Evolution of maturity levels of the particle surface and bulk during soot growth and oxidation in a flame

We performed a study of the evolution of soot composition and fine structure, i.e., maturity level, in an atmospheric ethylene-air diffusion flame. We used laser-induced incandescence (LII) to provide information about maturity level of the bulk primary particle and X-ray photoelectron spectroscopy (XPS) to provide complementary information about particle-surface-maturity level. The results demonstrate that the bulk material and the particle surface evolve separately in the flame. Increased soot-maturity level is associated with increased long-range order of the particle fine structure. This increased order leads to an increase in the absorption cross-section in the visible and near-infrared and a shift of the absorption to longer wavelengths with increasing maturity level of the bulk particle. These trends result in a decrease in the dispersion exponent (?) and increase in the absorption cross-section scaling factor (?), as inferred from LII measurements. LII measurements demonstrate that bulk-maturity level increases with height-above-the-burner (HAB) until it reaches a plateau in the center of the flame at the maximum in the soot volume fraction. Bulk-maturity level only slightly decreases as soot is oxidized at larger HABs. Increased maturity level also leads to an increase in long-range sp² hybridization. XPS measurements of the sp²/defect ratio demonstrate an increase in soot surface-maturity level with increasing HAB, but the surface-maturity level increases more gradually with HAB than the bulk-maturity level. Whereas the bulk-fine-structure order decreases slightly in the oxidation region, the surface order decreases dramatically, indicating that oxidation occurs preferentially at the surface under these conditions.

Copyright © The Authors. Published with license by American Association for Aerosol Research     

Social influence during the initial phase of a fire evacuation—Analysis of evacuation experiments in a cinema theatre

Unannounced evacuation experiments in a cinema theatre were analysed. The analysis focused on investigating if people are influenced by others during the initial phase of a fire evacuation. This type of influence is called social influence. Three separate behaviour types were identified and studied and the recognition and pre-movement time was measured. The results suggest that social influence is an important factor and that it becomes more important when the fire cue, e.g., the alarm, is unclear or uninformative. Results also indicate that social influence increases with decreasing distance between visitors. This result implies that individuals are influenced more by people who are close than by people who are further away.     

Key technologies for IMT-advanced mobile communication systems

WINNER is an ambitious research project aiming at identification, development, and assessment of key technologies for IMTAdvanced mobile communication systems. WINNER has devised an OFDMA-based system concept with excellent system-level performance for flexible deployments in a wide variety of operating conditions. The WINNER system provides a significant step forward from current 3G systems. Key innovations integrated into the system concept include flexible spectrum usage and relaying, adaptive advanced antenna schemes and pilot design, close to optimal link adaptation, hierarchical control signaling, and a highly flexible multiple access scheme. The end-to-end performance assessment results demonstrate that the WINNER concept meets the IMTAdvanced requirements.     

Wideband Low‐Reflection Transmission Lines for Bare Chip on Multilayer PCB

The pad pitch of modern radio frequency integrated circuits is in the order of few tens of micrometers. Connecting a large number of high‐speed I/Os to the outside world with good signal fidelity at low cost is an extremely challenging task. To cope with this requirement, we need reflection‐free transmission lines from an on‐chip pad to on‐board SMA connectors. Such a transmission line is very hard to design due to the difference in on‐chip and on‐board feature size and the requirement for extremely large bandwidth. In this paper, we propose the use of narrow tracks close to chip and wide tracks away from the chip. This narrow‐to‐wide transition in width results in impedance discontinuity. A step change in substrate thickness is utilized to cancel the effect of the width discontinuity, thus achieving a reflection‐free microstrip. To verify the concept, several microstrips were designed on multilayer FR4 PCB without any additional manufacturing steps. The TDR measurements reveal that the impedance variation is less than 3 Ω for a 50 Ω microstrip and S11 better than –9 dB for the frequency range 1 GHz to 6 GHz when the width changes from 165 µm to 940 µm, and substrate thickness changes from 100 µm to 500 µm.     

Does sodium fluoride in bone cement affect implant fixation? Part I: Bone tissue response, implant fixation and histology in nine rabbits

The addition of sodium fluoride to poly (methyl-methacrylate) (PMMA) bone cement may theoretically improve the fixation of joint replacement. This hypothesis was tested in an animal model using nine mature healthy lop-eared rabbits. A femoral prosthesis was inserted in both knees to resurface the patellofemoral articulation. The same acrylic cement, with and without sodium fluoride, was randomised between the two sides for prosthetic fixation. Two screw shaped implants machined from cured rods of either cement were also inserted bilaterally into the proximal tibia. Qualitative and quantitative histomorphometry of the bone tissue response surrounding the cement in the femur and the intact tibial implants revealed similar results regardless of sodium fluoride addition. Six weeks after surgery removal, torque did not significantly differ between the two sides. Our findings indicate that addition of sodium fluoride to PMMA has little effect on implant stability and bone remodeling in rabbits in the short-term.     

Parallel flow measurements in microstructures by use of a multifocal 4 x 1 diffractive optical fan-out element

We have developed a multifocal optical fluorescence correlation spectroscopy system for parallel flow analyses. Multifocal excitation was made possible through a 4 x 1 diffractive optical fan-out element, which produces uniform intensity in all four foci. Autocorrelation flow analyses inside a 20 microm x 20 microm square microchannel, with the 4 x 1 fan-out foci perpendicular to the flow direction, made it possible to monitor different flows in all four foci simultaneously. We were able to perform cross-correlation flow analyses by turning the microstructure, thereby having all four foci parallel to the direction of flow. Transport effects of the diffusion as a function of flow and distance could then also be studied.     

Limit cycles with chattering in relay feedback systems

Relay feedback has a large variety of applications in control engineering. Several interesting phenomena occur in simple relay systems. In the paper, scalar linear systems with relay feedback are analyzed. It is shown that a limit cycle where part of the limit cycle consists of fast relay switchings can occur. This chattering is analyzed in detail and conditions for approximating it by a sliding mode are derived. A result on existence of limit cycles with chattering is given, and it is shown that the limit cycles can have arbitrarily many relay switchings each period. Limit cycles with regular sliding modes are also discussed. Examples illustrate the results.     

Light-scattering studies of packed stationary phases for capillary electrochromatography

Multiply scattered light through turbid media, packed particles, or compressed powders will inherently have a significantly longer optical path length than that of light which is not scattered. The concept of using the multiply scattered light potentially generated in the packed stationary phase of a capillary electrochromatography (CEC) column for enhanced detection as a result of its increased optical path length was examined. Ultraviolet (UV) light at 365 nm or laser light at 635 nm was focused to a small spot onto the packed section of a 3 microns spherisorb ODS1 CEC column (100 microns i.d.). The light was transported inside the capillary, and an image of the multiply scattered light several millimeters along the capillary was collected using a charged-couple device detector. Even if the spot size was less than 100 microns in diameter, evidence of light scattering was observed at a detection spatial off-set distance of 1-2 mm from the illumination point. When the calcium channel blocking drug felodipine was flushed through the column, the light intensity value dropped (increase in absorbance) to a greater degree at a spatial off-set (1.5 mm) than at the illumination point. The greater absorbance values at the spatial off-set were examined experimentally when felodipine was eluted from the column in the CEC mode in 6 min using MeCN/50 mM TRIS (pH 8.0) (80:20, v/v) at an applied voltage of 300 V/cm and an injection time of 2 s at 10 kV. A factor of 8.5 increase in absorbance was observed at a spatial off-set of 1 mm compared to the value obtained at the illumination point. An efficiency value of approximately 234,000 plates m-1 was obtained for this higher felodipine peak. Higher noise values, however, were also observed with this increase in absorbance. Using a spectrophotometer or an open capillary to obtain reference values for optical length, it was possible to estimate the average optical path length of light traveled through the packed stationary phase when transmitted at a spatial off-set. It was concluded that, although an increase in absorbance of 8.5 was observed at a spatial off-set, this most likely arises from the light being "redirected" and scattered in a straightforward fashion along the capillary. It was expected that if substantial multiple scattering did occur inside the packed stationary phase, a significantly larger absorbance increase would be attained. A number of proposals are thus given to explain the relatively low degree of multiple scattering in this stationary phase and suggestions offered on means to attain even higher absorbance increases at a spatial off-set. Additional potential applications are also discussed.     

Fabrication and simulation of diffractive optical elements with superimposed antireflection subwavelength gratings

With the aim of reducing surface reflections and increasing the diffraction efficiency we investigated the superposition of subwavelength phase gratings onto blazed phase gratings. With direct-write electron-beam lithography bare blazed gratings and blazed gratings carrying subwavelength gratings were fabricated and their optical performances compared. For TE polarization the subwavelength-carrying gratings showed a maximum diffraction efficiency of 90.6%, whereas the corresponding maximum value for the bare grating was 86.3%. The experiment was simulated with rigorous diffraction theory.