Reaction mechanism and microstructure evolution of reaction sintered <Emphasis Type="Italic">h</Emphasis>-BN

Hexagonal boron nitride ceramic (h-BN) based on the nitridation of B powders was obtained by reaction sintering method. The effects of sintering temperature on the mechanical properties and microstructure of the resultant products were investigated and the reaction mechanism was discussed. Results showed that the reaction between B and N₂ occurred vigorously at temperatures ranging from 1 000 °C to 1 300 °C, which resulted in the generation of t-BN. When the temperature exceeded 1 450 °C, transformation from t-BN to h-BN began to occur. As the sintering temperature increased, the spherical particles of t-BN gradually transformed into fine sheet particles of h-BN. These particles subsequently displayed a compact arrangement to achieve a more uniform microstructure, thereby increasing the strength.     

Research and Application of Dynamic Equation for Full Frontal Impact

Full frontal impact theory needs researching and exploring to satisfy the primary safety design of occupant restraint system,avoiding the increasingly "engineering"trend in order to develop and design safety vehicle. After occupant restraint system is simulated by using linear elastic stiffness k,the occupant-vehicle frontal rigid barrier impact model is established. Dynamic equation of dummy chest coupling vehicle is built for full frontal impact based on ordinary vehicle deceleration by Hooke law,and the equation is solved by comparing coefficient and satisfying boundary qualifications. While relative vehicle characteristic parameters are kept unchanging,the actual vehicle deceleration is fitted to the simplified equivalent square wave( ESW),tipped equivalent square wave( TESW) and equivalent dual trapezoids wave( EDTW). Phase angle  and amplitude A of dynamic equations based on ESW,TESW and EDTW are calculated and deduced. The results show that: the dynamic equation of dummy chest coupling vehicle can be well utilized to instruct the primary safety design of full frontal impact for objective vehicle to satisfy chest deceleration demands and the equation based on TESW is best for this design.     

Fe_(40)Co_(40)Zr_(10)B_9M_1(M=Cu,Ge,Ag)合金的热稳定性及微观结构研究

采用单辊快淬法制备Fe40Co40Zr10B9Cu1、Fe40Co40Zr10B9Ge1和Fe40Co40Zr10B9Ag1非晶合金薄带,并对3种合金在不同温度下进行热处理.利用差热分析仪(DTA)和X射线衍射仪(XRD)等测试手段对样品的热稳定性及微观结构进行研究.结果表明:Fe40Co40Zr10B9Cu1、Fe40Co40Zr10B9Ge1和Fe40Co40Zr10B9Ag13种合金的激活能分别为262.4、267.6和252.3 k J/mol,说明Cu元素、Ge元素和Ag元素的添加对合金的热稳定性影响不大,Ge元素的添加最有利于提高合金的热稳定性.3种合金的晶化过程相似:非晶→非晶+α-Fe(Co)→α-Fe(Co)+Zr Co3B2+Fe(Co)3Zr.     

基于改进Kendall-f算法的发电机定子温度分析

在线监测发电机定子温度可有效发现定子部分过热性故障,如何从检测的温度数据中提取反映定子故障预警的信息是目前国内外研究的热点。该文采用可变窗改进Kendall-f算法处理监测温度数据,提取其变化趋势特征信息;采用偏度分析提取监测温度异常值,从而正确诊断定子过热性故障,仿真分析及实验结果表明该方法有效提高了定子温度监测与预警的准确率。     

Non-Fourier heat conduction in a thin gold film heated by an ultra-fast-laser

Based on the dual-phase-lagging(DPL)heat conduction model,the Cattaneo-Vernotte(CV)model and the improved CV model we investigate the one-dimensional heat conduction in gold films with nano-scale thickness exposed to an ultra-fast laser heating.The influence of system parameters on the temperature field is explored.We find that for all the non-Fourier heat conduction models considered in this work,a larger Knudsen number normally leads to a higher temperature.For the DPL model,the large ratio of the phase lag of temperature gradient to the phase lag of heat flux reduces the maximum temperature and shortens the time for the system to reach its steady state.The CV model and the improved CV model lead to the similar thermal wave behavior of the temperature field,but the thermal wave speeds for these two models are different,especially for large Knudsen numbers.When the phase lag of temperature gradient is smaller,the difference between the DPL model and the improved CV model is not significant,but for the large phase lag of temperature gradient the difference becomes quite significant,especially for the large Knudsen number.In addition,the effect of the surface accommodation coefficient,which is a parameter in the slip boundary condition,on the temperature field of the gold film heated by ultra-fast laser pulses is investigated based on the DPL model.     

Deformation transition of intact coal induced by gas injection

Gas migration in coal bed is a multiple-physical process, of which not only includes gas desorption/diffusion through coal matrix and gas Darcy flow through the cleat system, but also results in deform...     

Oxidation behavior and mechanism of aluminum oxynitride (AlON) at elevated temperatures

The oxidation behavior and mechanism of aluminum oxynitride (AlON) powder exposed to air at elevated temperatures between 800°C and 1300°C was investigated by X-ray diffractometry (XRD), scanning electron microscope (SEM), electron spin resonance (ESR), nuclear magnetic resonance (NMR), and simultaneous thermogravimetry, differential thermal analysis, and mass spectrometry techniques (TG-DTA-MS). The weight of AlON gradually increases to a maximum value at 1150°C and then decreases with further heating. Meanwhile, AlON powder undergoes chemical changes, as evidenced by lattice expansion, and turns eventually into alumina. ESR spectra reveal the occurrence of lone pair electrons in the oxidized products and the intensity of corresponding resonance signal increases before disappearing with the increase in temperature. Combined with the results of NMR and TG-DTA-MS, the measured data suggest that Al-N in [AlO₃N] tetrahedron and [AlO₅N] octahedron are gradually oxidized into Al-O-N group with lone pair electrons, which causes continuous weight gain and lattice expansion. Further oxidation at higher temperatures results in alumina and N₂.     

视觉检测系统中亮度不均匀背景的一种去除方法

刀具形状视觉检测系统中，照明不均匀对测量结果影响很大。针对这种情况，提出了基于二维二阶多项式拟合并去除不均匀背景的方法。遵循最小均方程差原理，给出了二维二阶拟合的矩阵表达式。在编制的程序中，拟合点以人机交互形式由鼠标点击选出，程序自动记录所选点的图象人材与亮度值信息，然后拟合出背景曲面，并以二值图象形式给出去除背景后的目标图象。对一幅光照模型未知的网络图象进行了背景去除，实验结果良好。     

对Al-Cu合金中α-Al及Al2Cu生长行为的探讨

研究了Al-Cu合金中α-Al和Al2Cu的生长行为,分析了初生α-Al及初生Al2Cu作为共晶核心形核的能力.结果发现,在过共晶组织中,初生相Al2Cu形貌大部分有明显的拐角,观察其平面有的呈矩形,呈现小面生长特性.而α-Al与Al2Cu共晶生长时,Al2Cu择优生长特征削弱,与α-Al耦合生长呈现非小面-非小面生长,表明Al2Cu在不同的生长阶段表现出的生长行为不同.在亚共晶组织中,初生相α-Al周围形成离异共晶的Al2Cu,而过共晶组织中初生相Al2Cu周围没有离异共晶的α-Al,表明初生相Al2Cu作为共晶层片核心的能力比初生相α-Al作为共晶层片核心的能力强.     

时效对接触线用Cu-Ag-Cr合金性能的影响

分析了固溶温度、时效及时效前冷变形量对Cu - 0 1 %Ag - 0 1 %Cr接触线用合金性能的影响 ,结果表明 :经 870℃固溶、 40 %～ 5 0 %冷变形及 480℃× 1 5h时效处理后 ,合金可获得良好的综合性能。