Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Development of Stretch Solder Interconnections for Wafer Level Packaging

A wafer level packaging technique has been developed with an inherent advantage of good solder joint co-planarity suitable for wafer level testing. A suitable weak metallization scheme has also been established for the detachment process. During the fabrication process, the compliancy of the solder joint is enhanced through stretching to achieve a small shape factor. Thermal cycling reliability of these hourglass-shaped, stretch solder interconnections has been found to be considerably better than that of the conventional spherical-shaped solder bumps.     

徐州地区采暖教室内CO2污染影响因素分析

在徐州市采暖季节期间，实测3所高校3栋教学楼典型教室的室内CO2浓度、室内人员密度、室外空气流速等参数，分析不同状态的教室、不同的人员密度和不同的室外空气流速对室内CO2浓度的影响，提出改善采暖教室内CO2浓度的措施。     

公司大门工程建设施工

大门小品建筑属多项目综合性工程。本文作者从管理者的角度 ,通过对公司大门及附属工程施工质量控制的总结 ,说明了质量控制应贯穿于工程施工的全过程     

磷矿中七种金属元素的光谱法测定

研究了磷矿样品中7种金属元素锰、钴、镍，锌、铬、钼及铋的分析方法，选择了灵敏度高干扰少的谱线，绘制出工作曲线，对样品进行了科学处理，不必进行化学分离即可对七种元素同时测定，经合成样分析、回收实验及样品测定，证明此方法精确可靠，其回收率在98％-102％之间。     

MALL在中国的现状及其建筑设计要点

该文介绍了Mall的产生条件和国内发展概况，并结合实例分析，着重论述建筑设计方面的有关问题。     

Traveling-wave piezoelectric linear motor Part I: the stator design.

A new type of piezoelectric linear motor incorporating a traveling wave has been developed. The linear motor is comprised of a stator and a carriage. The stator design, which consists of a meander-line structure and gear teeth mounted on the meander-line structure, is the focus of this article. The meander-line structure is constructed with bimorph actuators arranged in a line. These actuators are driven by two phased sets of alternating current (ac) in order to generate a traveling wave. The traveling wave is transferred to the gear teeth, by which the carriage is driven. Modeling of the stator is derived by use of a strain energy method. The performance of various materials is evaluated by analytical and experimental methods. The analytical and the experimental results are quite approximate. Modal analysis is investigated using ANSYS. Appropriate modes associated with ultrasonic levels of resonant frequency are selected to obtain desired motion and to enhance the output performance. Surface speed for various applied input voltage are studied and indicate a nearly linear relationship. The stator in combination with the carriage makes up the linear motor.