Efficient Generation of Scalable Transport Stream for High Quality Service in T‐DMB

We introduce an advanced terrestrial digital multimedia broadcasting (AT‐DMB) system that overcomes the limitation of data transmission rates of T‐DMB by doubling it with the same frequency bandwidth. In this letter, we propose an efficient algorithm which generates a scalable transport stream in AT‐DMB by multiplexing certain types of elementary streams encoded using scalable video coding and an MPEG‐surround audio coder for high‐quality multimedia services.     

Low‐Power 512‐Bit EEPROM Designed for UHF RFID Tag Chip

In this paper, the design of a low‐power 512‐bit synchronous EEPROM for a passive UHF RFID tag chip is presented. We apply low‐power schemes, such as dual power supply voltage (VDD=1.5 V and VDDP=2.5 V), clocked inverter sensing, voltage‐up converter, I/O interface, and Dickson charge pump using Schottky diode. An EEPROM is fabricated with the 0.25 μm EEPROM process. Power dissipation is 32.78 μW in the read cycle and 78.05 μW in the write cycle. The layout size is 449.3 μm × 480.67 μm.     

Writing current reduction and total set resistance analysis in PRAM

We evaluated the limit of scaling bottom electrode contact (BEC) heater size and high resistivity heater to reduce writing current. It was found that the resistivity of heater should be increased for reducing writing current below the heater size of about 50 nm without any undesirable increase of resistance of the crystalline state (SET state, Rset). It was shown in the numerical simulations that the dissipated heat loss through BEC during melting GST was decreased in the increase of resistivity of heater. In addition, we analyzed the resistance components contributing to the total set resistance. It was observed that the undesired sharp increase of Rset as the BEC size decreases below 50 nm was attributed to the resistance component of GST–BEC interface. In the case of high resistivity heater, the contributions of both incomplete crystallization and heater itself were enhanced.     

Power law behavior of magnetoresistance in tris(8-hydroxyquinolinato)aluminum-based organic light-emitting diodes

Long-term current drift and dielectric relaxation in organic thin films of a single-layer structure pose a serious problem for the accurate measurement of magnetoresistance at low magnetic fields. A new measurement scheme was devised to minimize errors and to report that the magnetoresistance in tris(8-hydroxyquinolinato)aluminum obeys a power law on the magnetic field at 300, 100, and 4.2 K in an entire range from 1 to 140 mT. The exponent of the power increases gradually from 0.47 for a bias voltage of 3 V to 0.58 for a bias voltage of 8 V. The magnetoresistance was observable above the threshold voltage only and its sign was always negative.     

Octupolar Films with Large Second Harmonic Generation and Electro‐Optical Effects

Thin films that benefit from efficient octupolar molecular packing are prepared for second harmonic generation (SHG) and electro‐optic (EO) applications. The films are composed of 1,3,5‐tricyano‐2, 4,6‐tris(p‐diethylaminostyryl)benzene (TTB) in a ploymethylmetacrylate (PMMA) matrix on aluminum/BK7 glass (Al/BK7) and polyimide/indium tin oxide (PI/ITO) substrates. Octupolar films prepared on both substrates display polycrystalline and cylindrical domains. The molecular orientation, SHG efficiencies, and EO coefficients of the crystalline domains are measured. In the cylinders, the molecular crystal planes are oriented perpendicularly to the major cylinder axis, whereas in the polycrystals, the planes are randomly oriented. While both structures exhibit high and stable SHG and EO efficiencies, the cylinders, in particular, exhibited a very large SHG, a large EO coefficient, and high thermal stability; these characteristics will be useful in second order nonlinear optical applications.     

Virtual-node-based multicast routing and wavelength assignment in sparse-splitting optical networks

This paper investigates several problems associated with optical multicast routing and wavelength assignment in sparse-splitting optical networks for interactive real-time media distribution. Unfortunately, the constrained multicast routing with optimized wavelength assignment leads to NP-complete condition. Thus, in this paper, a virtual-node-based multicast routing algorithm is first proposed to satisfy the requirements of interactive real-time multicasting as well as the constraints from underlying optical networks. For the constructed multicast tree, we then associate an effective wavelength assignment algorithm. The experimental results show that the proposed algorithm combination performs well in terms of (1) the wavelength channel cost, (2) the maximum variation of inter-destination node delays, (3) the signal quality, and (4) the number of wavelength conversions.     

Instruction‐Level Power Estimator for Sensor Networks

In sensor networks, analyzing power consumption before actual deployment is crucial for maximizing service lifetime. This paper proposes an instruction‐level power estimator (IPEN) for sensor networks. IPEN is an accurate and fine grain power estimation tool, using an instruction‐level simulator. It is independent of the operating system, so many different kinds of sensor node software can be simulated for estimation. We have developed the power model of a Micaz‐compatible mote. The power consumption of the ATmega128L microcontroller is modeled with the base energy cost and the instruction overheads. The CC2420 communication component and other peripherals are modeled according to their operation states. The energy consumption estimation module profiles peripheral accesses and function calls while an application is running. IPEN has shown excellent power estimation accuracy, with less than 5% estimation error compared to real sensor network implementation. With IPEN's high precision instruction‐level energy prediction, users can accurately estimate a sensor network's energy consumption and achieve fine‐grained optimization of their software.     

Intelligent process analytics for CRM

Many organisations use decision models in their processes such as tables or trees to provide decision support to their operational divisions. For example, in fault management, customer contact centre operators usually use a decision model in the form of prescribed interviews. Based on the answers given by customers, the operator navigates through the decision model to reach an assessment of the problem. In order to achieve customer satisfaction and operational excellence, it is very important to constantly monitor the performance of a decision model not only on an overall level, but also on the level of individual decisions. In this paper we present a configurable business process analytics tool, known as the intelligent Universal Service Management System, that constantly monitors decision data and is capable of optimising the decisions based on high-level business objectives. We explain the various features of the software and show how it can be used to optimise decision processes. We also show how we can easily provide a customised version to monitor the performance of provision processes.     

Design of flexible GF(2/sup m/) elliptic curve cryptography processors

The design of flexible elliptic curve cryptography processors (ECP) is considered in this paper. Novel word-level algorithms and implementations for the underlying GF(2/sup m/) multiplication and squaring arithmetic which enable improved flexibility versus performance tradeoffs, are presented and employed in the design of an efficient flexible ECP architecture; corresponding field-programmable gate-array (FPGA) prototyping results for two different processor word lengths are also included for evaluation.