RF microelectronics for W-CDMA mobile communication systems

Third generation (3G) mobile communication systems are now just starting to be introduced. With a maximum data rate of 2 Mbit/s they will make wireless access to broadband data services like the Internet or video applications feasible. Most of the different physical layer technologies summarised under the acronym 3G are based on wideband-CDMA (W-CDMA), in contrast to existing second generation systems, which mostly use TDMA and FDMA. This has severe consequences for the design of the transceiver front-ends. During standardisation these were assumed to have an adequate RF performance yet they still present a performance bottleneck for the system. Starting with a short introduction to UMTS (Universal Mobile Telecommunications System)-the 3G standard to be deployed in Europe and already operating in Japan-this paper describes by way of example some of the test cases specified for UMTS and their impact on the analogue front-end. It is shown that accurate simulation of all the analogue and digital signal processing is necessary in order to predict the RF performance needed of today's commercial RFICs. The paper then presents and reviews some actual design examples. Finally, possible technologies and techniques for application in future mobile terminals are discussed     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

An expert aid to fault diagnosis and trouble-shooting in satellitecommunications

Presents the Satellite Communications Network Expert (SaNE), a knowledge-based aid designed to provide engineering support for fault diagnosis. The SaNE is composed of two elements: a satcom network model, which simulates the structure and functionality of a system based loosely upon a large military satcom network, and a diagnostic component, which uses knowledge- and model-based reasoning techniques to analyse system anomalies and diagnose possible causes for the alarms such networks generate. The development cycle is described, emphasising lessons learnt during development and testing and the advantages and disadvantages of the techniques applied. The goal of the SaNE project is primarily commercial acceptance rather than innovation. The authors illustrate how novel concepts can be implemented in a practical system without compromising this goal     

Gastrointestinal problems in diabetes

Gastrointestinal symptoms are often encountered in patients with diabetes mellitus. Symptoms may arise in any region of the alimentary tract; common symptoms are heartburn, nausea, vomiting, diarrhea, constipation, fecal incontinence, and abdominal pain. This article reviews practical approaches to the identification of the pathophysiologic mechanisms involved in diabetic enteropathies and their complications and briefly outlines strategies to treat these symptoms. Particular emphasis is placed on applied physiologic tests and the choice of pharmacotherapy (e.g., cisapride, erythromycin, or octeotide). The current role of pancreatic transplantations also is briefly reviewed.     

Increasing the service properties of weld joints by electrohydroimpulse treatment

Known examples of the positive influence of electrohydroimpulse treatment on the quality of weld joints of various steels, particularly including an increase in their long-term and cyclic strength and also corrosion resistance, are analyzed. It is shown that in this case there is a reduction in residual macro- and micro-stresses and also a change in the parameters of the dislocation structure of the joint metal in the direction of stabilization of it.Translated from Problemy Prochnosti, No. 4, pp. 119–123, April, 1996.     

Thermal expansion of semiconductor materials

The thermal expansion of tellurides of germanium, bismuth, and intermetallic compounds is investigated over the temperature range 293-973 K.Belarusian Agricultural Technical University, Minsk. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 66, No. 5, pp. 612–616, May 1994.