φ100mm定径机轧辊孔型设计改进

针对定径机换辊后定径钢管所出现的质量问题,提出了成品机架的轧辊孔型不分配变形量和适当增大孔型直径的改进措施。     

Network traffic prediction based on a new time series model

Fast and accurate methods for predicting traffic properties and trend are essential for dynamic network resource management and congestion control. With the aim of performing online and feasible prediction of network traffic, this paper proposes a novel time series model, named adaptive autoregressive (AAR). This model is built upon an adaptive memory‐shortening technique and an adaptive‐order selection method originally developed by this study. Compared to the conventional one‐step ahead prediction using traditional Box–Jenkins time series models (e.g. AR, MA, ARMA, ARIMA and ARFIMA), performance results obtained from actual Internet traffic traces have demonstrated that the proposed AAR model is able to support online prediction of dynamic network traffic with reasonable accuracy and relatively low computation complexity. Copyright © 2005 John Wiley & Sons, Ltd.     

基于FPGA 的DES 算法实现

DES算法（数据加密标准）在信息安全领域具有广泛的应用，本文详细介绍了基于FPGA的DES算法的硬件实现。     

3,4-二甲氧基苯乙腈合成研究

介绍了 3,4 二甲氧基苯乙腈的合成方法 ,探讨了各种因素对反应收率的影响 ,产品总收率和质量分数分别大于 65 .0 %和 98%。     

磁热效应的直接测量及装置

磁热效应的测量有间接测量和直接测量两种方法。本文在比较两种测量方法各自特点的基础上,重点综述了直接测量装置的种类及特点;指出直接测量装置在室温磁制冷技术研究中的重要作用。     

高效铣环在胜科1井事故处理中的应用

胜科1井是中国石化的一口重点科学探井,在钻至井深5001m时因井眼缩径发生了卡钻事故。由于井底存在直翼扩大器、PDC钻头等含有硬质合金的落鱼,普通铣鞋无法完成套铣打捞作业,为此,专门设计了一种高效铣环。该铣环的切削元件选用了一种硬度达93.2 HRA的钛合金,经铣槽镶焊在本体上;本体选用了40CrNiMo厚壁管材,并进行了调质处理;连接螺纹选用了双级梯形同步螺纹。在胜科1井的应用表明：切削元件的强度满足了切削扩大器切削翼和PDC钻头胎体的需要,其齿形、布齿方向和出刃高度设计合理,提高了切削速度;本体性能高,切削元件焊接性能较好;双级梯形同步螺纹有效增加了连接部位的强度,具有较高的上扣扭矩,承受冲击载荷能力强。高效铣环在该井的成功应用,为今后同类型井的事故处理提供了借鉴。     

水分对高碱值硫化烷基酚钙结构和清净性的影响

采用傅立叶红外光谱仪，分析了水分对清净剂高碱值硫化烷基酚钙结构组成的影响；采用热管氧化试验法和曲轴箱模拟试验法，考察了高碱值硫化烷基酚钙在加水前后清净性能的变化；采用四球试验机和高频往复试验机，分析了水分对高碱值硫化烷基酚钙润滑性能的影响。结果表明，油中的水含量对高碱值硫化烷基酚钙的水解安定性能影响较大，并且随着水含量的增加，油品的清净性能和抗磨性能变差。     

超声-回弹-钻芯综合法测强初探

基于超声-回弹综合法和钻芯法检测结构混凝土强度的原理及优缺点分析，对采用超声-回弹综合法和钻芯取样法联合测强的方法：超声-回弹-钻芯综合法进行了理论研究，并结合统计理论给出了其中相关参数的确定方法。工程实例证明，该测试方法费用合理、损伤较小，且结果可靠、精度高、可在桥梁、基础等工程中推广应用。     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

Microstructure and fatigue characteristics of direct chill cast and electromagnetic cast 2024 Al alloy ingots

The distinct advantages of the electromagnetic casting (EMC) process consist in the presence of stirring motions in the melt, which lead to significant grain size reduction in solidified ingot. Furthermore, surface and subsurface qualities are improved due to the absence of ingot mold. However, it is impossible to achieve the aforementioned advantages in conventional direct chill casting (DCC). In order to contrast the before and after heat treatments of the microstructural and mechanical characteristics of EMC and DCC 2024 aluminium alloys, optical microscopy, scanning electron microscopy, transmission electron microscopy (TEM), X-ray diffractions (XRD), differential scanning calorimetry (DSC), etc. were carried out. Compared with the DCC ingot, the EMC ingot has better mechanical properties not only in the ascast condition but also in the as-aged condition. The DSC curves show that the EMC specimens have high enthalpy, i.e., the thermal kinetic energy to form precipitates during the aging treatment process. Despite heat treatments applied to the DCC ingot, it fails to attain the same mechanical properties as the EMC ingot. Moreover, considering the expernsive scalping operation for DCC ingots, the EMC technique, which offers a lower manufacturing cost, is one of the best manufacturing methods used in obtaining the ingots of wrought aluminum alloys.