Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

Analysis of a stiffener intersection eccentricity in a steel containment

Containment structures have several regions in which the continuity of the cylindrical pressure boundary is interrupted, e.g., shell penetrations, discontinuous stiffeners, and changes in the shell thickness. Significant strain concentrations can occur in these areas of discontinuity. The Sandia National Laboratories 1:8-scale steel containment equipment hatch was analyzed as an example of an eccentricity at a stiffener intersection.A portion of the as-built 1:8-scale model was modeled with the ANSYS general purpose finite element program using triangular, thin shell finite elements. The overall size of the model was determined from Saint-Venant type considerations of the stress field around the hatch. Shell elements were used to model the ring and formed stiffeners. Geometric and material nonlinear behavior were included. The model was loaded using discrete load steps up to a pressure of 165 psig. At this pressure, the maximum strain was 19.7 percent in the formed stiffener near its intersection with the ring stiffener. The finite element solution demonstrated the very localized nature of the strain field near the ring/formed stiffener intersection.In an attempt to reduce analysis costs, a small portion of the 1:8-scale model immediately surrounding the ring/formed stiffener intersection was selected for further analysis. Two smaller models, a ring/formed stiffener intersection and a ring/circular stiffener intersection, were studied. The models were significantly smaller than the regions used previously. A comparison of the two intersection models showed that the circular stiffener is a more efficient configuration.     

Intelligent identification and control for autonomous guided vehicles using adaptive fuzzy-based algorithms

Fuzzy logic was first suggested as the mechanism by which humans drive cars. This paper addresses the use of fuzzy logic and algorithms towards the intelligent autonomous motion control of land vehicles. To cope with vehicle complexities, internal parametric changes, and with unpredictable environmental effects, the controllers that are presented, whilst heuristic in nature, are self-organizing or self-learning in that they generate automatically by observation an experiential rule base that models the vehicle, and via an appropriate performance index an optimal control rule base that is robust to large parametric changes. The methodology presented is applicable to any complex process which is too difficult to model or control using conventional methods, or which has relied on the experience of a human operator. An overview of fuzzy logic and static fuzzy logic control (akin to expert systems) is provided, together with illustrative examples.     

Comparing VVR-M reactor fuel assembly heat technological capabilities

Translated from Atomnaya Énergiya, Vol. 67, No. 2, pp. 97–100, August, 1989.     

Tube-shaping unit — A way of improving the quality of shaped tubes

Lenin Dnepropetrovsk Pipe Plant. Translated from Metallurg, No. 8, p. 39, August, 1989.     

“Metallisation” of oxide surfaces observed by in situ high-resolution electron microscopy

Intense irradiation (25–40 A/cm²) at intermediate energy (400 keV) has been found to cause “metallisation” of tungsten oxide and titanium niobate crystal surfaces. The possible mechanisms and the likely consequences for high-resolution imaging of clean oxide surfaces are briefly discussed.     

Theoretical analysis of control properties for the brushless doubly fed reluctance machine

The brushless doubly fed induction machine (BDFIM) has been extensively researched for approximately 30 years, but a related machine [the brushless doubly fed reluctance machine (BDFRM)], has not. This was mainly due to the fact that reluctance rotor designs were not capable of generating saliency ratios large enough to make the BDFRM competitive with other machines. However, recent developments in reluctance rotors, spurred on by research into synchronous reluctance machines, has resulted in high saliency ratio rotors that are economic to build. This, together with the promise of higher efficiency and simpler control compared to the BDFIM, means that further investigation of the BDFRM is warranted. A relatively limited amount of work to date has been published on the BDFRM. This paper attempts to fill this void by presenting a theoretical analysis of some of the important control properties of the ideal BDFRM.     

Comparison of Solutions of the Problems of Elasticity Theory for Different Near-Boundary Elements

We consider three types of near-boundary elements: curvilinear quadrangles and families of arcs and points, and their application to a two-dimensional problem of the static theory of elasticity with boundary conditions in displacements. The comparison of the theoretical and numerical aspects of the obtained solutions is performed. It is shown that the accuracy of evaluation of the components of the vector of displacements increases in the following cases: in the case of complete quantization of the near-boundary region (but not in the case of its partial quantization or quantization with overlapping), in the case where the numbers of arcs and points increase, and in the case of simultaneous application of different types of near-boundary elements (specifically, quadrangles and families of arcs).