环境中氚和碳-14

本文介绍了加拿大恰克河实验室有关氚和碳－14在环境中行为和评价的研究。     

8Li次级束的产生

在北京串列加速器次级束流线上通过2 H(7Li,8Li) 1H逆运动学反应产生了用于核天体物理研究的8Li次级束。准直后的次级束纯度达到 80 %以上 ,对于 44MeV的7Li强度约为 3 0s- 1·pnA- 1,可以用来进行逆几何转移反应的实验测量。     

2007年国外有机硅进展

根据2007年公开发表的相关资料,综述了2007年国外有机硅行业的市场动向、行业动向及有机硅产品的研发进展.     

Structure and properties of CE/CTBN/EP blends: II. Effect of EP on the mechanical properties and thermostability of the CE/CTBN system

Carboxyl‐terminated butadiene‐acrylonitrile rubber (CTBN) has often been used to improve the toughness of cyanate ester (CE) resin while sacrificing modulus and thermostability. In this paper, the addition of the appropriate amount of epoxy resin (EP) to the CE/CTBN system is shown to not only increase the modulus and thermostability of the blend, but also improve the toughness. The values of impact strength showed a maximum for the CE/CTBN/EP 100/5/5 blend. The temperature of 10 % weight loss (T₁₀) improves from 376 °C for CE/CTBN 100/5 to 407 °C for the CE/CTBN/EP 100/5/2.5 blend. It is proposed that addition of the appropriate amount of EP can decrease the mobility and increase the stability of CTBN via the reaction between the terminal carboxyl group of CTBN and the hydroxyl group of EP. But a very high EP concentration will decrease the crosslinking density of CE, consequently reducing the mechanical properties and thermostability of the blends. Copyright © 2004 Society of Chemical Industry     

二维多波束蜂窝网覆盖方法研究

提出一种基于二维多波束形成的蜂窝网覆盖方法,该方法旨在通过对平面阵阵元权矢量的控制,使所形成的波束在空域上呈非均匀蜂窝网结构,达到重点地区覆盖密度高,非重点区域覆盖密度低的目的,减小资源利用率,并重点分析了波束设计思路和权值的计算方法,仿真结果表明:该覆盖方法是有效的.     

憎水性栀子蓝色素制备的研究

以浓盐酸为催化剂,采用乙酸酐酯化处理水溶性栀子蓝色素,制备了憎水性栀子蓝色素.探讨了栀子蓝色素与乙酸酐料液比、反应时间和反应温度等因素对憎水性栀子蓝色素色价的影响.结果表明:采用料液比1:20,在常温下反应4 h,为制备憎水性栀子蓝色素的最优条件.同时,通过红外光谱、可见吸收光谱及溶解性对栀子蓝色素的酯化改性进行了初步的探讨.     

Local residence time,residence revolution,and residence volume distributions in twin‐screw extruders

This work was aimed at studying the overall, partial, and local residence time distributions (RTD); overall, partial and local residence revolution distributions (RRD) and overall, partial and local residence volume distributions (RVD) in a co‐rotating twin screw extruder, on the one hand; and establishing the relationships among them, on the other hand. Emphasis was placed on the effects of the type and geometry of mixing elements (a gear block and various types of kneading elements differing in staggering angle) and process parameters on the RTD, RRD and RVD. The overall and partial RTD were directly measured in‐line during the extrusion process and the local ones were calculated by deconvolution based on a statistical theory. The local RTD allowed comparing the mixing performance of mixing elements. Also it was confirmed both experimentally and theoretically that specific throughput, defined as a ratio of throughput (Q) over screw speed (N), controlled all the above three types of residence distributions, be they local, partial or overall. The RRD and RVD do not provide more information on an extrusion process than the corresponding RTD. Rather they are different ways of representing the same phenomena. POLYM. ENG. SCI., 48:19–28, 2008. © 2007 Society of Plastics Engineers     

Global practical stabilization of planar linear systems in the presence of actuator saturation and input additive disturbance

In this note, we revisit the problem of global practical stabilization for planar linear systems subject to actuator saturation and input additive disturbances. A parameterized linear state feedback law is designed such that, by tuning the value of the parameter, all trajectories of the closed-loop system converge to an arbitrarily small neighborhood of the origin in a finite time and remain in there.     

Cr-Mo solid solutions forced by high-energy ball milling

Mixtures of Cr and Mo elemental powders, with the nominal compositions Cr₂₅Mo₇₅, Cr₅₀Mo₅₀, and Cr₇₅Mo₂₅, are processed by high-energy ball milling at ambient temperature. Milling is observed to force the mixing of the immiscible bcc elements Cr and Mo into solid solutions. The lattice parameter of these solid solutions, measured by X-ray diffraction (XRD), displays the expected positive deviation from Vegard’s law. These deviations are compared to the ones predicted by Eshelby’s inclusion model for dilute alloys. The conventional Williamson-Hall approach is shown to fail to determine the grain size in as-milled samples, probably due to the high density of dislocations. Annealing at 700 °C for 10 hours under argon leads to a large reduction in structural defect density, without inducing any significant decomposition. The mixing measured in Cr-Mo is discussed in the broader context of the mechanical mixing forced by ball milling in moderately immiscible systems.