改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

以奥林匹克精神为纲——中国运动鞋品牌运行之我见

2008年29届奥运会在北京举行，使得有关奥运的话题成为热门中的热门，与运动有关或无关的众多品牌、厂商对北京奥运年均寄予厚望，为赢取更大的收获和提升品牌知名度作最大的努力。其实早在几年前，国内外运动鞋品牌企业就已经大张旗鼓，在产品研发与广告宣传等多方面投入重金，为在这次北京奥运年带来的难得契机中处于市场制高点或明或隐地博杀着。     

Predeployed secure key distribution mechanisms in sensor networks: current state-of-the-art and a new approach using time information

In this article we survey a number of predeployed secure key distribution (PSKD) schemes proposed in the technical literature. We also propose a new time-based PSKD (TPSKD), which operates under the assumption of loose time synchronization, and discuss the performance of the scheme. Since the TPSKD scheme uses time information, which would typically already be available in sensor nodes, the cost of the scheme?s implementation is low.     

提高开卷线纵剪机精度的研究

通过对纵剪机右立柱轴承间隙测量方法和左立柱导向结构的改进，保证了加工精度，易于操作，提高了生产效率。     

Noise–Power Optimization of Incremental Data Converters

Incremental data converters (IDCs) are useful in instrumentation and measurement applications, where low-frequency analog signals need to be converted into digital form with high accuracy and low power dissipation. They are particularly well suited for applications where a single analog-digital converter is multiplexed between many channels. This paper proposes an exact design methodology for IDCs, which optimizes the signal-to-noise ratio of the converter under practical design constraints. The process also allows the designer to apportion the noise budget in an arbitrary manner between thermal and quantization noise. The design process is illustrated by an example which describes the optimization of a third-order multiplexed IDC.     

SU-8 3D microoptic components fabricated by inclined UV lithography in water

Out-of-plane microlenses and microoptical fiber holder are two of the most important components for building an integrated microoptic system with a precise alignment accuracy. In this paper, a simple and convenient method to fabricate these components from SU-8 by using inclined UV lithography in water is proposed. It consists of two perpendicular exposures in SU-8 at ±45°. DI water possesses a low absorption coefficient and a moderate and stable value of refractive index in near UV. Using water, the exposure angle in SU-8 can be increased to 50° from 35° in air necessary to pattern the desired 45° slope of the sidewalls. The principle of the proposed technique and the detailed fabrication process of the microoptic components will be presented. The integratability of the fabricated components was demonstrated by the fabrication of the microoptical fiber holder with a pre-aligned out-of-plane microlens.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

单环氧背面漆在八钢彩涂机组生产中存在的问题及解决方案

对八钢彩涂机组生产中单环氧背面漆的应用进行了分析,介绍了实际生产中使用单环氧背面漆存在的问题,并制定出相应解决措施及方案,确保彩涂单环氧背面漆的表面质量及机械性能的要求.