排序方式: 共有69条查询结果,搜索用时 359 毫秒
51.
在 1.8 ks,10 73 K~ 1173 K条件下对 Al2 O3/ ( Ag72 Cu2 8) 97Ti3/ Ti- 6Al- 4 V进行了钎焊试验。通过扫描电镜、波谱、能谱、X射线衍射对界面结构进行了分析。小于 112 3 K的界面结构为 Al2 O3/ Cu2 Ti4 O/ Cu4 Ti3/ Ag- Cu共晶 +富 Ag相 + Ti固溶体 ;1173 K的界面结构为 Al2 O3/ Cu3Ti O5+ Cu Al2 O4 / Cu4 Ti3/富 Ag相。采用拉剪试验测试了接头剪切强度。在 1.8ks,112 3 K时剪切强度最高达到 189MPa,大于或小于 112 3 K接头强度呈下降趋势。 相似文献
52.
53.
通过建立三维有限元模型,对不同焊接条件下6 mm厚AH36钢薄板焊接残余应力峰值和分布进行了数值计算和试验研究.结果表明,在冷却方式相同的情况下,焊接应力峰值与热输入相关,采用混合焊方法的试样应力较大;在焊接方法相同的情况下,不同冷却方式的纵向焊接应力分布规律不同.与常规焊相比随焊激冷改善了焊接残余应力场分布,尤其是降低了残余拉应力峰值.为验证有限元模拟结果的准确性,采用相同参数进行焊接试验,试验结果与数值模拟结果基本一致,表明采用三维有限元模拟技术可以掌握不同焊接条件下焊接应力演变规律,为控制焊接残余应力提供了依据. 相似文献
54.
Effect of trace calcium on melting behavior of Ag-Cu-Zn brazing alloy by thermal analysis kinetics
下载免费PDF全文
![点击此处可从《中国焊接》网站下载免费的PDF全文](/ch/ext_images/free.gif)
The purity of the brazing alloys applied is necessary to be improved with the increasing cleanness of steel. Calcium is easily brought into the widely used brazing alloy, Ag-Cu-Zn, during the producing process. This paper aims at revealing the effect of calcium on the melting behavior of the brazing alloy. The thermal analysis kinetics of silver alloy with trace calcium was studied by using differential scanning calorimetry (DSC), and the enthalpy peaks were analyzed by differential methods. The rate constant of phase transformation in the probable brazing temperature range goes up with increasing calcium content, according to the values of the apparent activation energy, E, and the frequency constant, A. It is concluded that the calcium addition could improve the melting performance of Ag-Cu-Zn brazing alloy. 相似文献
55.
采用等离子弧粉末熔覆技术在Q345钢表面熔覆镍基碳化钨涂层,研究了粉末中不同碳化钨含量对镍基碳化钨熔覆层组织及性能的影响.借助光学显微镜、扫描电镜及X射线衍射仪分析镍基碳化钨熔覆层的组织形貌,用显微硬度计和摩擦磨损实验机分别测量镍基碳化钨熔覆层的硬度和耐磨性.结果表明:镍基碳化钨熔覆层与基层之间呈冶金结合,涂层表面无气孔缺陷.镍基碳化钨涂层组织主要由碳化钨颗粒和镍基粘结相构成,碳化钨是WC和W2 C,镍基粘结相中包含SiC、Cr23 C6 、Ni3 Si、γ-Ni等物相.随着粉末中碳化钨含量从15% (质量分数,下同)增加至50% ,熔覆涂层组织中硬质相数量增多,其硬度和耐磨性显著提高.当碳化钨含量为50%时,熔覆涂层硬度高达1 024HV10且耐磨性最好. 相似文献
56.
72Ag—28Cu钎焊TC4的接头组织及强度 总被引:9,自引:1,他引:9
在1103K,3min-30min条件下,使用72Ag-28Cu共晶钎料对TC4/TC4进行了钎焊试验。研究表明随钎焊时间增加,钎料中铜原子大量向界面迁移富集,母材Ti原子不断向钎缝溶解,在随后的冷却过程中产生共析转变并形成α—Ti Ti2Cu。试样加载1MPa,钎焊时间3min时接头常温拉伸强度为221MPa,延长钎焊时间接头强度呈增加趋势,30min时母材与钎缝界面模糊,此时强度最高达到373MPa,与不加载相比,强度平均增幅达80MPa左右。 相似文献
57.
By using the Ti/Cu contact reaction couples, the dissolution behavior of Ti and Cu in the eutectic reaction process was investigated under different conditions. The results show that the formation of eutectic liquid phase has a directional property, i.e. the eutectic liquid phase forms first at the Cu side and then spreads along the depth direction of Cu. The width of the eutectic liquid zone when Ti is placed on Cu is wider than that when Ti is placed under Cu. The shape of the upside liquid zone is wave-like. This phenomenon indicates that the formation process and spreading behavior in the upside are different from those in the underside, and there exists void effect in the Cu side of underside liquid zone, this will result in the delaying phenomenon of the contact reaction between Ti and Cu,and distinctly different shapes of the both liquid zones. The formation process of Ti/Cu eutectic liquid zone is similar to that of the traditional solid-state diffusion layer, and the relationship between the width of liquid zone and holding time obeys a square root law. 相似文献
58.
59.
铝/镀银层/钢的扩散钎焊及界面化合物的生长行为 总被引:2,自引:1,他引:1
采用扩散钎焊方法对6063铝合金/镀银层/1Cr18Ni9Ti不锈钢进行焊接,探讨焊接界面金属间化合物的生长行为。结果表明:钎缝中靠近不锈钢一侧为Fe-Al金属间化合物层,靠近铝合金一侧主要是Ag(Al)固溶体,中心区域由Ag-Al化合物和Ag(Al)固溶体混合而成;随着低温扩散保温时间的延长,化合物层厚度随之增加,Ag在铝合金一侧富集出现晶界渗透现象;钎缝中首先产生Ag-Al金属间化合物,之后共晶液相中的Al原子穿越Ag-Al金属间化合物层和残余镀银层扩散至不锈钢一侧,与Fe原子生成Fe-Al金属间化合物;在任意给定的扩散钎焊低条件下,可以对化合物层厚度进行初步估算。 相似文献
60.
研究了掺杂0.2 mass%Yb和Dy对Fe-20Cr合金在900℃空气中的氧化性能的影响,应用电化学阻抗技术研究在中性硫酸钠溶液中合金表面氧化膜的电导率,对高温氧化膜的性能进行描述并建立适当的等效模型。结果表明,加入元素Yb和Dy有助于促进合金表面富Cr氧化膜的形成,提高氧化膜的粘附性,从而改善合金的抗氧化性能,其中元素Dy的作用效果比Yb更好。Fe-20Cr 和Fe-20Cr-0.2Yb合金表面氧化膜在溶液中的电化学阻抗谱不能看到明显的双容抗弧特性,而Fe-20Cr-0.2Dy的双容抗弧特性明显,表明氧化膜是双层结构,且其表面氧化膜的电导率最小,显示更好的抗氧化性能,这与氧化动力学测量结果一致。通过与其它高温氧化分析方法进行比较,发现对于研究氧化膜的结构特点、孔隙率、缺陷性等电化学阻抗谱有其独特的优势。 相似文献