A 1.5-V 45-mW direct-conversion WCDMA receiver IC in 0.13-/spl mu/m CMOS

A 2-GHz direct-conversion receiver for wide-band code division multiple access (WCDMA) is presented. It includes two low-noise amplifiers (LNAs), an I/Q demodulator, and two sixth-order baseband channel select filters with programmable gain. Quadrature local oscillator (LO) signals are generated on chip in a frequency divider flip-flop. An external interstage filter between the LNAs rejects transmitter leakage to relax demodulator linearity requirements. A low-voltage demodulator topology improves linearity as well as demodulator output pole accuracy. The active-RC baseband filter uses a programmable servo loop for offset compensation and provides an adjacent channel rejection of 39 dB. Programmable gain over 71-dB range in 1-dB steps is merged with the filter to maximize dynamic range. An automatic on-chip frequency calibration scheme provides better than 1.5% corner frequency accuracy. The receiver is integrated in a 0.13-/spl mu/m CMOS process with metal-insulator-metal (MIM) capacitors. Measured receiver performance includes a 6.5-dB noise figure, IIP2 of +27 dBm, and IIP3 of -8.6 dBm. Power consumption is 45 mW.     

Oxidative degradation of polyamide reverse osmosis membranes: Studies of molecular model compounds and selected membranes

Selected aromatic amides were used to model the chemical reactivity of aromatic polyamides found in thin‐film composite reverse osmosis (RO) membranes. Chlorination and possible amide bond cleavage of aromatic amides upon exposure to aqueous chlorine, which can lead to membrane failure, were investigated. Correlations are made of the available chlorine concentration, pH, and exposure time with chemical changes in the model compounds. From the observed reactivity trends, insights are obtained into the mechanism of RO membrane performance loss upon chlorine exposure. Two chemical pathways for degradation are shown, one at constant pH and another that is pH‐history dependent. An alternative strategy is presented for the design of chlorine‐resistant RO membranes, and an initial performance study of RO membranes incorporating this strategy is reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1173–1184, 2003     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

Effect of film thickness on hydrogen content in a-Si : H

The hydrogen content, its depth distribution, and its bonding configuration have been studied in hydrogenated amorphous silicon prepared by plasma-enhanced chemical vapor deposition with hydrogen-diluted silane. Nuclear reaction analysis and infrared spectroscopy were used to determine the total amount of hydrogen and its bonded component, respectively. It has been established that the total concentration of hydrogen does not depend on the film thickness, and has a uniform depth profile. The concentration of bonded hydrogen changes with the film thickness within the measurement accuracy. The data obtained suggest the presence of molecular (non-bonded) hydrogen, uniformly distributed in concentration across the film thickness.     

Lateral ion implant straggle and mask proximity effect

Lateral scattering of retrograde well implants is shown to have an effect on the threshold voltage of nearby devices. The threshold voltage of both NMOSFETs and PMOSFETs increases in magnitude for conventional retrograde wells, but for triple-well isolated NMOSFETs the threshold voltage decreases for narrow devices near the edge of the well. Electrical data, SIMS, and SUPREM4 simulations are shown that elucidate the phenomenon.     

Operating Penalties in Single-Fiber Operation 10-Gb/s, 1024-Way Split, 110-km Long-Reach Optical Access Networks

We report for the first time optical signal-to-noise penalties which lead to performance degradations in single-fiber long-reach optical access networks when compared to identical dual-fiber systems. A simplified architecture, with reduced optical amplifier count compared to previous work, for single-fiber operation of a symmetrical 10-Gb/s, 1024-way split, 110-km long-reach optical access network is presented and demonstrated. In addition, a possible solution to remove the optical signal-to-noise penalty is suggested     

A decision support system for interactive decision making - Part II: analysis and output interpretation

For pt.I see ibid., p.42-55 (2003). The development of a comprehensive decision support system, GMCR II, for the systematic study of real-world interactive decision problems is presented. The companion paper (Part I), discusses how GMCR II elicits, stores, and manages conflict models; here (Part II), the focus is on GMCR IIs analysis and output interpretation subsystems. Specifically, this paper describes the powerful and efficient analysis engine contained in GMCR II, its informative output presentation and interpretation facilities, and a number of follow-up analyses. Furthermore, an illustrative case study is used to demonstrate how GMCR II can be conveniently applied in practice.     

Graphitization of porous 6H-SiC layers during thermal treatment in vacuum

We have studied the effect of thermal treatment in vacuum on the optical transmission of 6H-SiC samples with a porous layer on the Si face in the visible and near infrared spectral range. An analysis of changes in the absorption coefficient shows that the process of graphitization begins at a temperature below 70°C.