丙酮低压一步法合成甲基异丁基酮催化剂体系研究进展

对丙酮低压一步法合成甲基异丁基酮所需要的催化剂体系及反失活机理进行了详尽的综述，并对近年来的研究工作进行了系统地分析与比较，提出了未来的研究方向。     

Numerical Filling Simulation of Injection Molding Using Three-Dimensional Model

1 Introduction During injection moulding, the rheological response of polymer melts is generally non-Newtonian and nonisothermal with the position of the moving flow front. Because of these inherent factors, it is difficult to analyze the filling process. Therefore, simplifications usually are used. For example, in middle-plane technique and dual domain technique [1], because the most injection molded parts have the characteristic of being thin but generally of complex shape, the Hele-Shaw …     

离子束混合工艺对材料抗蚀性能的影响

本文介绍了离子束混合工艺方法。与直接注入相比较,离子束混合所使用的设备造价低1/4—1/2,而生产效率可提高1—2个数量级,因而使生产成本大幅度降低,这无疑对离子束工艺的实际应用将产生巨大的促进作用。 通过对轴承材料(GCr15和Cr4Mo4V)经Cr、N、Ta不同元素的混合处理后,在0.5M H_2SO_4和0.1M NaCl的缓冲溶液中的阳极极化曲线表明经混合处理后的两种材料试样,其抗蚀能力和抗点蚀能力均大大提高,这与直接注入的试样效果是一致的。 通过俄歇谱仪和透射电镜的分析结果表明混合是成功的,且在一定的条件下,形成非晶组织。 本文的结论是,无论是离子的直接注入还是离子束混合,对提高轴承材料的抗腐蚀性能都是有效的方法,特别是离子束混合技术具有更大的应用前景。     

低发射率材料红外法向发射率谱测量方法的研究

采用热管技术研制了材料发射率谱的专用测量附件;利用双温测量技术,在P-E983型红外分光光度计及3600型数据站上进行了较低温度下低发射率材料红外法向发射率谱测量方法的研究.实测了几种材料的发射率谱;讨论了影响测量误差的诸因素.     

Effect of Preparation Methods and Condition of Precursors on the Phase Composition of Yttria-Stabilized Zirconia Powders

An yttria-stabilized zirconia powder, free of monoclinic phase, may be prepared by an oxalate method in an ethanol solution at strong acidity. This study demonstrates that the control of pH in the preparation of precursors has a significant effect on the ability of precursors to crystallize and hence plays an important role in determining the formation and fraction of various crystalline phases in the resulting yttria-stabilized zirconia powder. With the increase of pH, a precursor with a certain crystalline form may be transformed into an amorphous precursor, and a monoclinic phase appers in the phase composition of the resulting powder. The results of XRD analysis and Raman spectroscopy are discussed.     

腐蚀算法在重建一类特殊管道中的应用

针对一类特殊而不能直接对其观察的管道（如动物的血管），为了准确了解其内部特征和形态，借助计算机给出了一种用腐蚀算法来重建管道原形的方法。这种方法简单易行，而且精确度高。     

Probabilistic analysis of uncertainties in seismic hazard assessment

Sources and current methods of analysis of uncertainty from randomness, fuzziness and ignorance or incomplete knowledge in seismic hazard assessment problem are briefly discussed at beginning; understandings of the authors are then presented in the following order. All three types of uncertainty come from incomplete knowledge. Probabilistic method can be applied to all of them, objective probability for random factors and subjective probability for the other two types of uncertain factors. Discrete subjective probability mass functions for incomplete and fuzzy factors can be obtained from logic-tree and membership functions respectively. Fractile curves may be used to show the scattering of any uncertainty factor, but a unified probabilistic treatment may be applied to any combination of all three types of uncertainty.     

Effect of precyclic loading on stress-corrosion-cracking initiation in an X-65 pipeline steel exposed to near-neutral pH soil environment

A study was carried out to understand the effect of precyclic loading on stress-corrosion-crack initiation in an X-65 pipeline steel exposed to a near-neutral-pH soil environment. The test specimens were precyclically loaded before corrosion exposure to represent a service history of up to about 20 years, depending on the severity of pressure fluctuation. Microcracks had initiated on the polished surface of the X-65 pipeline steel after long-time exposure at open-circuit potential (OCP) in a near-neutral-pH synthetic soil solution. These microcracks were mostly initiated from pits at metallurgical discontinuities such as grain boundaries, pearlitic colonies, and banded phases in the steel. Strong preferential dissolution was observed along planes of the banded structures in the steel. The selective corrosion attack at these metallurgical discontinuities is attributed to the galvanic nature of those areas to their neighbors. Cyclic loading prior to corrosion exposure had significant effects on microcrack initiation and propagation during subsequent corrosion exposure. Cyclic loading prior to corrosion exposure either reduced or increased the probability of crack initiation and the rate of crack propagation, depending upon the magnitude of the stress cycles. The largest reduction was seen at a peak cyclic stress of about 0.8 of the yield strength. This cyclic-loading-dependent cracking behavior might be related to the alteration of the substructures and the residual stress in the steel as a result of precyclic loading.