In situ time-resolved X-ray diffraction of tobermorite formation in autoclaved aerated concrete: Influence of silica source reactivity and Al addition

The hydrothermal formation of tobermorite during the processing of autoclaved aerated concrete was investigated by in situ X-ray diffraction (XRD) analysis. High-energy X-rays from a synchrotron radiation source in combination with a newly developed autoclave cell and a photon-counting pixel array detector were used.To investigate the effects of the silica source, reactive quartz from chert and less-reactive quartz from quartz sand were used as starting materials. The effect of Al addition on tobermorite formation was also studied. In all cases, C-S-H, hydroxylellestadite and katoite were clearly observed as intermediates.Acceleration of tobermorite formation by Al addition was clearly observed. However, Al addition did not affect the dissolution rate of quartz. Two pathways, via C-S-H and katoite, were also observed in the Al-containing system. These results suggest that the structure of initially formed C-S-H is important for the subsequent tobermorite formation reactions.     

Control of carbon incorporation in AlAs grown by atomic layer epitaxy using variously orientated substrates

We demonstrate a method for successfully controlling carbon incorporation in AlAs layers grown by atomic layer epitaxy (ALE) using various GaAs substrates with different orientations. The number of alkyl radicals attached to an Al atom at the surface, which is a main factor in carbon incorporation, can be intentionally controlled by changing substrate orientation. We found that the carbon incorporation in ALE-AlAs using the (3 1 1)B surface is 2 x 10¹⁷,cm^-3, which is the lowest value ever reported for ALE-AlAs that satisfies one-monolayer self-limiting growth conditions.     

Correction and evaluation of the effect due to parasitic motion on primary accelerometer calibration

Primary accelerometer calibration is carried out under the assumption that a vibration exciter gives a rectilinear motion to an accelerometer to be calibrated. However practical vibration given by the vibration exciter includes parasitic motion such as transverse, rocking, and bending motion. Such parasitic motion would give two serious effects on primary calibration results, transverse motion effect and vibration distribution effect. Transverse motion effect is caused by an inner product of the vectors of both transverse motion and transverse sensitivity. On the other hand, the vibration distribution effect is caused by relative motion between a sensing point of accelerometer and a spot sensed by the interferometer. As these effects have close interaction between parasitic motion and measuring instruments, it would be very difficult to evaluate them by measuring independently each component.     

Identification of characterization factor for power system oscillation based on multiple synchronized phasor measurements

Electric power systems in Japan are composed of remote and distributed location of generators and loads mainly concentrated in large‐demand areas. The structures having long‐distance transmission tend to produce heavy power flow with increasing electric power demand. In addition, some independent power producers (IPP) and power producer and suppliers (PPS) are participating in the power generation business, which makes power system dynamics more complex. However, there was little observation as a whole power system. In this paper the authors present a global monitoring system of power system dynamics by using the synchronized phasor measurement of demand‐side outlets. Phasor Measurement Units (PMU) are synchronized based on the global positioning system (GPS). The purpose of this paper is to show oscillation characteristics and methods for processing original data obtained from PMU after certain power system disturbances triggered by accidents. This analysis resulted in the observation of the lowest and the second lowest frequency mode. The derivation of eigenvalue with the two‐degree‐of‐freedom model brings a monitoring of two oscillation modes. Signal processing based on wavelet analysis and simulation studies to illustrate the obtained phenomena are presented in detail. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 163(3): 10– 18, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20316     

Development of a high‐definition 32‐in. PDP

We developed the world's smallest‐profile 32‐in. HDTV PDP. By improving the luminous efficiency, a luminance of 650 cd/m² and power consumption (discharge and driving circuit) of 200 W or less was achieved. Moreover, incorporating an advanced color compensating (ACC) filter improved the PDP's color‐reproduction capability, better than that of CRTs.     

Relative pitch perception in Japanese monkeys (Macaca fuscata).

To investigate whether monkeys perceive relative pitch, the author trained 3 Japanese monkeys (Macaca fuscata) to detect changes from rising to falling contours of 3-tone sequences. Tone sequences were presented serially with transposition, so monkeys were urged to attend to cues other than the absolute frequency of a component tone. Results from probe tests with novel sequences showed that monkeys discriminated by the relative pitch when the frequency ranges of sequences were within the training range, showing a similar tendency as birds in previous studies (e.g., S. H. Hulse, J. Cynx, & J. Humpal, 1984). (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A thermodynamic study of the system CaO + Al2O3 + FexO at 1673 K

Electrochemical measurements of the solid-oxide galvanic cell: Mo/Mo + MoO₂/ZrO₂(MgO)/(CaO + Al₂O₃ + Fe_xO) + Fe(s) + Ag/Fe have been conducted at 1673 K in order to obtain the activities of Fe_xO) in CaO + Al₂O₃ + Fe_xO slags. By using the activity data for Fe_xO, the isothermal section of the phase diagram for the system CaO + Al₂O₃ + Fe_xO was derived.     

Investigation of Waste Wood as a Blast Furnace Injectant

National legislation within Japan has increased the need for the development of new process technologies that will utilize waste wood materials. In order to generate some fundamental data with respect to the possible injection of such materials into blast furnaces, a study has been made of the decomposition and gasification reactions that take place when biomass material, in this case Japanese cypress chips, are exposed to temperatures between 1673 and 2073K using a high frequency induction furnace. The relative amounts of gas, char and tar were determined as well as the concentration of the various species present in the gas phase. The results obtained from gas analysis were in good agreement with values calculated from thermodynamic equilibria.