Feasibility of Sludge Ozonation for Stabilization and Conditioning

A pilot-scale sludge treatment plant was built to investigate the feasibility of ozonation processes for waste activated sludge treatment. Ozonation of wastewater sludge resulted in mass reduction by mineralization as well as by supernatant and filtrate recycle. Another advantage of sludge ozonation is a significant improvement of settleability and dewaterability. Experimental results showed that mass reduction of 70% and volume reduction of 85% compared with the control sludge was achieved through the sludge ozonation at a dose of 0.5?gO₃/gDS. It is also interesting to note that the filterability deteriorates up to ozone dose of 0.2?gO₃/gDS and then improves considerably at a higher ozone dose. The filterability could be improved by chemical conditioning even at a low ozone dose. The economic feasibility by cost analysis reveals that ozonation processes can be more economical than other alternative processes for sludge treatment and disposal at small-sized wastewater treatment plants.     

Manufacturing and foaming of high melt viscosity of polypropylene by using electron beam radiation technology

The high melt viscosity of polypropylene was studied by grafting bifunctional monomers, 1,6‐hexanediol diacrylate (HDDA) and tripropylene glycol diacrylate (TPGDA), onto homopolypropylene (HPP) and random ter‐polypropylene (RTPP) under electron‐beam irradiation. Creation of the high‐melt‐viscosity polypropylene was possible at low radiation dosage and low monomer content, under a prohibition of both radiation degradation and homopolymerization. TPGDA monomer was more effective in increasing the melt viscosity of HPP compared with RTPP, whereas HDDA monomer was more effective for enhancing the melt viscosity of RTPP. Such different effects of monomers on melt viscosity may arise from different monomer structures, namely, TPGDA has additional three methyl groups, but HDDA has no methyl groups. Electron‐beam radiation technology, on an increase of the melt viscosity, was much more effective in HPP than RTPP, when compared with virgin polymers. Modified RTPP and HPP with high melt viscosity were capable of foaming with numerous fine cells, of which the modified HPP with 1.5 mmol TPGDA and 0.5 kGy could create more spherical foam cells and its bending strength was 1.5 times more than that of the foamed RTPP. POLYM. ENG. SCI., 46:431–437, 2006. © 2006 Society of Plastics Engineers.     

Enhanced surface morphologies of screen-printed carbon nanotube films by heat treatment and their field-emission properties

A heating process for obtaining free-standing carbon nanotube emitters is presented with the aim of improving field-emission properties from the screen-printed multiwalled carbon nanotube (MWCNT) films. Using an atmosphere with an optimum combination of nitrogen and air for heat treatment of CNT films, the CNT emitters can be made to protrude from the surface. This allows for a high emission current and the formation of very uniform emission sites without special surface treatment. The morphological change of the CNT film by this technique has eliminated additional processing steps, such as surface treatment which may result in secondary contamination and damage to the film. Despite its simplicity the process provides a high reproducibility in emission current density which makes the films suitable for practical applications.     

Microwave Dielectric Properties and Low-Temperature Cofiring of BaTe4O9 with Aluminum Metal Electrode

Polycrystalline BaTe₄O₉ ceramic compound was investigated as a promising microwave dielectric compound for low-temperature cofired ceramics (LTCC) applications. The binary phase BaTe₄O₉ was synthesized and subsequently densified over the temperature range of only 500°–550°C, which allows for low-temperature cofiring with aluminum metal. The dielectric properties of BaTe₄O₉ ceramics sintered at 550°C for 2 h were determined in the microwave region of 12–14 GHz. The dielectric constant and Q × f product obtained were 17.5 and 54 700 GHz at 12 GHz, respectively. The temperature coefficient of resonance frequency showed a negative value of −90 ppm/°C. In terms of its evaluation for LTCC, the BaTe₄O₉ composition was found to be chemically compatible and successfully cofired with highly conductive aluminum electrode, while maintaining good electrical performance.     

A visual study on flame behavior in tone-excited non-premixed jet flames

A visualization study on the effect of forcing amplitude in tone-excited jet diffusion flames has been conducted. Visualization techniques are employed using optical schemes, which are a light scattering photography. Flame stability curve is attained according to Reynolds number and forcing amplitude at a fuel tube resonant frequency. Flame behavior is globally grouped into two from attached flame to blown-out flame according to forcing amplitude; one sticks the tradition flame behavior which has been observed in general jet diffusion flames and the other shows a variety of flame modes such as the flame of a feeble forcing amplitude where traditionally well-organized vortex motion evolves, a fat flame, an elongated flame, and an in-burning flame. Particular attention is focused on an elongation flame, which is associated with a turnabout phenomenon of vortex motion, and on a reversal of the direction of vortex roll-up. It is found that the flame length with forcing amplitude is the direct outcome of the evolution process of the formed inner flow structure. Especially the negative part of the acoustic cycle under the influence of a strong positive pressure gradient causes the shapes of the fuel stem and fuel branch part and even the direction of vortex roll-up to dramatically change.     

Living cationic polymerization of isobutyl vinyl ether (II): Photoinduced living cationic polymerization in a mixed solvent of toluene and diethyl ether

A new method of preparation of living cationic polymer of isobutyl vinyl ether via photoinduced polymerization in the presence of diphenyliodonium iodide (DPII, initiator) and zinc iodide in a mixed solvent of toluene/diethyl ether, which was irradiated at ?78°C for short period, was completed within 15 min. The reaction was allowed for further reaction in the dark until monomer was fully consumed. It was found that increase in the conversion of monomer to polymer during the irradiation is very limited. Confirmation of the linear dependence of number‐average molar mass of resulting polymer on % conversion together with the fact that polymerization proceeds until monomer consumption, and controllability of number‐average molar mass of resulting polymer, depending on the molar ratio of monomer and initiator, strongly suggests the living nature of this polymerization, unless reaction temperature becomes higher than 0°C, i.e., the absence of chain breaking process. The narrow molar mass distribution, whose polydispersity index values are less than 1.2, reveals that the rate of initiation where irradiation is usually completed within 15 min is much faster than that of propagation in cationic nature in this system. Effect of some major factors, such as solvent polarity and temperature, on the living nature of the polymerization was also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3581–3586, 2006     

Editing and Synthesizing Two‐Character Motions using a Coupled Inverted Pendulum Model

This study aims to develop a controller for use in the online simulation of two interacting characters. This controller is capable of generalizing two sets of interaction motions of the two characters based on the relationships between the characters. The controller can exhibit similar motions to a captured human motion while reacting in a natural way to the opponent character in real time. To achieve this, we propose a new type of physical model called a coupled inverted pendulum on carts that comprises two inverted pendulum on a cart models, one for each individual, which are coupled by a relationship model. The proposed framework is divided into two steps: motion analysis and motion synthesis. Motion analysis is an offline preprocessing step, which optimizes the control parameters to move the proposed model along a motion capture trajectory of two interacting humans. The optimization procedure generates a coupled pendulum trajectory which represents the relationship between two characters for each frame, and is used as a reference in the synthesis step. In the motion synthesis step, a new coupled pendulum trajectory is planned reflecting the effects of the physical interaction, and the captured reference motions are edited based on the planned trajectory produced by the coupled pendulum trajectory generator. To validate the proposed framework, we used a motion capture data set showing two people performing kickboxing. The proposed controller is able to generalize the behaviors of two humans to different situations such as different speeds and turning speeds in a realistic way in real time.     

Wetting properties of polystyrene ionomers treated with plasma source ion implantation

The wetting properties of polystyrene‐based ionomers treated with plasma source ion implantation (PSII) were investigated by the measurement of water contact angles. When sulfonated ionomers were aged for a few days, the hydrophobic recovery for the ionomers became much slower than that for the nonionic polymers. However, when the samples were aged over 20 days, the water contact angle of the ionomers converged with that of the nonionic polymer. Thus, it was concluded that the ionic interaction between the ionic groups and the presence of ionic groups together resulted in the slow hydrophobic recovery and that the aging effect was significant for the ionomers. For the methacrylate ionomer of low ion content, on the other hand, it was found that the PSII treatment produced only a small change in hydrophobic recovery behavior. Thus, it was suggested that the low ionic content coupled with the small size of the ionic unit might cause changes only of a very insignificant degree in hydrophobic recovery behavior. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2500–2504, 2002     

Microstructural Evidence for Diffusion-Driven Tetragonal-to-Orthorhombic Phase Transformation in Y-Ba-Cu-O Superconductor

Microstructures of Y-Ba-Cu-O superconductor were observed using a polarized microscope. Orthorhombic and tetragonal phases were easily distinguished by the optical etching with cross-polarized light. In the specimen cooled rapidly in oxygen, it was possible to see the path of oxygen diffusion by observing the variation of the twin concentration. At the boundary between transformed and untransformed materials, evidence for diffusion-driven transformation could be clearly seen.     

Permeability characteristics of carbonated concrete considering capillary pore structure

During carbonation process, the calcium phases present in cement are attacked by CO₂ and converted into CaCO₃ and the permeability of concrete is changing due to the change in porosity. The rate of carbonation depends upon porosity and moisture content of the concrete. Especially in underground reinforced concrete structures, the interior portion of concrete surface may be exposed to carbonation and the exterior portion of concrete surface exposed to wet soil or underground water. As carbonation proceeds from outer surface into internal portion of concrete, microstructure is also changed continuously from outer surface into internal portion of concrete. Even the deteriorations in the structures due to the carbonation have been reported more, research on permeability characteristics of concrete considering carbonation and micro-structural information is very scarce.In this study, the permeability coefficient in carbonated concrete is derived by applying a capillary pore structure formation model in carbonated cement mortar and assuming that aggregates do not affect carbonation process in early-aged concrete as a function of porosity. The permeability obtained from the micro-level modeling for carbonated concrete is verified with the results of accelerated carbonation test and water penetration test in cement mortar.