涂料剖析

简要分析了不同涂料体系分析程序,说明了每种涂料剖析体系中应该注意的事项。     

企业各软件的数据共享和整合分析浅谈

本文主要根据大多数企业存在各种软件各自独立运行,各软件之间数据不能相互共享,一些旧软件或不适用的软件与目前主流操作系统不兼容等问题,分析问题并用接口和整合方法解决,此平台利用云计算技术,解决大多数企业建设信息平台投资大的问题,同时方便企业使用和维护.     

Low-Temperature Dielectric Properties of Ceramic Potassium Tantalate (KTaO3)

Dielectric properties of KTaO₃ ceramic fabricated by both conventional sintering and sintering followed by isostatic hot pressing (HIP) were measured at T =4.2 to 300 K over a frequency range from 400 Hz to 4 MHz. The weak field response shows a faint peak near 10 K which has a clear relaxation character, as in high-purity single crystals. The general response is well reproduced by the Barrett function, but additional polarizability with relaxation character is also in evidence at higher temperatures. No dielectric hysteresis was observed at high fields for cycling frequencies down to 0.04 Hz anywhere in the temperature range.     

纳米稀土复合固体超强酸催化合成乙酸苄酯

采用共沉淀法制备了纳米稀土复合固体超强酸SO4^2-／ZrO2-2％Nd2O3催化剂，电镜分析表明，催化剂颗粒直径在25nm左右，比表面积测定：71．03m^2／g。酸强度-12．70〈Ho〈-11．99。并对合成乙酸苄酯的最佳反应条件进行了研究。研究表明：当苯甲醇与乙酸的物质的量比为1：2，反应时间为5h，反应温度为120℃，催化剂用量为6％苯甲醇的质量时，酯化率可达92．04％。研究发现，该催化剂可重复使用并可活化再生。     

金纳米线拉伸行为的分子动力学模拟

采用分子动力学方法模拟了不同截面尺寸金纳米线的拉伸力学行为。计算结果表明:相同长度的金纳米线弹性模量随着截面尺寸的减小而减小,而其屈服强度随着截面尺寸的减小而增大,并且发生屈服推迟现象。应力—应变曲线与形变过程相对应。在弹性变形阶段,纳米线形变不显著;随着应变量的增加,发现纳米线出现大量堆垛层错。     

Possible Energy Network with polygeneration system and CCS for China

On basis of adopting polygeneration systems for power and alternative fuels,capturing CO2 with near zero energy penalties,and storing CO2 on sites,a new kind of Energy Network can integrate energy utilization,CO2 capture,transportation and storage synthetically.Techno-economic analysis of this solution focusing on Inner Mongolia and the Yangtze River Delta districts had been carried with comparison to the chain method for energy utilization and CO2 sequestration.This solution can save 21.5% of energy,and re...     

Analysis of junction temperatures in high-power GaN-based LEDs

We presented the analysis of the incomplete conduction in bonding medium in high power GaN-based light-emitting diode (LED) packages. A numerical study was carried out with parametric model to understand the junction temperature variation due to bonding medium defects. Transient thermal measurement was performed to evaluate LED’s junction temperature. Thermal resistance from chip to lead frame was 20 K/W in our sample LED. It was suggested that only 60% of the surface area of the bonding medium was involved...     

Preparation of micro-patterned surfaces of Si-N-O films and their influence on adhesion behavior of endothelial cells

Microgrooves were prepared on Si(100) surface by photolithography and wet etching.Subsequently,Si-N-O films were deposited on the microgrooves by unbalanced magnetron sputtering(UBMS) and micro-patterned surfaces of Si-N-O films were obtained.The size of the micropatterns was measured by surface profilometer.The chemical composition of Si-N-O films were characterized by X-ray photoelectron spectrometry(XPS) and the wettability of the micropatterned surfaces was evaluated by contact angle measurement.The beh...     

A novel shaft-less double suction mini pump

A novel double suction shaft-less mini pump was developed for heat control of small energy systems in this study.The mini pump impeller with an exit diameter of 40 mm was combined with the motor rotor supported by the hybrid dynamic bearing.The specific speed of the pump was 125 min-1 m3 min-1 m.The hydraulic performance of the pump was investigated experimen-tally under four rotational speeds.From the test results,it was recognized that the pump could provide a flow discharge of 5 L/min and head of 1.5 m,w...     

Fuel combustion test in constant volume combustion chamber with built-in adaptor

Combustion tests of pre-mixture of methane and air in constant volume combustion chamber(CVCC) have been carried out by means of flame propagation photo and gas pressure measurement,the effects of CVCC body temperature,intake pressure of pre-mixture of methane and air,equivalence ratio and location of the built-in adaptor have been investigated.The whole combustion chamber can be divided into two parts,i.e.the upper combustion chamber and the lower combustion chamber,by the built-in adaptor with through hol...