An artificial neural network approach on parametric optimization of laser micro-machining of die-steel

In the present research, laser micro machining (LMM) of tungsten-molybdenum general purpose high speed steel (Rex M2) has been studied. Selection of optimum machining parameter combinations for obtaining higher depth of groove and smaller height of recast layer is a challenging task in LMM due to the presence of a large number of process variables. There is no perfect combination of parameters which can simultaneously result in both the highest depth of groove and lowest height of recast layer. This paper presents an attempt to develop a strategy for predicting the optimum machining parameter setting for the generation of the maximum depth of groove with minimum height of recast layer. A feed forward back-propagation neural network has been developed to model the machining process. The model, after proper training, is capable of predicting the response parameters as a function of four different control parameters. Experimental results demonstrate that the machining model is suitable and the optimization strategy satisfies practical requirements. The developed model has been found to be quite unique, powerful and flexible.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Prony-Based Optimal Bayes Fault Classification of Overcurrent Protection

The development of deregulation and demand for high-quality electrical energy has lead to a new requirement in different fields of power systems. In the protection field, this means that high sensitivity and fast operation during the fault are required while maltripping of relay protection is not acceptable. One case that may lead to a maltrip of the high-sensitive overcurrent relay is the starting current of the induction motor or inrush current of the transformer. This transient current has the potential to affect the correct operation of protection relays close to the component being switched. In the case of switching events, such transients must not lead to overcurrent relay operation; therefore, a reliable and secure relay response becomes a critical matter. Meanwhile, proper techniques must be used to prevent maltripping of such relays, due to transient currents in the network. In this paper, the optimal Bayes classifier is utilized to develop a method for discriminating the fault from nonfault events. The proposed method has been designed based on extracting the modal parameters of the current waveform using the Prony method. By feeding the fundamental frequency damping and ratio of the 2nd harmonic amplitude over the fundamental harmonic amplitude to the classifier, the fault case is discriminated from the switching case. The suitable performance of this algorithm is demonstrated by simulation of different faults and switching conditions on a power system using PSCAD/EMTDC software.     

Influence of inhibitor addition on the corrosion protection performance of sol–gel coatings on AA2024

Sol–gel films are actively investigated during the last decade as possible candidates for environmentally friendly pre-treatments. However, the important drawback in this case is the lack of active corrosion protection and self-healing ability.     

Physico-chemical properties of ceramic pigments for high-temperature application

Heat resistant coatings are required primarily for stacks, exhaust pipes, reactors, space crafts and similar equipments that are permanently or occasionally exposed to elevated temperatures. High-temperature coatings are generally based on silicone resin with ceramic and metallic pigments. In this study, iron oxide, cobalt oxide (thermo chromic compound) and aluminum oxide are used for the preparation of four new types of coloured pigments. The thermal resistant characteristics of these ceramic pigments were studied by differential thermal analysis, thermo gravimetric analysis and differential scanning calorimetric analysis. These ceramic pigments are found to be thermally stable up to 400 °C.     

The Clausius inequality corrected for heat transfer involving radiation

The objective of this paper is to prove that the Clausius inequality must be re-stated to have general applicability for heat transfer involving radiative fluxes. The integrand (đQ/T) of the Clausius expression applies to heat conduction and convection, but does not hold for most radiative transfer scenarios, with the exception of reversible infinitesimal net blackbody radiation transfer. In other cases involving radiative transfer, the equality holds for a cycle even though irreversible heat addition by radiative transfer occurs. This is without the erroneous presumption of entropy destruction anywhere in the cycle. Thus, the Clausius inequality indicates reversibility for a cycle that includes an irreversible process. Further, in some radiative cases the quantity đQ/T, where T is the boundary temperature, is not the entropy transfer at the system boundary, and in fact, primarily represents entropy production within the system. It is also clear that in another case considered, the quantity đQ/T had no physical meaning whatsoever. Consequently, the Clausius expression has been re-stated so that it is applicable to cycles with processes involving any form of heat transfer. A new integrand (đQ_cc/T + đS_Net,Rad) is presented, allowing the Clausius inequality to generally apply to all heat transfer scenarios. The work in this paper emphasizes the need to re-state other fundamental equations allowing applicability to all heat transfer processes, and draws attention to the unique character of radiative entropy calculations.     

Selective Transport of Bismuth Ions through Supported Liquid Membrane

A new supported liquid membrane (SLM) system was prepared for the selective transport of bismuth ions from the aqueous feed into the aqueous permeate phase. The support of the SLM was a thin porous polypropylene or polyvinylidene fluoride membrane impregnated with diisooctyldithiophosphinic acid (Cyanex 301) as mobile carrier in 4‐chloroacetophenon as organic solvent. Cyanex 301 acts as a highly selective carrier for the uphill transport of bismuth ions through the SLM. In the presence of HNO₃ as a metal ion acceptor in the strip solution, the transport of bismuth ions into the strip side reached 70 % of the initial feed concentration after 3.5 hours. The selectivity and efficiency of bismuth transport from aqueous solutions containing different mixtures of cations were investigated. In the presence of P₂O₇^2– ions as suitable masking agent in the feed solution, the interfering effects of other cations were completely eliminated. The selective transport of bismuth through SLM is superior to liquid‐liquid extraction or through bulk liquid membranes. This is due to the high efficiency. The SLM reduces the solvent requirements, combines extraction and stripping operations in a single process and allows the use of highly selective extractants. The system may be applied to samples containing very low bismuth concentrations.     

Gasification of Biogenic Solid Fuels

As a result of shrinking fossil fuels, biomass as a regenerative energy source gains importance. To realize biomass projects it is essential to investigate in convenient thermal procedures. On this evidence an analysis and evaluation of diverse gasification technologies with different boundary conditions and diverse biomasses are indispensable. Form and kind of the biomass as well as the type of the gasification plant cause different compositions of the product gas. The gasifiers show advantages and disadvantages concerning the biomass and the produced gas quality, depending on reactor type, kind of heat supply, gasification medium, and the pressure ratio in the reactor. As the ideal gasifier for different biomass is presently not available, it will be shown, which biomass is suitable for fixed bed or fluidized bed gasifiers.