尼龙66高强力轻型帘布的开发与应用

神马尼龙66高强力轻型帘布在保持帘布高强力、尺寸稳定性、耐热性、耐疲劳、耐冲击的良好特性的前提下，采用SNT高强度工业丝生产技术，充分挖掘工业丝的强力优势，把富余的强力通过进一步降低纤维密度转化为帘布面积优势的扩大，从而提高轮胎生产的帘布出胎率，使轮胎生产厂享受尼龙66帘布品质的同时，实现降低成本的目的。     

Analysis and comparison of two-dimensional permanent-magnet arrays for planar motor

This paper investigates three kinds of permanent-magnet arrays used in planar motors with polarity centers distributed in the lattices of a matrix. The magnetic field of every kind of magnet array is analyzed by analytical methods. First, we give a Laplace equation of magnetic scalar potential and a series of boundary conditions. Then, we derive the analytical expressions of magnet field strength and magnet flux density in the air gap of each kind of magnet array by the method of separation of variables. Finally, we compare the three types of magnet arrays on the basis of the analytical solutions.     

八种新功能晶体的比热及其与相变掺杂物关系的实验研究

本文对八种新型功能晶体Ｌｉ２Ｂ４Ｏ７、Ｂｉ１２ＴｉＯ２０、Ｂｉ１２ＧｅＯ２０、Ｂｉ１２ＧｅＯ２０、Ｂｉ４Ｇｅ３Ｏ１２、Ｓｒ１－ｘＢａｘＮｂ２Ｏ６（ｘ＝０．３３，０．４８）、ＬｉＴａＯ３等在１３０～９７３Ｋ范围内的比热行为及其与相变、组分之间的关系进行了实验研究，给出了比热的多项式拟合方程，并与用纽曼－卡普定律及用Ｗｉｋｅｌｍａｎｎ经验方程的比热计算值作了对比，为晶体比热的估算提供了依据和方法。     

Matrix unit cell scheduler (MUCS) for input-buffered ATM switches

This paper presents a novel matrix unit cell scheduler (MUCS) for input-buffered asynchronous transfer mode (ATM) switches. The MUCS concept originates from a heuristic strategy that leads to an optimal solution for cell scheduling. Numerical analysis indicates that input-buffered ATM switches scheduled by MUCS can utilize nearly 100% of the available link bandwidth. A transistor-level MUCS circuit has been designed and verified using HSPICE. The circuit features a regular structure, minimal interconnects, and a low transistor count. HSPICE simulation indicates that using 2-μm CMOS technology, the MUCS circuit can operate at clock frequency of 100 MHz     

苯基荧光酮类试剂在金属及合金光度分析中应用新进展

本文评述了近年来苯基荧光酮类试剂在金属及合金光度分析中应用的发展状况,显色反应的条件,以及相应光度分析方法的检测限和测定范围等。参考文献87篇。     

Eigenstructure assignment by decentralized output feedback-acomplete parametric approach

The problem of eigenstructure assignment in multivariable linear systems by decentralized output feedback is considered. By using a complete parametric solution of a generalized Sylvester matrix equation, parametric representations of both the left and right closed-loop eigenvectors and generalized eigenvectors as well as the feedback gains with respect to the closed-loop eigenvalues and two series of partially free parameter vectors are established. The obtained result does not require any conditions on the closed-loop eigenvalues, and generalizes some previous results in this area. An example shows the effect of the proposed approach     

分散剂FDN对G级油井水泥作用机理探讨

采用液相电导法和酸度法研究了分散剂FDN对G级油井水泥水化速度的影响。发现FDN促进水泥的早期水化,但吸附-络合作用及磺酸根离子对Ca(OH)_2核晶过程的“毒化”作用使后期水化速度减慢。本研究证实ζ电位升高是FDN广生分散作用的主要因素。当FDN的吸附达饱和时,ζ电位达最大值,水泥浆的分散程度最大。     

锥形有源条半导体光放大器增益和饱和特性分析

以行波半导体光放大器速度方程为基础，采用传输矩阵方法，对锥形结构半导体光放大器的增益和饱和特性进行理论研究。讨论了不同锥形长度，不同结构时的增益和饱和特性差异。理论研究表明，锥形结构能改善半导体光放大器的偏振灵敏度。在同一锥度下，长锥形长度能提高饱和增益，降低偏振度。在进行半导体光放大器有源条结构设计时要综合考虑锥度及锥形长度的影响，以实现结构优化 。     

浅谈实验室检验在科研生产中的作用

文章阐述了实验窀检验在科研生产中的作用及发挥作用的巨大潜力。     

Development of a heterogeneous microstructurally based finite element model for the prediction of forming limit diagram for sheet material

A heterogeneous finite element model with randomly distributed inhomogeneities has been developed for the determination of the forming limit diagram (FLD) for thin aluminum sheet material based on the prediction of localized necking. The strength difference between the inhomogeneities and the matrix is ascertained either from the fluctuation of the experimental stress-strain curve or from a micromechanical analysis that uses a representative particle field. By changing the specimen geometry and friction conditions, different stress states (or strain paths) are achieved. A plot of the critical Oyane fracture parameter is used to identify the limit strain state. Also, a plot of equivalent plastic strain rate is used to distinguish the boundary of intense shear bands and hence to identify where to take the measurement point. Both a plane stress model and a three-dimensional (3-D) model are adopted to predict the shear banding phenomenon and hence the FLD. The predicted FLD agrees well with the measurements from a recent round robin experimental FLD involving several independent research laboratories. The Taguchi method is applied to assess how the various parameters involved in the heterogeneous model affect the calculated forming limit strain.