A 300-MHz 25-/spl mu/A/Mb-leakage on-chip SRAM module featuring process-variation immunity and low-leakage-active mode for mobile-phone application processor

An on-chip 1-Mb SRAM suitable for embedding in the application processor used in mobile cellular phones was developed. This SRAM supports three operating modes - high-speed active mode, low-leakage low-speed active mode, and standby mode - and uses a subdivisional power-line control (SPC) scheme. The combination of three operating modes and the SPC scheme realizes low-power operation under actual usage conditions. It operates at 300 MHz, with leakage of 25 /spl mu/A/Mb in standby mode, and 50 /spl mu/A/Mb at the low-leakage active mode. This SRAM also uses a self-bias write scheme that decreases of minimum operating voltage by about 100 mV.     

End-to-End QoS for Video Delivery Over Wireless Internet

Providing end-to-end quality of service (QoS) support is essential for video delivery over the next-generation wireless Internet. We address several key elements in the end-to-end QoS support, including scalable video representation, network-aware end system, and network QoS provisioning. There are generally two approaches in QoS support: the network-centric and the end-system centric solutions. The fundamental problem in a network-centric solution is how to map QoS criterion at different layers respectively, and optimize total quality across these layers. We first present the general framework of a cross-layer network-centric solution, and then describe the recent advances in network modeling, QoS mapping, and QoS adaptation. The key targets in end-system centric approach are network adaptation and media adaptation. We present a general framework of the end-system centric solution and investigate the recent developments. Specifically, for network adaptation, we review the available bandwidth estimation and efficient video transport protocol; for media adaptation , we describe the advances in error control, power control, and corresponding bit allocation. Finally, we highlight several advanced research directions.     

软β核素内部样品塑料闪烁探测器

本文评价了塑料闪烁片用作软β核素探测器时的计数效率、β谱、本底谱和康普顿电子谱的特征。文中强调:采用胶合光导剂构成的系统是一种新型探测器(软β核素内部样品塑料闪烁探测器)。本文提出内部样品固体探测器、胶合光导剂和胶合闪烁光导剂的新概念。     

The microstructures of laser-alloyed Ni-Ta surface layers

Evaporated thin tantalum films on single and polycrystalline nickel have been laser surface alloyed using either continuous-wave CO₂ or Q-switched Nd-YAG radiation. In the case of the continuous-wave laser, surface alloys contain amorphous tantalum-rich regions, intermediate polycrystalline bands of TaNi, and an underlying Ni(Ta) solid solution. In the Q-switched laser case, a much more laterally uniform amorphous phase with approximately equal atomic fractions of nickel and tantalum is found, with little evidence of polycrystalline intermetallics.In situ annealing with the electron beam of the microscope results in formation of microcrystallites, predominantly nickel.     

Quantitative determination of aflatoxin B1 in chick liver

A method for the rapid and quantitative determination of aflatoxin B1 from small quantities of liver, around 1-2 g, is described. The extraction procedure involves acidification to pH 2 of the aqueous liver homogenates, extraction with chloroform: acetone and HPLC-fluorimetric detection after derivatization with trifluoroacetic acid. Quantitative recovery of aflatoxin B1 from chick liver was achieved and detection at levels of 0.2-1 ppb was proved feasible. The aflatoxin B1 concentration in chick liver after oral administration is also shown.     

Extremely low-loss 1.5%-/spl Delta/ 32-channel athermal arrayed-waveguide grating multi/demultiplexer

A silica-based 1.5%-/spl Delta/ 100 GHz-spacing 32-channel athermal arrayed-waveguide grating (AWG) with compact size and extremely low insertion loss is described. By reducing the fibre coupling loss and the excess loss in a silicone-filled groove, an insertion loss of 1.3 dB was achieved with this athermal AWG.     

Minimum-energy multicast in mobile ad hoc networks using network coding

The minimum energy required to transmit one bit of information through a network characterizes the most economical way to communicate in a network. In this paper, we show that, under a layered model of wireless networks, the minimum energy-per-bit for multicasting in a mobile ad hoc network can be found by a linear program; the minimum energy-per-bit can be attained by performing network coding. Compared with conventional routing solutions, network coding not only allows a potentially lower energy-per-bit to be achieved, but also enables the optimal solution to be found in polynomial time, in sharp contrast with the NP-hardness of constructing the minimum-energy multicast tree as the optimal routing solution. We further show that the minimum energy multicast formulation is equivalent to a cost minimization with linear edge-based pricing, where the edge prices are the energy-per-bits of the corresponding physical broadcast links. This paper also investigates minimum energy multicasting with routing. Due to the linearity of the pricing scheme, the minimum energy-per-bit for routing is achievable by using a single distribution tree. A characterization of the admissible rate region for routing with a single tree is presented. The minimum energy-per-bit for multicasting with routing is found by an integer linear program. We show that the relaxation of this integer linear program, studied earlier in the Steiner tree literature, can now be interpreted as the optimization for minimum energy multicasting with network coding. In short, this paper presents a unifying study of minimum energy multicasting with network coding and routing.     

Continuous-wave lasing of single-mode metamorphic quantum dot lasers for the 1.5-μm spectral region

Lasers based on InAs/InGaAs quantum dots grown on metamorphic (In,Ga,Al)As layers deposited by MBE on GaAs substrates exhibited emission near 1.5 μm with a differential quantum efficiency of about 50%. The narrow-stripe lasers operate in a single transverse mode and withstand continuous current density above 20 kA cm^?2 without significant degradation. A maximum continuous-wave output power of 220 mW is obtained. Neither current nor beam filamentation was observed up to the highest pumping levels.     

Evaluating the application of a decision support system in identifying adequate wastewater treatment for small communities. A case study: the Fluvia River Basin.

The identification of adequate wastewater treatment for small communities is a complex problem since it demands a combination of data from different sources, such as aspects of the community and landscape, the receiving environment and the available wastewater treatment technologies. The Catalan Water Agency (Agència Catalana de l'Aigua) considered using an EDSS (Environmental Decision Support System) as a tool to help water managers select the most adequate treatment for the urban wastewater of nearly 3,500 small communities in Catalonia (Spain). From that moment, EDSS was applied to all the river basins in Catalonia. In this paper the authors present the results obtained for the 76 small communities located in one of these river basins: the Fluvia River Basin. The characteristics of the community used in the reasoning process of the EDSS, the list of selected wastewater treatment alternatives, the technical environmental justification for the selected treatments and the reasons for discarding, favouring or disadvantaging them are presented. Finally, some results for the Fluvia River Basin are compared with those obtained in other Catalan river basins with different characteristics in order to evaluate which are the significant features in identifying adequate wastewater treatments.