^125I,^131I诱发小鼠精子畸形发生率比较

本文选用 ICR 雄性小鼠,经腹腔分别注射不同剂量的~(125)I 及~(131)I,观察并比较它们对小鼠精子畸形发生率的影响及染毒后睾丸中放射性活度的变化。实验结果表明:(1)~(125)I 染毒后4—5周,0、185、370和555 kBq 各组精子畸形发生率分别为9.00‰、9.57‰、11.6‰及13.9‰;~(131)I 染毒后4—5周,上述各组精子畸形发生率分别为8.50‰、12.5‰、14.7‰和15.5‰;在相同注入量下,~(125)I 与~(131)I 诱发小鼠精子畸形发生率的差异各组均不显著(X~2检验,p>0.05)。(2)~(125)I、~(131)I 染毒后2h 至7天内,两者在睾丸中的放射性活度及变化规律相似,即在染毒后2h 达最高值,每克睾丸中~(125)I 和~(131)I 的放射性活度分别占初始注入量(370 kBq)的0.72％和0.50％,然后迅速下降,至一周时,仅分别占初始注入量的0.035％和0.011％。     

A circuit model for the class E resonant DC-DC converter regulatedat a fixed switching frequency

An averaging circuit model is developed for the class E resonant DC-DC converter regulated at a fixed switching frequency. The regulation is achieved by use of an auxiliary switch. The model is obtained based on the circuit analysis using the Fourier series expansion. Steady-state and small-signal dynamic analysis is presented, which reveals that the DC output is well controlled by the control angle of the auxiliary switch and that there exists a right-half-plane zero in the control-to-output transfer function. The analysis results are verified by the experiments     

CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.     

Q195冷轧板材轧制困难原因分析

针对部分Q195冷轧板材存在轧制困难的现象，进行了现场检验与分析。带状组织、混晶现象严重导致变形强化系数偏高是造成轧制困难的主要原因。     

Investigation on interior moisture distribution inducing dielectric anisotropy of coals

Dielectric anisotropy phenomenon of coal was detectable by many dielectric measurements. The paper presented that it was attributed to coal interior moisture distribution. A new model describing interior moisture distribution was developed basing on microstructure observation of coal. In the model, coal interior moisture distribution was analyzed and simulated numerically, the relationship between interior moisture distribution and coal dielectric property was constructed, the character of the permittivity varying with moisture content had also been studied and coal dielectric anisotropy was deduced. Corresponding experiment results were well satisfied with the model analysis, demonstrating that the interior moisture content could cause coal dielectric anisotropy.     

小纸层析法快速测定^99mTc—HMPAO放射化学纯度

采用小纸层析系统１：１的氯仿／四氢呋喃展开剂分析＾９９ｍＴｃ－ＨＭＰＡＯ的放射化学纯度，并与两个薄层析系统和一个纸层析系统的方法作比较。配对ｔ检验结果表明两种方法测定的放射化学纯度无显著差异；放射化学纯度在７４．２％－９６．４％，小纸层析法与薄层／纸层析法紧密相关，回归公式ｙ＝１．００６ｘ－０．３２３。