明胶和胶囊生产干燥新工艺的研究

本文介绍了氯化锂液体除湿的工作原 理,并深入分析了其除湿工艺、主要特点和在 明胶与胶囊干燥方面的研究和应用。     

UHMWPE混炼接枝马来酸酐研究

讨论了超高相对分子质量聚乙烯(UHMWPE)混炼接枝马来酸酐(MAH)过程中，单体MAH用量、引发剂DCP用量、交联抑制剂己内酰胺(CAILA)用量、流动改性剂硬脂酸钙(CaSt2)用量及混炼温度、时间等工艺条件对UHMWPE接枝率和凝胶含量的影响。用红外光谱表征了接枝物的存在。并用滴定分析法和重量分析法测定了接枝物UHMWPE～g～MAH的接枝率和凝胶含量。实验表明，MAH用量为5份、DCP为0．15份、CALA为0．1份、CaSt2为1份时。混炼温度175∽180℃。混炼时间14min时，可得到接枝率0．75％、凝胶含量1．48%的UHMWPE接枝物。     

基于动态特性的D-LTSV语音端点检测方法

端点检测是语音信号处理的一个关键环节。为提高语音在低性噪比以及非平稳噪声环境下的端点检测性能,在长时信号变化特征(LTSV)的基础上提出一种新的D-LTSV语音端点检测方法。采用Bartlett-Welch方法估计语音谱,分析语音谱在长时域上的熵,利用倒谱的动态特性分析方法提取连续帧熵值的动态变化特征。实验结果表明,D-LTSV综合考虑了语音的非平稳性和帧间非平稳性的动态变化情况,具有比LTSV更好的分辨能力,特别是在低性噪比和非平稳噪声的环境下,D-LTSV的分辨能力提升了50.77%,能够准确地进行端点检测,具有更强的鲁棒性。     

Preparation and characterization of a PMMA/Ce(OH)3, Pr2O3/graphite nanosheet composite

An easy process for the synthesis of poly(methyl methacrylate)/Ce(OH)₃, Pr₂O₃/graphite nanosheet (PMMA/Ce(OH)₃, Pr₂O₃/NanoG) composite was developed. Graphite nanosheets (NanoG) were prepared by treating the expanded graphite with sonication in aqueous alcohol solution. The PMMA/Ce(OH)₃, Pr₂O₃/NanoG composites were prepared via in situ polymerization of MMA monomer in the presence of graphite nanosheets and Ce(OH)₃, Pr₂O₃ through reverse micelle template, in which the methyl methacrylate was designated as the oily phase. The composites were then dispersed with chloroform and coated on glass slides to form films. Scanning and transmission electron microscopy were used to characterize the structure and dispersion of the graphite nanosheets and the composites. The results showed that the high-aspect-ratio structure of the nanosheets played an important role in forming a conducting network in the PMMA matrix. From thermogravimetric analysis, the introduction of graphite nanosheets and inorganic nanopartices exhibited a beneficial effect on the thermal stability of PMMA.     

Exothermic effect in the process of electron‐beam curing of epoxy resins

Temperature measurements have been performed in the process of electron‐beam curing of EB‐I and EB‐II epoxy resin systems. The influence of initiator content, resin type, and dose rate on the temperature of the systems was studied. Transverse and longitudinal temperatures of samples in the glass vessel were also analyzed. The nature of temperature curves varied with the different epoxy resin systems in the steel mold, but did not change with different contents of the initiator. At the same time, the heat had no effect on the gel fraction of epoxy resin systems. The temperature curve was greatly affected by the dose rate, and its peak value, peak width, and plateau value also increased with it. The transverse temperature of EB‐II glass vessel samples increased as the radiation dose increased and, in the same sample, the temperature reduced as the distance between the radiation center and the test point increased. The longitudinal temperature of EB‐I and EB‐II resin systems in a glass vessel decreased as the radiation depth increased. As the radiation dose increased, the temperature of the EB‐I resin system increased simultaneously, while that of the EB‐II resin system initially increased and then kept constant when the dose reached a certain value. The temperatures of these two resin systems decreased rapidly when the radiation process stopped. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2217–2222, 2004     

液相合成纳米氧化锌及其光催化性能探讨

以硝酸锌和氢氧化钠为原料,分别以水和醇作为溶剂,采用液相直接沉淀法合成纳米氧化锌。在以水为反应溶剂条件下,研究了反应时间、反应温度、反应物浓度和反应物配比对纳米氧化锌中位径和形貌的影响,得到制备较小中位径及合适长径比纳米氧化锌的最优反应条件,即:反应时间为3 h、反应温度为70 ℃、锌离子浓度为0.5 mol/L、锌离子与氢氧根浓度比为1:2。在上述最优反应条件下,研究了不同醇溶剂对纳米氧化锌中位径、形貌及其光催化性能的影响。研究发现,随着溶剂碳链长度的增长,纳米氧化锌中位径呈现上下波动,无明显变化规律,形貌由球状向柱状发展,光催化性能总体不断减弱。     

NC74-1型氨合成催化剂的升温还原及应用

介绍了NC74-1氨合成催化剂在山东华鲁恒升化工股份有限公司大氮肥氨合成的装填、升温还原及使用情况。     

积层多层板用UV油墨的合成研究

采用丙烯酸改性环氧树脂E－44的方法，合成了环氧丙烯酸酯预聚物，并将其用在UV光固化油墨的配方中。在树脂合成过程中，研究了反应温度，催化剂，阻聚剂等因素对合 产品的影响。通过L9(3^4)正交试验，得到了优化的工艺参数：反应温度为90℃，催化剂为N，N－二甲苯胺，用量1％；阻聚剂对苯二酚，用量0．5％，投料环氧树脂和丙烯酸的摩尔比为1：1．08。     

Investigation on the early and late stage phase-separation dynamics of poly(methyl methacrylate)/poly(α-methyl styrene-co-acrylonitrile) blends through rheological and scattering functions

The phase-separation behavior of poly(methyl methacrylate)/poly(α-methyl styrene-co-acrylonitrile) (PMMA/α-MSAN) blends with two different compositions was studied by time-resolved small angle light scattering (SALS) in the spinodal decomposition (SD) regime from 160 to 210 °C. The rheological function (WLF-like equation) was introduced into the processing of light scattering data. It was found that the WLF-like equation was applicable to describe the temperature dependence of apparent diffusion coefficient D_app and the relaxation time τ of normalized scattering intensity (I(t)−I(0))/(I_m−I(0)) at the early stage of SD, as well as the relaxation time τ of maximum scattering intensity I_m and characteristic scattering vector q_m with I_m at the late stage of SD for PMMA/α-MSAN blends with two different compositions. This is in consistence with the phase-separation behavior of PMMA/SAN reported in our previous paper.     

Electrochemical reaction of the SiMn/C composite for anode in lithium ion batteries

The SiMn-graphite composite powder was prepared by mechanical ball milling and its electrochemical performances were evaluated as the candidate anode materials for lithium ion batteries. It is found that the cyclic performance of the composite materials is improved significantly compared to SiMn alloy and pure silicon. The heat treatment of the electrodes is beneficial for enhancing the cyclic stabilities. The SiMn-20 wt.% graphite composite electrode after annealing at 200 °C has an initial reversible capacity of 463 mAh g⁻¹ and a charge-discharge efficiency of 70%. Moreover, the reversible capacity maintains 426 mAh g⁻¹ after 30 cycles with a coulomb efficiency of over 97%. The phase structure and morphology of the composite were analyzed by X-ray diffraction (XRD) and scanning electron microscopy. The lithiation/delithiation behavior was investigated by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry. The composite materials appear to be promising candidates as negative electrodes for lithium rechargeable batteries.