Reply to comments on “Error rate performance of theprojection code”

The authors reply to the comments by Koppelaar and Tolhuizen (see ibid. vol.46, no.9, p.573, 1998). They state that the optimum choice of the slopes used to perform the encoding process in a projection code always results in maximizing the minimum Hamming distance so that d=2 ^r     

Two-level optimal output feedback stabilizer design

The paper addresses the design of two-level power system stabilizers using an optimal reduced order model whose state variables are torque angles and speeds. The reduced order model retains their physical meaning and is used to design a two-level linear feedback controller that takes into account the realities and constraints of electrical power systems. The two-level control strategy is used, and a global control signal is generated from the output variables to minimize the effect of interactions. The effectiveness of this controller is evaluated and a multimachine system is given as an example to illustrate the advantages of the proposed method. Responses of the system with a two-level scheme and an optimal reduced order scheme are included for comparative analysis.     

钨铜合金药型罩及其性能

钨铜合金药型罩的应用可以提高射流对均质钢靶的侵彻能力.这一提高得益于射流密度的提高以及断裂时间的延长. 本文对钨铜合金射流及其断裂形态通过X光照像进行了研究.它的旋转效应及其炸高特性也进行了实验研究. 钨铜合金药型罩的威力实验在φ30 mm的破甲弹上进行.在相同装药条件下与紫铜罩相比,威力提高20～30%.     

三次方程求根及根的性质

给出实系数三次代数方程三个根的关系式定理。只要知道一个根，由该定理可方便地求出另外两根；对重根也适用，且更方便。     

钛对耐硫变换催化剂性能的影响

利用常压微反色谱、程序升温还原（ＴＰＲ）等技术研究了钛对耐硫变换催化剂性能的影响，结果表明：（１）钛能明显提高耐硫变换催化剂的活性，尤其是在低于６２３Ｋ时活性提高最为明显；（２）工业侧流试验后，含钛样品的保留活性及活性保留率均高于Ｋ８－１１；（３）催化剂中添加助剂ＴｉＯ２后，能显著提高对原料气中Ｈ２Ｓ含量变化的适应能力，因此可以拓宽对原料气的选择范围，对工业生产有着十分重要的现实意义。     

利用短周期地脉动推断深层地基S波速度

从二维随机波场的相关理论出发，提出了如何从短周期地脉动（频率＞０．５Ｈｚ）时域信号中计算Ｒａｙｌｅｉｇｈ波弥散曲线，进而反演深层地基剪切波（Ｓ波）速度的理论方法和分析技术，并结合实测信号的分析结果，探讨了该方法的可行性和实用性。     

圆锥形零件冲压变形与成形载荷的分析

由于悬空侧壁部分的变形状态是圆锥形零件成形的关键，而径向拉应力是实现悬空部分成形的必要条件，同时也是该部分冲压成形成败的关键为此，经力学分析得出了侧壁部分径向拉应力的解析式和造成圆锥形零件破裂的最大径向拉应力的计算式。同时分析了圆锥形零件的成形载荷。     

The investigation of 32P wire for catheter-based endovascular irradiation

The dose distribution from a 32P source has been measured and calculated in order to evaluate its application in endovascular irradiation. The source dimension was 27 mm in length and 0.3 mm in diameter and was embedded in the end of a Ni-Ti wire. Dose measurements were performed using radiochromic film in several specially designed tissue equivalent phantoms. Loevinger's point dose kernel was used for the calculation. The approximate dose rate at a radial distance of 1.5 mm from the center of the source was found to be 6.75 cGy/s per GBq (0.25 cGy/s per mCi), which allows the delivery of a therapeutic dose in a short time interval with a satisfactory homogeneity without stepping the source. However, the dose rate falls off almost exponentially along the radial distance. Therefore it may not be suitable for treating large diameter vessel from a centrally located source. The effect of a curved 32P wire source on the radial dose distribution was also investigated. The results showed that for a maximum bend of 180 degrees the dose rate was increased by as much as 20% along the inner radial distance but decreased by as much as 20% along the outer radial distance compared to the dose along a straight wire. However, for curvatures normally encountered in a clinical situation, the dose rate was changed less than 5%.     

聚苯硫醚酰胺的合成与表征

用4-氯苯甲酰4′-氯苯胺和硫化钠为原料在常压下合成了聚苯硫醚酰胺,并对其进行了表征。结果表明所合成的产物为结晶性聚合物,并且有较高的热稳定性。