Surface analysis using a new plasma assisted desorption/ionisation source for mass spectrometry in ambient air

The authors report on a modified micro-plasma assisted desorption/ionisation (PADI) device which creates plasma through the breakdown of ambient air rather than utilising an independent noble gas flow. This new micro-PADI device is used as an ion source for ambient mass spectrometry to analyse species released from the surfaces of polytetrafluoroethylene, and generic ibuprofen and paracetamol tablets through remote activation of the surface by the plasma. The mass spectra from these surfaces compare favourably to those produced by a PADI device constructed using an earlier design and confirm that the new ion source is an effective device which can be used to achieve ambient mass spectrometry with improved spatial resolution.     

Measurement sensitivity improvement in tapping-mode atomic force microscopy through bi-harmonic drive signal

This article presents a novel method to improve the measurement sensitivity and reduce impact forces in tapping-mode atomic force microscopy by reshaping the tip trajectory. A tapping drive signal composed of two harmonics is used to generate an oscillating trajectory with a broader valley compared to the typical sinusoidal trajectory. The wide broad valley reduces the velocity of the tip in the vicinity of the sample and allots a greater portion of each period in the vicinity of the sample. Numerical simulations show that this results in decreased impact force and increased sensitivity of the cantilever oscillation to changes in tip-sample offset. Experimental results demonstrate an increase in image sharpness and decrease in tip wear using the bi-harmonic driving signal.     

COBRA-STAR, a five frame point-projection x-ray imaging system for 1 MA scale wire-array Z pinches

A new imaging system for 1 MA scale wire-array Z-pinch experiments that produces up to five high-resolution x-ray images per experimental pulse has been developed. Calibrated areal density measurements of the Z-pinch plasma can be obtained from each pulse. The system substitutes five molybdenum (Mo) X pinches for the normal copper return-current conductors to provide point sources of x-rays for point-projection radiography. Each backlighting X pinch consists of four Mo wires, the x-ray burst timing of which was controlled by varying the wire diameter (mass) from 10.2 to 30 microm in the five X pinches. Typical images have a 16x8 mm2 field of view at the wire array and a magnification of about 6.5:1 on the x-ray-sensitive film. Titanium (Ti) filters in front of the films transmit continuum radiation in the spectral range of 3-5 keV. Inclusion on the Ti of a step wedge having known thickness increments of the same material as the wires enables the calibrated areal density measurements to be made of the exploding wire plasmas. Here, we used tungsten (W) step wedges with step thicknesses ranging from 0.015 to 1.1 microm to obtain accurate (+/-10%) areal density measurements of W plasmas from the spatial profile of film exposure. When imaging arrays that produce intense radiation pulses, a plastic monofilament "quencher" is placed on axis to avoid film saturation. Images have subnanosecond temporal resolution and about 7 microm spatial resolution.     

Improvements in planar feature reconstructions in atom probe tomography

Standard atom probe tomography spatial reconstruction techniques have been reasonably successful in reproducing single crystal datasets. However, artefacts persist in the reconstructions that can be attributed to the incorrect assumption of a spherical evaporation surface. Using simulated and experimental field evaporation, we examine the expected shape of the evaporating surface and propose the use of a variable point projection position to mitigate to some degree these reconstruction artefacts. We show initial results from an implementation of a variable projection position, illustrating the effect on simulated and experimental data, while still maintaining a spherical projection surface. Specimen shapes during evaporation of model structures with interfaces between regions of low- and high-evaporation-field material are presented. Use of two-and three-dimensional projection-point maps in the reconstruction of more complicated datasets is discussed.     

Subtleties in ADF imaging and spatially resolved EELS: A case study of low-angle twist boundaries in SrTiO3

A screw dislocation network at the low-angle SrTiO3/Nb:SrTiO3 twist grain boundary has been analyzed by annular dark field (ADF) imaging and spatially resolved electron energy loss spectroscopy (EELS) in a scanning transmission electron microscope (STEM). The cores of one set of dislocations running parallel to the beam direction appear dark in the ADF STEM images. EELS on the dislocation core reveals a reduced Sr/Ti ratio compared to the bulk suggesting Sr-deficient cores. The second set of dislocations, orthogonal to the latter, is imaged by its strain field using low-angle annular dark field (LAADF) imaging. Multislice image simulations suggest channeling of the electron probe on the atomic columns for small tilts, theta < 1 degree, where the Sr columns act as beam guides. Only for larger tilts is the channeling effect strongly reduced and the fringe contrast approaches the value predicted by a purely incoherent imaging model. Ti-L(2,3) EELS across the dislocation core shows an asymmetry between the EELS and the ADF signal which cannot be explained by the geometry or beam broadening. This asymmetry might be explained by an effective nonlocal potential representing inelastic scattering in EELS.     

Adsorption of beta blockers to environmental surfaces

Beta-adrenergic blocking agents (beta blockers) are widely used pharmaceuticals which have been detected in the environment. Predicting the transport and ultimate fate of beta blockers in the environment requires understanding their adsorption to soils and sediments, something for which little information is currently available. The objective of this work was to examine the adsorption of three beta blockers, propranolol, metoprolol and nadolol, to a natural alluvial material, as well as to six minerals present as components of the alluvial material. Batch adsorption experiments indicate that, for most of the minerals studied, compound hydrophobicity is an important predictor of adsorption, with propranolol,the most hydrophobic compound studied, adsorbing to the greatest extent. Results further suggest that, for the minerals studied, electrostatic effects are not a good predictor of adsorption; adsorption extent was not well-predicted by either surface zeta potential or by the difference between experiment pH and point of zero charge, despite the cationic nature af the three beta blockers at experiment pH values. Experiments were conducted to examine the effect of an anionic surfactant, sodium dodecyl benzene sulfonate (SDBS), on adsorption. Results indicate that SDBS significantly increases the adsorption of propranolol to two different sorbents. This result is potentially important because surfactants such as SDBS are likely to be present in wastewater effluents with beta blockers and could influence their mobility in the environment.     

Spectroscopic study of carbaryl sorption on smectite from aqueous suspension

Sorption of carbaryl (1-naphthyl-N-methyl-carbamate) from aqueous suspension to smectite was studied using Fourier transform infrared (FTIR), high-performance liquid chromatography (HPLC) (for batch sorption), and quantum chemical methods. The amount of carbaryl sorbed was strongly dependent on the surface-charge density of the smectite with more sorption occurring on the two "low" surface-charge density smectites (SHCa-1 and SWy-2) compared to that of the high surface-charge SAz-1 smectite. In addition, the amount of carbaryl sorbed was strongly dependent on the nature of the exchangeable cation and followed the order of Ba approximately Cs approximately Ca > Mg approximately K > Na approximately Li for SWy-2. A similartrend was found for hectorite (SHCa-1) of Cs > Ba > Ca > K approximately Mg > Na approximately Li. Using the shift of the carbonyl stretching band as an indicator of the strength of interaction between carbaryl and the exchangeable cation, the observed order was Mg > Ca > Ba approximately K > Na > Cs. The position of the carbonyl stretching band shifted to lower wavenumbers with increasing ionic potential of the exchangeable cation. Density functional theory predicted a cation-induced lengthening of the C=O bond, resulting from the carbonyl group interacting directly with the exchangeable cation in support of the spectroscopic observations. Further evidence was provided by a concomitant shift in the opposite direction by several vibrational bands in the 1355-1375 cm(-1) region assigned to stretching bands of the carbamate N-Ccarbonyl and Oether-Ccarbonyl bonds. These data indicate that carbaryl sorption is due, in part, to site-specific interactions between the carbamate functional group and exchangeable cations, as evidenced by the FTIR data. However, these data suggest that hydrophobic interactions also contribute to the overall amount of carbaryl sorbed. For example, the FTIR data indicated thatthe weakest interaction occurred when Cs+ was the exchangeable cation. In contrast, the highest amount of carbaryl sorption was observed on Cs-exchanged smectite. Of all the cations studied, Cs has the lowest enthalpy of hydration. It is suggested that this low hydration energy provides the carbaryl with greater access to the hydrophobic regions of the siloxane surface.     

交流同步起动发电机在变频起动中机械特性的分析与计算

立足于铁道部正在研制的第一台交流传动内燃调车机车,在已设计的同步起动发电机参数的基础上,结合变频起动装置的工作原理,分析并计算该起动发电机在起动过程中的机械特性。     

Microbiological quality of sausages containing chickpea flour (Cicer arietinum)

English-type fresh skinless pork sausages in which 30% of the protein was replaced by unheated chickpea flour or by chickpea flour heated at 80°C for 1 h were evaluated microbiologically. During storage at 0°C, but not 22°C, incorporation of unheated chickpea flour lowered the microbiological quality of the sausages, but incorporation of chickpea flour previously heated at 80°C for 1 h led to no less of microbiological quality.