AMBE-1000声码器接口电路设计方法

DVSI公司的AMBE-1000声码器芯片是一款高性能的全双工、实时语音压缩编解码芯片,可以应用于卫星通信、保密通信、视频会议等领域.文中简要介绍AMBE-1000声码器的A/D-D/A接口以及信道接口的工作原理;结合实例分别给出了AMBE-1000声码器与PCM编解码器MC14LC5480的A/D-D/A接口电路、与单片机AT89C51的信道接口电路的设计方法;最后指出了电路设计中应该注意的问题.     

关于本地传输网网络优化的探讨

根据长期工作经验,对现有网络存在的问题进行分析,提出对本地传输网网络优化的有关建议。     

关于海面无线传播模型的探讨

现有文献中一般都认为海面环境的无线传播模型近似于自由空间传播模型，但在实际测试中发现，自由空间模型预测值与实测值差别较大，不能很好地解释此类环境的信号传播。笔者根据多次海面覆盖测试的数据，分析并拟合出了新的海面传播模型。     

Preirradiation grafting of acrylic and methacrylic acid onto polyethylene films: Preparation and properties

The method of preirradiation grafting of acrylic acid and methacrylic acid onto polyethylene films was studied. The trapped radicals and hydroperoxides or diperoxides appeared to be able to induce graft polymerization. Mohr's salt was added to depress homopolymerization. The influences of crystallinity, dosage, and storage period on the grafting behavior were investigated from the viewpoint of practical application. At elevated temperature, the degree of grafting increased rapidly with reaction time initially, and then leveled off to the value of final percent grafting. Dosage and storage periods had greater extent of influence on the final percent grafting of LDPE than on that of HDPE. Electrical properties, transport properties, and mechanical properties were measured to compare the differences between acrylic-acid-and methacrylic-acid-grafted copolymer films. It was found that the properties of methacrylic-acid-grafted copolymer film was superior to those of acrylic-acid-grafted copolymer film, especially in electrical conductivity. The KOH diffusion test confirmed that grafting occurred not only on the surface but also in the interior of the polymer matrix, and the grafting is believed to proceed from the surface to the interior of the matrix.     

Disc filtration for separation of flocs from a moving bed bio-film reactor.

A Discfilter with 10 and 18 microm filter openings, respectively, was placed in parallel to a flotation plant for separation of biological flocs from a post-denitrifying Kaldnes Moving Bed Process, the last treatment step at the municipal wastewater treatment plant at Sj?unda, Malm?, Sweden. The effluent concentrations from the 10 and 18 microm filter were 2-5 and 2-8 mg SS L(-1), respectively, which is comparable to, or better than, the flotation plant. Comparison with experiences from activated sludge plants shows that the Discfilter works especially well after the Kaldnes process. Particle size distribution (PSD) studies show that particles larger than the filter openings of 10 and 18 microm are separated with approximately 90% efficiency, whereas most of the smaller particles pass the filter. This fact indicates that the major particle separation mechanism is physical blocking. These findings point to the possibility of improving the prediction of the separation efficiency by combining measurements of turbidity and suspended solids with particle size analysis.     

Traveling-wave piezoelectric linear motor Part I: the stator design.

A new type of piezoelectric linear motor incorporating a traveling wave has been developed. The linear motor is comprised of a stator and a carriage. The stator design, which consists of a meander-line structure and gear teeth mounted on the meander-line structure, is the focus of this article. The meander-line structure is constructed with bimorph actuators arranged in a line. These actuators are driven by two phased sets of alternating current (ac) in order to generate a traveling wave. The traveling wave is transferred to the gear teeth, by which the carriage is driven. Modeling of the stator is derived by use of a strain energy method. The performance of various materials is evaluated by analytical and experimental methods. The analytical and the experimental results are quite approximate. Modal analysis is investigated using ANSYS. Appropriate modes associated with ultrasonic levels of resonant frequency are selected to obtain desired motion and to enhance the output performance. Surface speed for various applied input voltage are studied and indicate a nearly linear relationship. The stator in combination with the carriage makes up the linear motor.     

Optimum power-saving method for power MOSFET width of DC/DC converters

An optimum power metal-oxide-semiconductor field effect transistor (MOSFET) width technique is proposed for enhancing the efficiency characteristics of switching DC-DC converters. By implementing a one-cycle buck DC-DC converter, it is demonstrated that the dynamic power MOSFET width controlling technique has a much improved power reduction whether the load current is light or heavy. The maximum efficiency of the buck converter is ~92% with a 3% efficiency improvement for the heavy load condition. The efficiency is further improved by ~16% for the light load condition as a result of the power reduction from the large power MOSFET transistors. Also proposed is a new error-correction loop circuit to enable a better load regulation than that of previous designs. Compared with the adaptive gate driver voltage technique, the optimum power MOSFET width can achieve a significant improvement in power saving. It is also superior to the low-voltage-swing MOSFET gate drive technique for switching DC-DC converters     

加油站油品用体积交接存在的问题及建议

叙述了目前加油站在实行按任意温度下的体积交接，由于未考虑油品体积随温度、压力、密度的变化，出现了零售损耗很大的问题。建议加油站在现阶段采用“准标准体积”交接；在由体积转换为质量计算加油站损溢时，使用油库当月发出的平均密度；当财会核销损溢时，不使用盘存的体积和固定密度进行计算的方法，而使用实际盘点的质量数，以真实反映加油站的当期损溢。     

Challenges in the Application of Stochastic Modal Identification Methods to a Cable-Stayed Bridge

This paper presents an analysis of the data collected in the ambient vibration test of the International Guadiana cable-stayed Bridge, which links Portugal and Spain, based on different output-only identification techniques: peak-picking, frequency domain decomposition, covariance-driven stochastic subspace identification, and data-driven stochastic subspace identification. The purpose of the analysis is to compare the performance of the four techniques and evaluate their efficiency in dealing with specific challenges involved in the modal identification of the tested cable-stayed bridge, namely the existence of closely spaced modes, the perturbation produced by the local vibration of stay-cables, and the variation of modal damping coefficients with wind velocity. The identified natural frequencies and mode shapes are compared with the corresponding modal parameters provided by a previously developed numerical model. Additionally, the variability of some modal damping coefficients is related with the variation of the wind characteristics and associated with a component of aerodynamic damping.     

Pretreatment of Highly Polluted Pharmaceutical Waste Broth by Wet Air Oxidation

The preoxidation of a highly polluted waste pharmaceutical fermentation broth using wet air oxidation (WAO) has been studied as a possible method for the effective removal of organics. The applied (pre)treatment method should enhance the biotreatability of the pharmaceutical fermentation broth in terms of reduced initial toxicity and higher biodegradability. Preliminary experiments in the pilot biological treatment plant were successful only at low organic loads, whereas the system collapses at higher ones. The characterization of the fermentation broth was started by common physicochemical analysis, whereas several bioassays were used to determine its impact on biological treatment plants and the environment. Toxicity prior to and after WAO was determined using the acute Vibrio fischeri test, measurement of inhibition of O2 consumption, and the Daphnia magna acute test. Ready biodegradability of the treated and untreated broth has also been assessed. WAO experiments were accomplished in the 2?L batch reactor at different temperatures (240/280°C) and operating pressures. WAO experiments confirmed reduction of the toxicity toward microorganisms, whereas oxidized wastewater was more toxic to daphnids. Biodegradability of the oxidized broth has also been enhanced. Further work has been focused on designing appropriate combination of WAO and biological processes.