Influence of steric length in electrosteric surfactants on emulsion polymerization

Four PPG Avanel Series S surfactants (sodium alkyl polyether sulfonates) with varying ethylene oxide content (n = 3, 7, 9, and 15) were used to investigate the influence of the steric length in this type of electrosteric stabilizers on emulsion polymerization. The polymerization studies employing potassium persulfate as an initiator with styrene, methyl methacrylate, and vinyl acetate monomers showed no apparent change in particle size, number of particles, and polymerization rate with the changing steric length of the surfactant. Steric influences were observed in the redox-initiated systems of styrene, butyl acrylate, and methyl methacrylate. Increasing the ethylene oxide unit content from three to nine units decreased the rate of polymerization, the particle size and number in the polystyrene latexes. Polymerizations with the acrylates displayed the same trend except that the polymerization rate reached a minimum value at nine ethylene oxide units and increased when the surfactant containing 15 ethylene oxide units was used.     

Morphology, structure and properties of a poly(1-butene)/montmorillonite nanocomposite

A specifically formulated nanocomposite based on isotactic poly(1-butene) (PB) and montmorillonite was studied, by wide angle X-ray diffraction (WAXD), small angle X-ray scattering (SAXS), transmission electron microscopy (TEM) and polarized light optical microscopy, investigating the polymorphism of the polymer, and examining the interaction between PB and the silicate. Montmorillonite was found to disrupt the ordered morphology of the polymer, determining a dramatic increase in the rate of the II→I phase transition. Interaction between polymer and clay was studied by TEM and SAXS also under a quantitative point of view. A significant enhancement of physical-mechanical properties was observed, even though exfoliation did not occur, but just a slight intercalation and a reduction in the size of tactoids.     

<Emphasis Type="Italic">In situ</Emphasis> monitoring of solid fat content by means of pulsed nuclear magnetic resonance spectrometry and ultrasonics

An ultrasonic technique was developed to study the crystallization process of edible fats on-line. A chirp wave was used instead of the conventional pulser signal, thus achieving a higher signal-to-noise ratio. This enabled measurements to be made in concentrated systems [≈20% solid fat content (SFC)] through a 8.11-cm thick sample without significant signal loss. Fat samples were crystallized at 20, 25, and 30°C at a constant agitation rate of 400 rpm for 90 min. The crystallization process was followed by ultrasonic spectroscopy and a low-resolution pulsed nuclear magnetic resonance spectrometer. Specific relationships were found between ultrasonic parameters [integrated response, time of flight (TF), and full width half maximum] and SFC. TF, which is an indirect measurement of the ultrasonic velocity (v), was highly correlated to SFC (r ²>0.9) in a linear fashion (v=2.601 SFC+1433.0).     

Alarm pheromone system of leaf-footed bugLeptoglossus zonatus (Heteroptera: Coreidae)

The alarm pheromone system ofLeptoglossus zonatus (Dallas) adults was shown to be composed of hexyl acetate, hexanol, hexanal, and hexanoic acid. Single components tested in the field elicited dispersive behavior of over 70% of adults. 2-(E)-Hexenal, found in the secretion of nymphs, but not in the exudates of adults, was also active against adults. In addition, first-instar nymphs responded to the four components of the alarm pheromone of adults as well as to 2-(E)-hexenal, a component of their own alarm pheromone system. Adults and nymphs possess different alarm pheromone systems, which are not specific to their own life stage. That hemipteran alarm pheromone systems are not species-specific was supported by the fact that both adult and nymphL. zonatus responded to butanoic acid, an alarm pheromone of Alydidae, which was not found in this Coreidae species.     

The role of the Tm3+ concentration on CaMoO4 properties processed by microwave hydrothermal under stirring condition

The compounds based on calcium molybdate (CaMoO₄) are the subject of extensive research due to their excellent optical properties and a broad range of potential technological applications. In this work, we report a systematic study of CaMoO₄:Tm³⁺ phosphors synthesized by coprecipitation and processed in a microwave-hydrothermal system at low temperature (100°C) and stirring. The effect of the Tm³⁺ doping content (0%–12%) is studied in full detail to understand their role in the CaMoO₄:Tm³⁺ morphological, structural, and luminescent properties. The X-ray diffraction, Raman, and Fourier Transform Infrared spectroscopic techniques revealed that all the prepared powders have a tetragonal crystal structure with a distinct density of cation vacancies and structural disorders. The band gap remains almost constant for doping levels lower than 8%, but it narrows strongly for powders doped with 12% Tm³⁺ ions. The designed phosphors have shown two emission bands in which intensity depends on the Tm³⁺ ions doping level. For doping levels lower than 2%, the photoluminescence profile displays a broad emission band peaking at 543 nm (green). For concentrations higher than 4%, the band centered at 543 nm decreases in intensity and the near-infrared emission band at around 800 nm, assigned to ³F₃, ³H₄ → ³H₆ transitions from Tm³⁺ ion, become more intense. The outcomes of this work reveal that appropriated Tm³⁺ ions doping levels can be applied to suppress the PL emission in the visible range and improve that in the near-infrared region in CaMoO₄-based materials.     

Synthesis and characterization of eugenol-based silicone modified waterborne polyurethane with excellent properties

A eugenol-based silicone-containing monomer 4,4′-(1,1,3,3-tetramethyldisiloxane-1,3-dipropyl)bis-2-methoxyphenol(EUSi) was synthesized from eugenol and 1,1,3,3-tetramethyldisiloxane via the hydrosilylation reaction. And waterborne polyurethane (WPU) with excellent properties was obtained by using EUSi as a type of diol chain extender. The unique combination of rigidity and flexibility in the chemical structure of EUSi greatly facilitated the mechanical properties, thermal properties, and water resistance of WPU. With only a 3% dosage of EUSi, the maximum tensile strength was increased from 6.2 to 22.4 MPa, while the water absorption was decreased from 31.3% to a surprisingly 7.6%. Our work provides a new convenient strategy for the preparation of organosilicon-modified WPU with improved performance.     

Bio-based sustainable films from the Algerian Opuntia ficus-indica cladodes powder: Effect of plasticizer content

The present study investigated the fabrication and characterization of bio-based sustainable films composed of a terrestrial plant raw material, namely Opuntia ficus-indica (OFI) cladodes powder (CP) and a marine seaweed derivative, namely agar (A). The effect of glycerol concentration on the properties of the casted films was evaluated at four different contents, namely 30, 40, 50 and 60 wt%. The films present UV-blocking properties, as well as moderate mechanical performance, thermal stability, and water vapor transmission rate (WVTR). The results point to an increase in thickness, elongation at break, moisture content, water solubility, and WVTR with increasing glycerol content. On the contrary, Young's modulus, tensile strength, and water contact angle decreased as glycerol concentration increased. The best combination is obtained for the film with 30% glycerol, based on an intermediate compromise between physical, mechanical, thermal, and barrier properties. All these outcomes express the potentiality of the powder obtained from grinding the OFI cladodes as raw material to produce low-cost films for the development of sustainable packaging materials.     

Bi-layer gelatin active films with “Pitanga” leaf hydroethanolic extract and/or natamycin in the second layer

Research on biopolymers-based active films produced with natural antioxidants and/or antimicrobials has gained attention over the last few years; however, anti-mold activity has been less studied than those of anti-bacteria. The aim of this work was the development and characterization of bi-layer films based on gelatin with natamycin and/or “Pitanga” leaf hydroethanolic extract in the second thin layer in order to determine the effects of these bioactive compounds on bi-layered film properties. The films were characterized regarding their moisture content and solubility in water, optical properties, microstructure, mechanical and thermal properties, water contact angle, water vapor permeability, UV/visible light transmission, X-ray diffraction, Fourier transform infrared (FTIR) spectroscopy, and antioxidant and anti-mold activities. Active films presented activity against Penicillium spp and Aspergillus niger and demonstrated antioxidant activity, as measured by ABTS ^•+ and DPPH ^• methods. Neither additive used in the films' second layer significantly affected the films' moisture content, thermal properties or the molecular interactions of the polymer matrix, assessed by FTIR, although some mechanical properties were affected, and the water contact angle. In conclusion, bi-layer films have reduced the quantity of additives required to maintain the antioxidant and anti-mold activities, as compared to similar monolayer films of the same thickness.     

Towards a smooth design process for static communicative node‐link diagrams

Node‐link infographics are visually very rich and can communicate messages effectively, but can be very difficult to create, often involving a painstaking and artisanal process. In this paper we present an investigation of node‐link visualizations for communication and how to better support their creation. We begin by breaking down these images into their basic elements and analyzing how they are created. We then present a set of techniques aimed at improving the creation workflow by bringing more flexibility and power to users, letting them manipulate all aspects of a node‐link diagram (layout, visual attributes, etc.) while taking into account the context in which it will appear. These techniques were implemented in a proof‐of‐concept prototype called GraphCoiffure, which was designed as an intermediary step between graph drawing/editing software and image authoring applications. We describe how GraphCoiffure improves the workflow and illustrate its benefits through practical examples.     

Toward the Interactive 3D Modelling Applied to Ponte Rotto in Rome

We present the first step of a research aimed at automating a driven interactive 3D modeling of an existing architectural object. The method is based on oriented multi-image spherical panoramas produced by stitching techniques. The photogrammetric process has two steps: the creation of a semi-automatic process to find homolog points in two panoramas; the creation of parametric definitions for an interactive modeling creating points, segments, and surfaces based on the plotted points in the first step. By connecting these two steps, the creation of the model will be automatic, as we indicate the necessary points in just one panoramic photo. The principals of multi-view geometry and epipolar geometry were applied to simplify the calculation in the first step in order to create an automatic identification of the correspondent points in the other panorama. The epipolar geometry is described by both analytical and graphical programming, implementing in the first case a C++ application and in the second case a Rhinoceros and Grasshopper application. A case study of the Ponte Rotto in Rome (Italy) is presented.