Pultruded fibre reinforced polyurethane composites II. Effect of processing parameters on mechanical and thermal properties

This paper presents a novel process for the fabrication of pultruded polyurethane (PU) composites. The effects of the processing parameters on the mechanical properties (flexural strength and flexural modulus, etc.) and thermal properties (HDT) of the fibre reinforced PU composites by pultrusion have been studied. The processing parameters investigated include pulling rate (in-line speed), die temperature, filler type and content, and post-cure time and temperature. Results show that the composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio, the mechanical properties and the thermal properties of composites, the optimum die temperature can be determined. It is found that the mechanical and thermal properties increase with filler content for various types of filler. The mechanical and thermal properties increase at a suitable post-cure temperature and time. Furthermore, the properties which decreased due to the degradation of composite materials for a long post-cure time will be discussed.     

Mechanism of iodine vapor sorption in polyacetylene

Simultaneous measurements of weight uptake and conductivity variation during iodine vapor sorption of polyacetylenes (PA) at 20–25°C show that the sorption is a two-stages process. For the first stage, iodine diffusion to the fibrilar surface of the cis-rich and trans-rich PA is of Knudsen type pore diffusion as supported by the sorption measurements of hexane for the cis-rich PA, and has a diffusion coefficient in the order of 10⁷ cm²/sec. Conductivity of the PA rises rapidly and reaches a maximum at end of the stage. For the second stage, the diffusion is more restrictive and has a diffusion coefficient lower than the first stage by a factor of about 10 due to multilayer sorption of iodine, which leads to a decrease in the pore diameter and therefor the diffusion rate. In addition to the restricted diffusion in the second stage, diffusion of the iodine molecules adsorped on the fibrilar surface into the interior of the fibrils is appreciable for cis-rich PA (leading to a conductivity drop) and is negliglible for tran-rich PA (leading to insignificant variation in conductivity).     

Precipitation behavior of σ phase in fusion zone of dissimilar stainless steel welds during multi-pass GTAW process

The purpose of this study is to investigate the precipitation characteristics of σ phase in the fusion zone of stainless steel welds at various welding passes during a tungsten are welding (GTAW) process. The morphology, quantity, and chemical composition of the δ-ferrite and σ phase were analyzed using optical microscopy (OM), a ferritscope (FS), a X-ray diffractometer (XRD), scanning electron microscopy (SEM), an electron probe micro-analyzer (EPMA), and a wavelength dispersive spectrometer (WDS), respectively. Massive δ-ferrite was observed in the fusion zone of the first pass welds during welding of dissimilar stainless steels. The σ phase precipitated at the inner δ-ferrite particles and decreased δ-ferrite content during the third pass welding. The σ and δ phases can be stabilized by Si element, which promoted the phase transformation of σ→ϱ+λ₂ in the fusion zone of the third pass welds. It was found that the σ phase was a Fe−Cr−Si intermetallic compound found in the fusion zone of the third pass welds during multi-pass welding.     

环境放射化学研究中几个问题的讨论

本文从辐射环境保护和公众辐射防护的角度，讨论了放射性核素在环境中的迁移行为，放射性核素与环境介质的相互作用和放射性核素在环境中的形态等涉及到环境放射化学研究方向的问题，并讨论了它们之间相互依存的关系。     

An extraction method to determine interconnect parasitic parameters

Interconnect parasitic parameters in integrated circuits have significant impact on circuit speed. An accurate monitoring of these parameters can help to improve interconnect performance during process development, provide information for circuit design, or give useful reference for circuit failure analysis. Existing extraction methods either are destructive (such as SEM measurement) or can determine only partial parasitic parameters (such as large capacitor measurement). In this paper, we present a new method for extracting interconnect parasitic parameters, which can simultaneously determine the interlayer and intralayer capacitances, line resistance, and effective line width. The method is based on two test patterns of the same structure with different dimensions. The structure consumes less wafer area than existing methods. The method shows good agreement with SEM measurement of dielectric thickness in both nonglobal planarized and chemical-mechanical polished processes, and gives accurate prediction of the process spread of a ring oscillator speed over a wafer     

A science and technology with rich vitality — desalination

Congratulations toDesalination for its prosperity and for the contributions it has made to benefit mankind. Review the past and look forward to the future for the development of desalination technologies in China.     

A linear minimum mean square error multiuser receiver inRayleigh-fading channels

We generalize the multiuser (CDMA spread spectrum) communication systems to the fading environments. We first extend Verdu's (1986) conventional optimum receiver to Rayleigh-fading environments and then evaluate its performance. Having no knowledge of the received power at the receiving end, we therefore need an estimator to efficiently estimate the received signal strength of each user in fading environments. A linear minimum mean square error (LMMSE) unbiased estimator is proposed to attain this goal. By using the minimum mean square error (MMSE) Bayesian estimation, we further propose the LMMSE bit estimator for efficient demodulation. Its performance is close to the optimum multiuser receiver but with a much simpler polynomial complexity. To further reduce the complexity, we extend the LMMSE estimator to the sequential LMMSE estimator. In sequential estimation, we do not need to implement the matched filter banks and to perform the matrix inversion when estimating. In addition, it converges after approximately 2k iterations, where k is the number of users. With this fast convergence property and the simple structure, the sequential LMMSE estimator provides an attractive alternative to the implementation of a multiuser system     

Efficient dynamic synchronous machine simulation with harmonics

Within this paper, an efficient procedure for the dynamic simulation of faulted synchronous machines operating in the presence of harmonics is presented. The algorithm employs steady-state frequency domain techniques for simulation of the transmission system sequence networks and time domain methods for synchronous machines represented in the odq frame of reference. The procedure affords greater accuracy than conventional fault analysis techniques based strictly on steady-state methods, yet requires far less computational time than full system dynamic simulations such as those using the EMTP     

Numerical electromagnetic simulator termination de-embeddingtechnique

The authors report a novel approach whereby transmission-line end effects can be assessed by numerical simulation without recourse to the evaluation of the propagation properties of the line interconnecting the termination and excitation signal launch planes. As an example of the new technique, a microstrip open-ended line termination simulated by the finite-difference time-domain method is reported. The simulated results are compared with those obtained for the same structure but by a conventional numerical de-embedding scheme. The method presented is completely general and can be applied to any numerical electromagnetic field simulation method solving one-port or multiport networks     

加氢裂化复合催化剂使用技术的研究

使用1246与3762复合催化剂加氢裂化处理含焦化蜡油(50%以上)混合原料油时,催化剂不仅具有高脱氮能力、高转化率,同时,还具有好的加氢活性稳定性,为焦化蜡油的合理加工找到一条新路,并有显著的经济效益 。