Interfacial shear strength of C/C composites

Fiber-bundle push-out, single-fiber push-in, and single-fiber push-out tests were conducted in order to examine the applicability of these methods for determining the interfacial shear strength of carbon-carbon composites. The fiber-bundle push-out test resulted mostly in fractures along the fiber/matrix interface but created a small amount of fractures in the matrix. Hence, the evaluated strength was regarded as an approximate value. In order to precisely evaluate the interfacial strength, push-in and push-out tests for a single fiber were performed using a micro-Vickers indentation tester. In these tests, the load has to be placed within a target fiber, and the indentation should not extend to the matrix. This condition restricted the load that could be applied to a carbon fiber. Within this limit, a single carbon fiber could not be pushed-in. For the sake of load reduction, single-fiber push-out tests were conducted using thin specimens. The thickness appropriate for a single-fiber push-out specimen was estimated based on the interfacial shear strength obtained by the bundle push-out tests. Below this thickness, single-fiber push-out tests could be successfully performed.     

Evidence for the formation of interpenetrated spherulites in poly(butylene succinate-co-butylene carbonate)/poly(l-lactic acid) blends investigated by atomic force microscopy

The spherulitic morphology in poly(butylene succinate-co-butylene carbonate)/poly(l-lactic acid) (PEC/PLLA) blends was investigated by atomic force microscopy (AFM) to obtain direct evidence for the formation of interpenetrated spherulites (IPS), where the spherulites of PEC penetrate into PLLA spherulites. The observation actually revealed that PEC crystals penetrated into interfibrillar regions of edge-on lamellae in a PLLA spherulite. The penetration process was also investigated by AFM with a temperature controller. An edge-on PLLA lamella or a fibril that ran nearly perpendicular to the growth direction of a PEC spherulite obstructed the growth of PEC spherulite. The PEC crystals filled the blocked space after growing around the PLLA lamella. These results showed that the spherulites of PEC and PLLA grow on the same layer instead of forming a layered structure of two spherulites. All the results supported the formation of IPS.     

Role of network nematicity in swelling and phase equilibria of polymer networks in nematic solvents

Swelling and phase equilibria of polymer networks in a low molecular mass liquid crystal (LC) have been investigated as a function of network nematicity. LC networks with varying nematicity were prepared by copolymerization of mixtures of mesogenic monomers and non-mesomorphic (styrene) monomers with various compositions. Molar fraction of mesogenic monomer (x) in copolymer network strongly influences the swelling behavior as well as the nematic-isotropic (N-I) transitions in both dry and swollen states. The swollen networks of sufficiently high x with strong nematicity exhibit a sharp N-I transition and simultaneously undergo a discontinuous change in gel volume, i.e. volume phase transition. Meanwhile, the swollen networks of x≤0.8 with less nematicity show a broad N-I transition, and the resulting volume change proceeds continuously over a finite temperature range. When x decreases further down to less than 0.5, the nematicity of the dry networks vanishes. The nematic ordering in the swollen copolymer networks of x<0.5 occurs at the same temperature as the N-I transition temperature of the pure nematic solvent (T_NI^S), which yields the inflection in the swelling-temperature curve. A mean field theory considering network nematicity as a variable describes the effects of x on volume phase transition such as a shift of T_NI^G and a change in the magnitude of volume transition, apart from the emergence of continuous volume transition due to the broad N-I transition. The purely isotropic network of x=0 appreciably swells in the nematic solvent. The solvent inside the gel forms the nematic phase at the temperatures below which conflicts with the classical theoretical prediction that nematic ordering of LC solvent in fully swollen isotropic network never occurs.     

Fabrication of three‐dimensionally ordered microporous membrane by wet phase separation

We report a novel porous fluorinated polyimide membrane with a cylinder structure fabricated by a wet phase inversion process, which is formed by a ternary system, polyimide/solvent/water. The porous polyimide membranes consisted of a thin top porous layer and three‐dimensionally ordered cylinder micropores. The porous membrane‐forming solvents were N‐methylpyrrolidone containing nonsolvent additives such as alcohol, and the height and width of the cylinder structure were controlled by the solvents. Water fluxes through the porous polyimide membranes were measured using a stirred dead‐end filtration cell, and the fluxes of the porous membrane with the cylinder‐type structure were approximately three times greater than those of the membrane with the finger‐type structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3016–3021, 2004     

Power characteristics of unsteadily forward–reverse rotating impellers in an unbaffled aerated agitated vessel

Power characteristics of an unbaffled aerated agitated vessel with unsteadily forward‐reverse rotating impellers, ie a new type of gas–liquid agitator named ‘AJITER’, treating viscous Newtonian liquids were studied experimentally. Measurements were first made on the agitation torque, ie the torque on the drive shaft on which forward–reverse rotating impellers with four delta‐type blades were attached, and the data obtained were analyzed by fitting them to an equation consisting of two terms with respect to the resistance of the fluid, one due to viscous drag and the other due to added moment of inertia. The effects of operating conditions and physical properties of liquids on the drag and added moment of inertia coefficients were then evaluated, and empirical relationships which estimate values of these coefficients, useful to predict the unsteady behavior and magnitude of agitation torque, were presented. Furthermore, equations were developed for estimating the average and maximum power consumptions as a function of the drag and added moment of inertia coefficients. Prediction of respective power levels in AJITER by these equations was also discussed. © 2001 Society of Chemical Industry     

Structurally Diverse Polyamines: Solid‐Phase Synthesis and Interaction with DNA

A versatile solid‐phase approach based on peptide chemistry was used to construct four classes of structurally diverse polyamines with modified backbones: linear, partially constrained, branched, and cyclic. Their effects on DNA duplex stability and structure were examined. The polyamines showed distinct activities, thus highlighting the importance of polyamine backbone structure. Interestingly, the rank order of polyamine ability for DNA compaction was different to that for their effects on circular dichroism and melting temperature, thus indicating that these polyamines have distinct effects on secondary and higher‐order structures of DNA.     

Nickel‐Catalyzed Suzuki–Miyaura Coupling of a Tertiary Iodocyclopropane with Wide Boronic Acid Substrate Scope: Coupling Reaction Outcome Depends on Radical Species Stability

We describe a nickel‐catalyzed Suzuki–Miyaura arylation of a tertiary iodocyclopropane with arylboronic acids; this is an efficient and convergent strategy for providing various enantioenriched arylcyclopropanes with a quaternary stereogenic center. This is the first metal‐catalyzed coupling between a tertiary alkyl electrophile and a wide range of aromatics, including heteroaromatics. We found that the outcome of the Ni‐catalyzed coupling with halides as electrophiles was dependent on the stability of the radical species formed during the reaction. The use of tert‐butyl alcohol (t‐BuOH) as the reaction solvent was very effective, because of its stability under the radical‐generating reaction conditions.

     

Synthesis of geranyl acetate by lipase entrap-immobilized in cellulose acetate-TiO2 gel fiber

Lipase from Candida antarctica was entrap-immobilized in cellulose acetate-TiO₂ gel fiber (fiber-immobilized lipase) by the sol-gel method. Syntheses of geranyl acetate and citronellyl acetate catalyzed by the fiber-immobilized lipase were studied in heptane solution. Conversions reached 85% for geranyl acetate after 100 h, and 75% for citronellyl acetate after 80 h, and these values were almost identical to those for syntheses catalyzed by nonimmobilized lipase, although the reaction rate was decreased by immobilization. Compared to those of the non-immobilized lipase and commercially available immobilized lipase (Novozyme 435), the activity of the fiber-immobilized lipase was not particularly affected by changes in reaction conditions, such as bulk water content or substrate concentration. The fiber-immobilized lipase retained a high level of activity after six repeated uses, and almost no enzyme leakage from fiber was observed. However, the reactivity of the fiber-immobilized lipase was depressed at higher temperature, presumably due to dehydration by thermal contraction of the gel fiber.