Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

化灰系统的几项改造

对化灰工序设备的改进、改造的一些原因及效果情况分别进行了分析介绍。     

Preparation of CeO2-ZrO2 mixed oxide with high surface area and high thermal stability

Ceria-zirconia solid particles have been recognized as a key material of the automotive exhaust catalysts since they can release and uptake oxygen owing to the rapid reversible oxidation states of cerium between Ce³⁺ and Ce⁴⁺. Several methods have recently been described to prepare the CeO₂-ZrO₂ solid particles used in the catalysts. In this paper, a new coprecipitation method is used to prepare the CeO₂-ZrO₂ solid particles. The Ce-Zr alcogel is dried and calcined in flowing N₂ not in flowing air under atmospheric pressure. The results show that the ceria-zirconia sample calcined at 650 °C has high surface area over 90 m²g⁻¹, which drops to 40 m²g⁻¹ following treatment at 900°C.     

6314 ZZ轴承异常声分析

针对6314 ZZz轴承在运行过程中出现异常声的现象,对轴承进行了拆套检查和寿命校核计算,分析得出润滑脂失效是造成异常声的原因,润滑脂的选用应根据实际工况确定.     

The importance of electrochemistry-related etching in thegate-groove fabrication for InAlAs/InGaAs HFETs

For the first time, the surface metal on nonalloyed ohmic electrodes is found to significantly change the profiles of gate grooves, when resist openings are employed to monitor drain current during wet-chemical gate recess for sub-micron InAlAs/lnGaAs heterojunction field-effect transistors (HFETs). The surface metal of Ni enhances the etching rate in comparison with that in the absence of electrodes by a factor of 4 and 10, laterally and vertically, which is favorable to fabricate deep gate grooves with small side etching. The Pt surface metal, however, leads to preferential etching of InGaAs over InAlAs, which can be useful to realize large side etching. The existence of an electrochemistry-related etching component, which arises when the ohmic electrodes are present during recess etching, is considered to be responsible for these behaviors     

Modified atmosphere packaging of a mixed prepared vegetable salad dish

The aim of this study was to design a modified atmosphere package for a mixed vegetable salad consisting of 75 g of cut carrot, 55 g of cut cucumber, 20 g of sliced garlic and 50 g of whole green pepper. Respiration data of all the components were combined with film permeability data to predict package atmospheres and design optimal packages for experimental testing for improved shelf-life of the produce. The optimal package avoided minimum O₂ and maximum CO₂ tolerance limits, and chilling injury temperatures for any component. A pouch form package made of 27 mm low density polyethylene developed a modified atmosphere of 2.0–2.1% O₂ and 5.5–5.7% CO₂, which was beneficial for all components and provided better quality retention than other test packages.     

引黄五座泵站火灾自动报警及联动控制系统

介绍了引黄工程五座泵站的火灾自动报警系统的组成及功能，对泵站的火灾探测系统、报警系统、联动控制系统、灭火系统、控制台等原理进行了详细说明，供同行参考借鉴。     

缺血性糖尿病下肢病变的膝下动脉成形术

目的探讨膝下动脉的球囊成形术在治疗糖尿病缺血性下肢病变中的价值。方法对５３例糖尿病合并缺血性下肢病变患者６４侧缺血性下肢进行膝下动脉Deep球囊扩张成形术。对比患者手术前后临床症状的改变及足部溃疡的变化。结果５３例患者共１１９支动脉分支接受PTA治疗，５０例患者的１０１个分支成功地开通，技术成功率为８４．９％，所有５０例患者的临床症状均明显缓解，足部溃疡均变小，无需截肢。结论膝下动脉的球囊成形术是治疗缺血性糖尿病下肢病变安全有效的微创手段     

静态电子轨道衡组成部分解析及其合理选择

阐述静态电子轨道衡诸多优点;工作原理、允许误差及误差分配;轨道衡的结构组成部分、解析各部分的工作特性及技术指标要求;合理选配及推荐实例.