Characterization of dibromopolychlorodibenzo-p-dioxins and dibromopolychlorodibenzofurans in municipal waste incinerator fly ash using gas chromatography/mass spectrometry.

Several fly ash samples from different countries were analyzed for dibromopolychlorodibenzo-p-dioxins and -dibenzofurans (DBPCDD/Fs) using capillary column gas chromatography/high-resolution mass spectrometry. Concentrations of these compounds ranged from low to high parts-per-trillion (pptr) depending on the location where the samples were collected. The mass spectrometer, operated at greater than 10,000 mass resolution in combination with the high resolving power of capillary column GC, permitted characterization of DBPCDD/Fs in municipal waste incinerator fly ash for the first time. The isomer patterns of tetra- through octa-congener groups of DBPCDD/Fs are remarkably similar regardless of where the fly ash originated, indicating common mechanisms of formation of these compounds in the incinerators.     

淀积条件对GDa—SiNx薄膜电学特性的影响

本文讨论了用辉光放电法制备氮化硅薄膜时衬底温度、射频功率和气体流量比对薄膜的电导率、介电常数和击穿强度的影响。通过优化生长条件，制备了优质非晶氮化硅薄膜，其介电常数为７．５、击穿强度为５．５ＭＶ／ｃｍ、电导率为１０－１３（Ωｃｍ）－１。     

Two-level optimal output feedback stabilizer design

The paper addresses the design of two-level power system stabilizers using an optimal reduced order model whose state variables are torque angles and speeds. The reduced order model retains their physical meaning and is used to design a two-level linear feedback controller that takes into account the realities and constraints of electrical power systems. The two-level control strategy is used, and a global control signal is generated from the output variables to minimize the effect of interactions. The effectiveness of this controller is evaluated and a multimachine system is given as an example to illustrate the advantages of the proposed method. Responses of the system with a two-level scheme and an optimal reduced order scheme are included for comparative analysis.     

Gate and drain currents in off-state buried-type p-channel LDDMOSFETs

The buried-type p-channel LDD MOSFETs biased at high positive gate voltage exhibit novel characteristics: (1) the ratio of the drain to gate currents is about 1×10^-3 to 5×10^-3; and (2) the gate and drain currents both are functions of only the gate voltage minus the n-well bias. Such characteristics are addressed based on the formation of the surface n ⁺ inversion layer due to the punchthrough of the buried channel to the underlying shallow p-n junction. The measured gate current is due to the Fowler-Nordheim tunneling of electrons from this inversion layer surface and the holes generated within the high-field oxide constitute the drain current. The n⁺ inversion layer surface potential is found to be equal to the n-well bias plus 0.55 V. As a result, both the oxide field and the gate and drain currents are independent of drain voltage     

Fuzzy reasoning Petri nets

This paper presents a fuzzy reasoning Petri net (FRPN) model to represent a fuzzy production rule-based system. The issues of how to represent and reason about rules containing negative literals are addressed in the proposed PN model. The execution rules based on the model are defined formally using the operators in max-algebra. Then, a fuzzy reasoning algorithm is proposed to perform fuzzy reasoning automatically. The algorithm is consistent with the matrix equation expression method in the traditional PNs and allows one to exploit the maximum parallel reasoning potential embedded in the model. The legitimacy and feasibility of the proposed approach are proved and validated through a turbine fault diagnosis expert system.     

Generating weighted fuzzy rules from relational database systems for estimating values using genetic algorithms

In recent years, some methods have been proposed to estimate values in relational database systems. However, the estimated accuracy of the existing methods are not good enough. In this paper, we present a new method to generate weighted fuzzy rules from relational database systems for estimating values using genetic algorithms (GAs), where the attributes appearing in the antecedent part of generated fuzzy rules have different weights. After a predefined number of evolutions of the GA, the best chromosome contains the optimal weights of the attributes, and they can be translated into a set of rules to be used for estimating values. The proposed method can get a higher average estimated accuracy rate than the methods we presented in two previous papers.     

地图中铁路、道路提取和恢复显示的方法

本文提出一种从军用地图中提取铁路、道路的半自动方法和自动恢复显示其在地图中标识方式的算法,从而进一步实现地图图形显示系统的多层次结构。     

Formant labelling using pole-focused spectra

An algorithm is introduced which labels formants from the peaks of pole-focused spectra. A clustering procedure is first used to produce line segments of possible formants. These can be considered as anchor traces for the later processing. Rule-based labelling is then applied to provide final formant trace estimates. Experimental results show that the proposed algorithm offers improved formant labelling accuracy.     

Shrinkage and splitting of microcracks under pressure simulated by the finite-element method

The two-dimensional finite-element method is applied to analyze the shrinkage and splitting of microcracks regularly arranged on or perpendicular to a grain boundary under pressure. Grain-boundary and surface diffusions are coupled by the boundary conditions at the triple point of the microcrack surface and the grain boundary. The shrinkage and splitting processes for the two kinds of microcracks are revealed by detailed finite-element analyses. For the microcrack lying on a grain boundary, it first shrinks to a small void shape, then the void is split by the grain boundary and the two split voids assume a cylindrical shape under the capillary force of the surface. For the microcrack perpendicular to the grain boundary, it is split into two segments by the grain boundary during the early stage of shrinkage. Then, the split microcracks stop shrinking and evolve into two cylindrical channels with a circular section by the capillary force of the surface. These evolution processes are controlled by the applied pressure, microcrack spacing, ratio of grain-boundary diffusion to surface diffusion, and equilibrium dihedral angle, defined by surface and grain-boundary tensions. The influences of these controlled parameters on the evolution processes are numerically clarified based on a great number of finite-element analyses.