基于USB总线的虚拟频谱分析仪设计

文章详细介绍了基于USB总线的虚拟频谱分析仪的设计过程。该仪器使用嵌入式混合处理器MC56F8323来实现动态信号的实时采集、频谱分析和数字滤波等功能。处理结果由USB2．0接口芯片CY7C68013上传至PC机．以完成数据显示、存储、绘制图形等功能。其中，CY7C68013工作于Slave FIFO模式，以实现与MC56F8323间的数据传输。该系统可同时对两路动态信号进行实时谱分析，每路采样频率高选500kHz。     

含氮化合物对NiW体系催化剂芳烃加氢性能的影响

以γ-Al2O3、B改性的γ-Al2O3、F改性的γ-Al2O3、SiO2-Al2O3为载体制备Ni、W含量相同的四种催化剂，通过程序升温还原表征考察活性金属与不同载体的相互作用。利用氮含量不同、四氢萘含量相同的四种原料考察含氮化合物对同种NiW体系催化剂四氢萘加氢的影响以及对活性金属与载体相互作用不同的催化剂四氢萘加氢的影响。结果表明，以γ-Al2O3或SiO2-Al2O3载体制备的催化剂的金属组分与载体相互作用较强，B或F改性的γ-Al2O3能显著削弱活性金属与载体的相互作用；含氮化合物对四氢萘加氢具有强烈的抑制作用，使四氢萘加氢反应的表观活化能增加；在实验研究的四种催化剂中，金属组分与载体相互作用较弱的催化剂受含氮化合物的抑制较强。     

油气吸收回收系统的研究及工业应用——(Ⅰ)中型试验及结果分析

在蒸发油气吸收回收技术小试研究的基础上，开发出常温常压吸收法油气回收中试装置，并利用已开发的吸收剂AbsFOV-97进行了中试试验。结果表明，当系统进料气、吸收剂AbsFOV-97、汽油的体积流量比为10．0：1．0：0．5、真空泵解吸压力小于13．3kPa时，系统回收率高达97％以上，高于设计指标，且回收汽油的质量满足使用要求。统计数据表明，油气回收系统进料气、尾气中平均油气摩尔质量分别为65．51、48．97g／mol，该值可为油品蒸发损耗及其控制技术的评价提供参考。     

A novel compact ring dual-mode filter with adjustable second-passband for dual-band applications

In this letter, a novel compact ring dual-mode with adjustable second-passband for dual-band applications are presented. A ring resonator with two different geometric dimensions are derived and designed to have identical fundamental and the first higher-order resonant frequencies, and to establish appropriate couplings in the structure. Moreover, the proposed filter has smaller size as compared with the basic topology of stopband filters and stepped-impedance-resonator (SIR) filters. The measured filter performance is in good agreement with the simulated response.     

炼油厂碱性污水生物催化氧化预处理工艺研究

在对炼油厂碱性污水水质分析的基础上,提出采用生物催化氧化工艺对碱性污水进行预处理。试验结果表明,在水力停留时间为4 h,曝气量(标准状态)为8 m3／h的条件下,碱性污水的硫化物去除率可达90％以上,出水中的硫化物平均值为15．2 mg/L,CODCR、酚和油的去除率分别为47．5％,44．1％,50．8％,其中CODCR体积负荷为3．85 kg／(m3·d),是传统生化处理的10倍, 达到了污水预处理的目的。     

求解二维结构-声耦合问题的一种直接方法

本文基于传递矩阵法(TMM)和虚拟边界元法(VBEM)，提出了一种求解在谐激励作用下二维结构-声耦合问题的直接法。文中对任意形状的二维弹性环建立了一阶非齐次运动微分方程组，便于用齐次扩容精细积分法求解，对于含有任意形状孔穴的无穷域流体介质的Helmholtz外问题，采用复数形式的Burton-Miller型组合层势法建立了虚拟边界元方程，保证了声压在全波数域内存在唯一解。根据叠加原理并结合最小二乘法，提出了一种耦合方程的直接解法，由于该方法不存在迭代过程，因而具有较高的计算精度和效率。文中给出了二个典型弹性环在集中谐激励力作用下声辐射算例，计算结果表明本文方法较通常采用的混合FE／BE法更为有效。     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

Study of elastic wave propagation induced by piezoelectric actuators for crack identification

The current paper provides a theoretical study of elastic wave propagation in a cracked elastic medium induced by an embedded piezoelectric actuator. The formulation of the problem is based on a newly developed actuator model and the solution of coupled crack and actuator problems. The interaction between an actuator and a crack is studied to develop basic understanding of the effect of the crack upon the wave field generated. The resulting wave field is used to simulate 'sensor signals'. Scattered wave from the crack is then regenerated by solving a reverse elastodynamic problem and used in an imaging technique to identify the crack.     

陶瓷企业实施MRPⅡ现状及问题分析

分析了我国陶瓷企业实施制造资源计划的现状，并提出了成功实施的方略，最后通过实例进行了分析。     

纳米ZrO2等离子涂层的结构,性能和工艺特点

采用大气等离子喷涂技术(APS)，制备了常规氧化锆和纳米结构氧化锆两种涂层．利用扫描电镜(SEM)对涂层的显微结构进行了观察．对两种涂层的沉积效率、表面粗糙度和显微硬度作了对比研究．结果表明，粉末原料的显微结构、粒度、形态、喷涂工艺参数(喷涂功率和距离)对涂层的显微结构有较大的影响．等离子喷涂造粒纳米氧化锆粉制备的涂层沉积效率高而稳定，其显微结构与喷涂功率和距离密切相关．与常规氧化锆涂层相比，纳米结构氧化锆涂层具有较高的显微硬度和较低的表面粗糙度．