP/PEN 70/30 blend were two times the value of PEN homopolymer and exceeded those of pure LCP, suggesting LCP acts as a reinforcing agent in the blends.     

Enhancement of combustion efficiency with mixing ratio during fluidized bed combustion of anthracite and bituminous blended coal

In order to investigate the effect of mixing ratio of bituminous coal to blended coal on the enhancement of combustion efficiency, combustion experiments of blended coal with anthracite and bituminous are done in a laboratory scale fluidized bed combustor (10.8 cm ID and 170 cm height). The gross heating values of anthracite and bituminous coal used in this study are 2,810 cal/g and 6,572 cal/g, respectively. Experimental parameters are fuel feed rate, superficial gas velocity and mixing ratio of bituminous coal to blended coal. The combustion efficiency increases with the mixing ratio of bituminous coal due to the lower unburned carbon losses and higher burning velocity of bituminous coal. The rate of combustion in the combustor was increased with mixing ratio resulted from a higher burning velocity of bituminous coal. The measured combustion efficiency experimentally is about 3.5-12.4% higher than that of the calculated value based on the individual combustion of anthracite and bituminous coal under the same operating conditions. The optimum mixing ratio (MR) of bituminous coal determined is around 0.75 in this study. This paper is dedicated to Professor Dong Sup Doh on the occasion of his retirement from Korea University.     

Organic Nanoparticles with Polypropyleneoxide Chains as Support for Metallocene Catalysts: Ethylene Homopolymerization and Ethylene/α-olefin Copolymerization

Summary Novel organic nanoparticles functionalized with nucleophilic polypropyleneoxide (PPO) chains on their surfaces for supporting metallocene catalysts in heterogeneous olefin polymerization are presented. The nanoparticles (60–100 nm) were obtained by miniemulsion polymerization of styrene, divinylbenzene and PPO functionalized styrene. It is demonstrated that Me₂Si(2MeBenzlnd)₂ZrCl₂/MAO supported on these nanoparticles is suitable for the homopolymerization of ethylene, resulting in excellent product morphologies and high activities. lt is shown that by varying the MAO/Zr ratios and Zr concentrations the activities and productivities of the catalysts as well as the qualities of the polyethylene products can be tuned. These new supported catalysts are also suitable for the copolymerization of ethylene with several comonomers (1-hexene, 1-octene, 1-decene or norbornene). As the obtained product properties like crystallinity, melting temperature or bulk density match the results of silica supported systems, these organic nanoparticles can be considered as alternative carriers in comparison to the established inorganic ones.     

Pathline glyphs

Visualization of pathlines is common and highly relevant for the analysis of unsteady flow. However, pathlines can intersect, leading to visual clutter and perceptual issues. This makes it intrinsically difficult to provide expressive visualizations of the entire domain by an arrangement of multiple pathlines, in contrast to well‐established streamline placement techniques. We present an approach to reduce these problems. It is inspired by glyph‐based visualization and small multiples: we partition the domain into cells, each corresponding to a downscaled version of the entire domain. Inside these cells, a single downscaled pathline is drawn. On the overview scale, our pathline glyphs lead to emergent visual patterns that provide insight into time‐dependent flow behavior. Zooming‐in allows us to analyze individual pathlines in detail and compare neighboring lines. The overall approach is complemented with a context‐preserving zoom lens and interactive pathline‐based exploration. While we primarily target the visualization of 2D flow, we also address the extension to 3D. Our evaluation includes several examples, comparison to other flow visualization techniques, and a user study with domain experts.     

Conceptual and basic designs of the Mobile Harbor crane based on topology and shape optimization

The Mobile Harbor (MH) has been recently proposed as a novel maritime cargo transfer system that can move to a container ship anchored in the deep sea and handle containers directly at sea with the aid of a stabilized MH crane. Because this system operates under at-sea conditions, the MH crane must be designed to support an inertia load and wind force, as well as its self-weight. The wave-induced motions of the MH, e.g. rolling, pitching, and heaving, generate a significant amount of inertia load, which has not been considered in the design of conventional quayside cranes installed on stable ground. Wind force is also a critical design factor due to the higher wind velocity in the open sea. In addition to the aforementioned structural rigidity, mass minimization is also important in the structural design of MH cranes because it reduces the overturning moment and therefore enhances ship stability. In this paper, the sensitivities of the design-dependent loads (i.e. self-weight, inertia load, and wind force) are derived with respect to the design variables, and then a topology optimization is conducted with the derived sensitivities in order to obtain a conceptual design. Then, the conceptual design is elaborated into a three-dimensional basic design through shape optimization with design regulations for offshore cranes. Through the integrated design process with the topology and shape optimizations, a conceptual and basic design is successfully obtained for the MH crane.     

Cure kinetics of high performance epoxy resin systems

Summary Isothermal cure kinetics ofEPON HPT 1071/DDS system have been performed by means of differential scanning calorimetry. The maximum cure rate and the extent of conversion at various DDS concentrations were studied as a function of cure temperature. Maximum cure rate increases with increasing cure temperature and DDS concentration. At various DDS concentrations, the maximum cure rate occured between 19–22% conversion. In order to evaluate the kinetic parameters, numerical calculations by means of a Newton-Raphson technique and experimental results obtained from the peak of reaction rate curve were undertaken.     

The removal of hydrogen sulfide with manganic sorbent in a high-temperature fluidized-bed reactor

The removal of hydrogen sulfide (H₂S) from simulated gas was carried out in a batch type fluidized-bed reactor using natural manganese ore (NMO), which consists of several metal oxides (MnO_x: 51.85%, FeO_y: 3.86%, CaO: 0.11%). The H₂S breakthrough curves were obtained by changing temperature, gas velocity, initial H₂S concentration, and aspect ratio. Moreover, the effects of the particle size and the particle-mixing fraction on H₂S removal were investigated in a binary system of different particle size. From this study, H₂S removal efficiency increased with increasing temperature but decreased with increasing excess gas velocity. The breakthrough time for H₂S decreased as the gas velocity increased, which leads to reducing gas-solid contacting due to gas bypassing in a fluidized bed reactor. Improvement of H₂S removal efficiency in continuous process can be expected from the results of the binary particle system with different size in a batch experiment. The NMO could be considered as a potential sorbent in H₂S removal.     

Synthesis and physicochemical characterization of amphiphilic block copolymer self‐aggregates formed by poly(ethylene glycol)‐block‐poly(ϵ‐caprolactone)

Diblock copolymers with different poly(ε‐caprolactone) (PCL) block lengths were synthesized by ring‐opening polymerization of ε‐caprolactone in the presence of monomethoxy poly(ethylene glycol) (mPEG‐OH, MW 2000) as initiator. The self‐aggregation behaviors and microscopic characteristics of the diblock copolymer self‐aggregates, prepared by the diafiltration method, were investigated by using ¹H NMR, dynamic light scattering (DLS), and fluorescence spectroscopy. The PEG–PCL block copolymers formed the self‐aggregate in an aqueous environment by intra‐ and/or intermolecular association between hydrophobic PCL chains. The critical aggregation concentrations of the block copolymer self‐aggregate became lower with increasing hydrophobic PCL block length. On the other hand, reverse trends of mean hydrodynamic diameters were measured by DLS owing to the increasing bulkiness of the hydrophobic chains and hydrophobic interaction between the PCL microdomains. The partition equilibrium constants (K_v) of pyrene, measured by fluorescence spectroscopy, revealed that the inner core hydrophobicity of the nanoparticles increased with increasing PCL chain length. The aggregation number of PCL chain per one hydrophobic microdomain, investigated by the fluorescence quenching method using cetylpyridinium chloride as a quencher, revealed that 4–20 block copolymer chains were needed to form a hydrophobic microdomain, depending on PCL block length. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3520–3527, 2006     

Sulfonated polyimide and poly (ethylene glycol) diacrylate based semi‐interpenetrating polymer network membranes for fuel cells

Semi‐interpenetrating polymer network (semi‐IPN) membranes based on novel sulfonated polyimide (SPI) and poly (ethylene glycol) diacrylate (PEGDA) have been prepared for the fuel cell applications. SPI was synthesized from 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl 2,2′‐disulfonic acid, and 2‐bis [4‐(4‐aminophenoxy) phenyl] hexafluoropropane. PEGDA was polymerized in the presence of SPI to synthesize semi‐IPN membranes of different ionic contents. These membranes were characterized by determining, ion exchange capacity, water uptake, water stability, proton conductivity, and thermal stability. The proton conductivity of the membranes increased with increasing PEGDA content in the order of 10^?1 S cm^?1 at 90°C. These interpenetrating network membranes showed higher water stability than the pure acid polyimide membrane. This study shows that semi‐IPN SPI membranes based on PEGDA which gives hydrophilic group and structural stability can be available candidates comparable to Nafion® 117 over 70°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and characterization of maleic anhydride‐g‐polypropylene/diamine‐modified clay nanocomposites

Polypropylene (PP)/montmorillonite (MMT) nanocomposites were prepared by compounding maleic anhydride‐g‐polypropylene (MAPP) with MMT modified with α,ω‐diaminododecane. Structural characterization confirmed the formation of characteristic amide linkages and the intercalation of MAPP between the silicate layers. In particular, X‐ray diffraction patterns of the modified clay and MAPP/MMT composites showed 001 basal spacing enlargement as much as 1.49 nm. Thermogravimetric analysis revealed that the thermal decomposition of the composite took place at a slightly higher temperature than that of MAPP. The heat of fusion of the MAPP phase decreased, indicating that the crystallization of MAPP was suppressed by the clay layers. PP/MAPP/MMT composites showed a 20–35% higher tensile modulus and tensile strength compared to those corresponding to PP/MAPP. However, the elongation at break decreased drastically, even when the content of MMT was as low as 1.25–5 wt %. The relatively short chain length and loop structure of MAPP bound to the clay layers made the penetration of MAPP molecules into the PP homopolymer phase implausible and is thought to be responsible for the decreased elongation at break. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 307–311, 2005