Flow Reaction Forces upon Blowdown of Safety Valves

The activation of safety valves causes the development of flow reaction forces that have to be transferred in an adequate way via the piping to the steel structure or via the connected vessel into the foundation. If the safety valve outlet piping is connected to a blowdown system or, in case of blowing off into the atmosphere, are equipped with a T‐piece at the outlet, the stationary reaction forces are compensated completely. The transient opening process, however, develops flow reaction forces which culminate in peaks of short duration. In this article, a simple method will be proposed for the estimation of the resulting reaction forces as a function of the length of the pipe at the safety valve outlet. CFD calculations and blowdown tests executed with a full‐lift safety valve have confirmed this method on principle. Special importance is attributed to the short duration of the effect of the reaction forces which seems to have only a negligible impact on the supporting steel structure.     

Effects of surface charge, micro-bubble size and particle size on removal efficiency of electro-flotation.

Flotation is a water treatment alternative to sedimentation, and uses small bubbles to remove low-density particles from potable water and wastewater. The effect of zeta potential, bubble size and particle size on removal efficiency of the electro-flotation process was investigated because previous model-simulations indicated that these attributes are critical for high collision efficiency between micro-bubbles and particles. Solutions containing Al3+ as the metal ion were subjected to various conditions. The zeta potentials of bubbles and particles were similar under identical conditions, and their charges were influenced by metal ion concentration and pH. Maximum removal efficiency was 98 and 12% in the presence and absence of flocculation, respectively. Removal efficiency was higher when particle size was similar to bubble size. These results agree with modelling simulations and indicate that collision efficiency is greater when the zeta potential of one is negative and that of the other is positive and when their sizes are similar.     

A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

A redundant multivalued logic for a 10-Gb/s CMOS demultiplexer IC

A redundant multivalued logic is proposed for high-speed communication ICs. In this logic, serial binary data are received and converted into parallel redundant multivalued data. Then they are restored into parallel binary data. Because of the multivalued data conversion, this logic makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, a 1:4 demultiplexer (DEMUX, serial-parallel converter) IC was fabricated using a 0.18-/spl mu/m CMOS process. The IC achieved an operating speed of 10 Gb/s with a supply voltage of only 1.3 V and with power consumption of 38 mW. This logic may achieve CMOS communication ICs with an operating speed several times greater than 10 Gb/s.     

Effect of film thickness on hydrogen content in a-Si : H

The hydrogen content, its depth distribution, and its bonding configuration have been studied in hydrogenated amorphous silicon prepared by plasma-enhanced chemical vapor deposition with hydrogen-diluted silane. Nuclear reaction analysis and infrared spectroscopy were used to determine the total amount of hydrogen and its bonded component, respectively. It has been established that the total concentration of hydrogen does not depend on the film thickness, and has a uniform depth profile. The concentration of bonded hydrogen changes with the film thickness within the measurement accuracy. The data obtained suggest the presence of molecular (non-bonded) hydrogen, uniformly distributed in concentration across the film thickness.     

The effect of ionic cross-links on the deformation behavior of homoblends made of poly(styrene-co-styrenesulfonic acid) and poly(styrene-co-4-vinylpyridine)

Deformation behavior of stoichiometric blends made from poly(styrene-co-styrenesulfonic acid) (SPS) and poly(styrene-co-4-vinylpyridine) (SVP) was investigated by TEM observation of strained thin films. An FTIR investigation revealed that ionic cross-links were formed between the component polymers upon blending due to intermolecular ion-ion interactions, which arose from proton transfer from sulfonic acid groups to pyridine groups. TEM observations indicate that the deformation mode of the blends changed from crazing only to crazing plus shear deformation, with the shear contribution becoming larger, as the ion content in the blends increased. Such changes in deformation mode can be understood as arising from an increase in the ‘effective’ strand density due to the formation of ionic cross-links upon blending. It was also found that the ionic cross-links via pyridinium cation/sulfonate anion ion pairs were more effective in inducing the transition of deformation mode than ionic cross-links via -SO₃⁻/Na⁺ or -SO₃⁻/Ca²⁺ ion pairs.     

Reducing CIC filter complexity

This paper provides several tricks to reduce the complexity and enhance the usefulness of cascaded integrator-comb (CIC) filters. The first trick shows a way to reduce the number of adders and delay elements in a multi-stage CIC interpolation filter. The result is a multiplierless scheme that performs high-order linear interpolation using CIC filters. The second trick shows a way to eliminate the integrators from CIC decimation filters. The benefit is the elimination of unpleasant data word growth problems.     

Unified Systolic-Like Architecture for DCT and DST Using Distributed Arithmetic

A common computing-core representation of the discrete cosine transform and discrete sine transform is derived and a reduced-complexity algorithm is developed for computation of the proposed computing-core. A parallel architecture based on the principle of distributed arithmetic is designed further for the computation of these transforms using the common-core algorithm. The proposed scheme not only leads to a systolic-like regular and modular hardware for computing these transforms, but also offers significant improvement in area-time efficiency over the existing structures. The structure proposed here is devoid of complicated input/output mapping and does not involve any complex control. Unlike the convolution-based structures, it does not restrict the transform length to be a prime or multiple of prime and can be utilized as a reusable core for cost-effective, memory-efficient, high-throughput implementation of either of these transforms