Removal of imidacloprid and acetamiprid from tea infusions by microfiltration membrane

Removal of imidacloprid and acetamiprid in tea infusions by microfiltration membrane using dead‐end model was investigated in the present study. The results showed that microfiltration significantly promoted the removal of both pesticides (P < 0.05) in tea infusions. Furthermore, the extent of removal was strongly influenced by the pore size of membrane, operational pressure and the concentrations of tea infusions. The initial concentration of imidacloprid and acetamiprid showed no significant effect on their removal rates. The maximum removal rates were 79.7% for imidacloprid and 81.9% acetamiprid. The changes in major chemical components of tea infusions after microfiltration were evaluated. The results indicated that microfiltration caused no considerable changes in total polyphenols and total free amino acids, and small but statistically significant losses (6.3–18.0%) of eight catechins and three methylxanthines when filtration volume reached to 200 mL. The present study validated the application of microfiltration as a potentially feasible and promising method for the removal of imidacloprid and acetamiprid residues from tea infusions.     

Viscoplastic behavior of AA7075 aluminum alloy at high strain rate

Journal of Mechanical Science and Technology - The flow stress increases with the increase in strain rate. This phenomenon is the strain rate effect of plastic deformation. Hopkinson experiment...     

THE effect of Srandom DOPANT fluctuation on threshold voltage and drain current variation in junctionless nanotransistors

We investigate the effect of dopant random fluctuation on threshold voltage and drain current variation in a two-gate nanoscale transistor. We used a quantum-corrected technology computer aided design simulation to run the simulation (10000 randomizations). With this simulation, we could study the effects of varying the dimensions (length and width), and thicknesses of oxide and dopant factors of a transistor on the threshold voltage and drain current in subthreshold region (off) and overthreshold (on). It was found that in the subthreshold region the variability of the drain current and threshold voltage is relatively fixed while in the overthreshold region the variability of the threshold voltage and drain current decreases remarkably, despite the slight reduction of gate voltage diffusion (compared with that of the subthreshold). These results have been interpreted by using previously reported models for threshold current variability, load displacement, and simple analytical calculations. Scaling analysis shows that the variability of the characteristics of this semiconductor increases as the effects of the short channel increases. Therefore, with a slight increase of length and a reduction of width, oxide thickness, and dopant factor, we could correct the effect of the short channel.     

Landau-Zener模型中纠缠演化及转移的研究

研究了受外场驱动的两个二能级系统分别与两个单模量子化光场相互作用模型中纠缠演化及转移问题。该工作主要是对外场驱动的Landau-Zener模型进行了研究，采用旋转波近似的方法，通过数值计算详细分析了二能级系统初始状态、能级间的耦合常数以及驱动外场的参数对子系统间纠缠和转移特性的影响。结果表明，适当调节模型中的参数，可以使系统初始纠缠完全转移为光腔场间的纠缠，实现二能级系统与光场间的最大纠缠转移。     

双馈风机低电压穿越的改进技术

为提高电压跌落条件下双馈风电机组的运行稳定性,介绍了crowbar与chopper共同配合作用的低电压穿越技术,并从提高crowbar阻值整定上限这一角度通过理论分析与仿真验证说明了crowbar与chopper配合作用的优势。提出低电压穿越过程中机侧变流器的无扰切换控制方法,通过仿真验证了这种方法可以大大减少crowbar投切次数与低穿过渡时间,且控制简单可行。     

Recent progress of the gas diffusion layer in proton exchange membrane fuel cells: Material and structure designs of microporous layer

Proton exchange membrane fuel cells (PEMFCs) have become the most attractive power supply units for stationary and mobile applications. The operation, design characteristics, as well as performance of PEMFCs, are closely related to the multiphase transport of mass, heat, and electricity in the cell, a critical of which is the gas diffusion layer (GDL). It is very important to guarantee the transmission of water and gasses under high current density, and which is the weakness of PEMFCs at present. Microporous layer (MPL) is considered to be the key variable for mass transfer, so varieties of works focus on modification of MPL materials and its structure design. However, there is still a lack of special review to summarize and prospect the progress of MPL in recent years. This review article therefore focuses on the insights and comprehensive understanding of four critical issues of the MPL, the porosity, pore size distribution, wettability, structural design and the durability of MPL. At last, the conclusion and recommendations section summarized the future prospects and recommendations for possible research opportunities.     

基于SoC的多轴驱控一体化平台设计

随着FPGA技术和电力电机技术的发展,FPGA+ARM的集成方式已经成为FPGA的发展方向.针对一体化多轴运动控制与驱动的特点,选用了集成双核ARM CPU与FPGA结合的Xilinx Zynq-7020全可编程System-on-chip(SoC)作为硬件平台,一个ARM CPU完成多轴的位置环、速度环和电流环的算法以及多轴轨迹生成,能同时完成伺服高级算法如谐振等,另一个ARM CPU完成交互功能,发挥FPGA高速运算的功能,完成6轴电流环流水线控制以及双采样双更新电流环算法.提高了系统整体带宽,实现多轴ns级同步精度以实现更精确的位置轨迹,驱控一体内部数据通过共享内存以及高速内部总线的方式进行交换,其传输速度更快、传输信息更加丰富.     

500 kV 开关弹簧机构支架螺栓断裂的原因分析及处理

HPL500B2型弹簧机构支架(BA)螺栓断裂可能导致开关分合闸失败,对其原因进行分析,发现BA螺栓由于预紧固力矩过大,接近其扭断力矩,使得作用在BA螺栓上的力偏高,BA螺栓安全系数仅为12%,安全系数较低。列出BA螺栓更换步骤及注意事项,并详细介绍分闸、合闸弹簧调整步骤,为类似事件的处理提供参考。