Injection-seeded Q-switched fiber ring laser

We present a narrow linewidth, injection-seeded Q-switched Er fiber ring oscillator, that provides over 600 /spl mu/W of average output power at 500 Hz, with 1.2 /spl mu/J per pulse, before the output appears to be significantly affected by stimulated Brillouin scattering. This laser configuration provides multiple advantages in LIDAR systems because it offers the possibility of broad and rapid tunability.     

Time-resolved spectroscopy of infrared active vibrations in 2,5-dioctyloxy poly(phenylene vinylene) films

We report on picosecond time resolved spectroscopy of photogenerated infrared active vibrations in thin films of 2,5-dioctyloxy poly(phenylene vinylene). We excited the films by ?4 ps long pulses of 565 nm laser light with 2×10¹³ photons/cm² per pulse and repetition rate of 76 MHz. We then followed the temporal evolution of the infrared active vibrational (IRAV) spectrum using a subsequent, variably delayed, weak tunable IR probe pulses of similar temporal duration. Under these conditions, we show clear spectroscopic evidence for photogenerated infrared active vibrations at times which are shorter than our temporal resolution (<4 ps). We suggest that the transient IRAV absorption is due to secondary polarons formation following exciton dissociation.     

A 0.18-/spl mu/m SiGe BiCMOS receiver and transmitter chipset for SONET OC-768 transmission systems

A 43-Gb/s receiver (Rx) and transmitter (Tx) chip set for SONET OC-768 transmission systems is reported. Both ICs are implemented in a 0.18-/spl mu/m SiGe BiCMOS technology featuring 120-GHz f/sub T/ and 100 GHz f/sub max/. The Rx includes a limiting amplifier, a half-rate clock and data recovery unit, a 1:4 demultiplexer, a frequency acquisition aid, and a frequency lock detector. Input sensitivity for a bit-error rate less than 10/sup -9/ is 40 mV and jitter generation better than 230 fs rms. The IC dissipates 2.4 W from a -3.6-V supply voltage. The Tx integrates a half-rate clock multiplier unit with a 4:1 multiplexer. Measured clock jitter generation is better than 170 fs rms. The IC consumes 2.3 W from a -3.6-V supply voltage.     

Bandwidth of reflectarrays

It is shown that the dominant factor controlling reflectarray bandwidth is the bandwidth of the radiating element, and that the effect of non-constant path delays over the surface of the flat reflector has little significance unless the aperture is electrically very large and the f/D ratio is small. An example of a polarisation-twist reflectarray using aperture coupled elements with time delay lines is used to demonstrate this conclusion.     

Design principles underlying circadian clocks.

A fundamental problem for regulatory networks is to understand the relation between form and function: to uncover the underlying design principles of the network. Circadian clocks present a particularly interesting instance, as recent work has shown that they have complex structures involving multiple interconnected feedback loops with both positive and negative feedback. While several authors have speculated on the reasons for this, a convincing explanation is still lacking.We analyse both the flexibility of clock networks and the relationships between various desirable properties such as robust entrainment, temperature compensation, and stability to environmental variations and parameter fluctuations. We use this to argue that the complexity provides the flexibility necessary to simultaneously attain multiple key properties of circadian clocks. As part of our analysis we show how to quantify the key evolutionary aims using infinitesimal response curves, a tool that we believe will be of general utility in the analysis of regulatory networks. Our results suggest that regulatory and signalling networks might be much less flexible and of lower dimension than their apparent complexity would suggest.     

Adaptive antenna system design for multi-element combining with transient interrupted channels

This paper presents an analysis and design procedure for a buoyant cable array antenna used for satellite communications. The towed multi-element array is susceptible to washovers and fluctuations due to the ocean wave interaction with the floating hose where the elements are housed. A model of system performance for coherent multi-element combining is presented based on the dropouts and fades of the individual elements. The array design, including the number and spacing of elements, is shown to be highly dependent on the individual element exposure characteristics and the degree of correlation of the fades between channels. The joint statistics of the array are analyzed using a binary conditional element exposure model and a first-order Markov interelement correlation model. Using this analysis, a family of array designs meeting the communications requirements is produced.     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

Quantisation noise control in perceptual audio coding using low selectivity filter banks

The problem of computing, in a subband audio coder, the maximum quantisation noise power that can be injected in each band to ensure transparent coding when low selectivity filter banks are used, is addressed. A low complexity strategy, taking into account the frequency responses of the synthesis filter bank, is proposed for achieving an overall distortion due to quantisation noise always below the masking threshold (provided by a psycho-acoustic model) for any length prototype filters.     

Near-field corrections to site attenuation

The theoretical model used for calculating normalized site attenuation for broadband antennas in ANSI C63.4-1992 and for antenna calibration in ANSI C63.5-1988 includes only the radiation terms in the electric field. The omission of the near field terms leads to errors of as much as 2.0 dB at 30 MHz for horizontally polarized antennas separated by 3 m. Corrected values of normalized site attenuation and E _D^max are presented for the 30-300 MHz frequency range