Incremental transmission loss allocation under pool dispatch

Incremental transmission loss analysis has been used for decades, but recent interest in its application to loss allocation calls for new in-depth results. This paper demonstrates that, for incremental methods to be applied correctly in loss allocation, it is first necessary to specify the load distribution and loss supply strategies. Incremental loss allocation among bus power injections is shown to be arbitrary and, therefore, open to challenge as discriminatory. Loss allocation is possible among incremental loads and/or generators, but the proportion of the total losses assigned to either one is arbitrary. Unique, nonarbitrary incremental loss allocations are however possible among the "equivalent" incremental bilateral exchanges between generators and loads. From these basic components it is possible then to calculate the allocation among generators or loads in any specified proportion. The main results, although developed initially for small increments, are extended to large variations. Finally, a general incremental loss allocation algorithm is developed and tested     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.     

Fuzzy Learning of Talbot Effect Guides Optimal Mask Design for Proximity Field Nanopatterning Lithography

Processing methods used in photonics and nanotechnology possess many limitations restricting their application areas such as high cost, inability to produce fine details, problems with scalability, and long processing time. Proximity field nanopatterning is a lithography method which surpasses these limitations. By using interference patterns produced by a two-dimensional phase mask, the technique is able to generate a submicron detailed exposure on a millimeter-size slab of light sensitive photopolymer, which is then developed like a photographic plate to reveal three-dimensional interference patterns from the phase mask. While it is possible to use simulations to obtain the interference patterns produced by a phase mask, realizing the mask dimensions necessary for producing a desired interference pattern is analytically challenging due to the intricacies of light interactions involved in producing the final interference pattern. An alternative method is to iteratively optimize the phase mask until the interference patterns obtained converge to the desired pattern. However, depending on the optimization technique used, one either risks a significant probability of failure or requires a prohibitive number of iterations. We argue that an optimization technique that is to take advantage of the physics of the problem using machine learning methods (here fuzzy learning) can lead to competent mask design. This technique is described in this letter.     

Modification of platinum surfaces by spontaneous deposition: Methanol oxidation electrocatalysis

The presence of a second metal on platinum surfaces affects the performance of methanol oxidation. However, most of the electrocatalytic reactions are studied by using electrochemically deposited platinum alloys, but in the case of spontaneous deposition the situation is not so clear since the surface distribution, stability and morphology are usually not well documented. The formation of surface decorated samples on mono- and poly-crystalline platinum is followed by electrochemical and spectroscopic techniques and analysis of their performance towards methanol adsorption and oxidation compared with that on pure platinum. Pt/Sn and Pt/Ru are of special interest because of their well-known performance in methanol fuel cells. Methanol oxidation on Pt(111)/Ru, Pt(111)/Sn and Pt(111) shows that ruthenium is the only one able to promote the reaction since the simultaneous dissolution of tin occurs and competes with the process of interest. The in situ infrared spectroscopy is used to compare methanol oxidation on Pt(111)/Ru and Pt(111) in acid media using p-polarized light. The formation of bridge bound carbon monoxide is inhibited in the presence of ruthenium ad-species, whereas on Pt(111) the three adsorption configurations are observed. Linear sweep polarization curves and Tafel slopes (calculated from steady state potentiostatic plots) for methanol oxidation are compared on polycrystalline surfaces modified by tin or ruthenium at different coverages. There is almost no change in the Tafel slopes due to the presence of the foreign metal except for Pt/Ru, where a 0.09 V decade⁻¹ slope was calculated below 0.55 V due to hydroxyl adsorbates on ruthenium islands. The anodic stripping of methanol residues on the three surfaces indicates a lower amount of carbon monoxide-type adsorbates on Pt/Ru, and the simultaneous tin dissolution process leading to residues oxidation on Pt/Sn electrodes.     

Properties of poly(ethylene terephthalate)–poly(ethylene naphthalene 2,6‐dicarboxylate) blends with montmorillonite clay

The production and properties of blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) with three modified clays are reported. Octadecylammonium chloride and maleic anhydride (MAH) are used to modify the surface of the montmorillonite–Na⁺ clay particles (clay–Na⁺) to produce clay–C18 and clay–MAH, respectively, before they are mixed with the PET/PEN system. The transesterification degree, hydrophobicity and the effect of the clays on the mechanical, rheological and thermal properties are analysed. The PET–PEN/clay–C18 system does not show any improvements in the mechanical properties, which is attributed to poor exfoliation. On the other hand, in the PET–PEN/clay–MAH blends, the modified clay restricts crystallization of the matrix, as evidenced in the low value of the crystallization enthalpy. The process‐induced PET–PEN transesterification reaction is affected by the clay particles. Clay–C18 induces the largest proportion of naphthalate–ethylene–terephthalate (NET) blocks, as opposed to clay–Na⁺ which renders the lowest proportion. The clay readily incorporates in the bulk polymer, but receding contact‐angle measurements reveal a small influence of the particles on the surface properties of the sample. The clay–Na⁺ blend shows a predominant solid‐like behaviour, as evidenced by the magnitude of the storage modulus in the low‐frequency range, which reflects a high entanglement density and a substantial degree of polymer–particle interactions. Copyright © 2005 Society of Chemical Industry     

The growth of ambient aerosols in the conditions of the respiratory system

The effect on ambient aerosols of exposure to the conditions of the respiratory system was determined by sampling simultaneously through two dichotomous samplers in parallel. In one of the samplers the aerosol was brought to 37°C and near 100% relative humidity before passing through the virtual impactor. The results show that, as a result of humidification, about 10–15% by mass of the aerosol which would normally been collected in the fine (less than 2.5 μm aerodynamic diameter) fraction of the sample grows sufficiently when humidified to be collected with the coarse fraction. It is suggested that the direct application to inhalation studies of dichotomous sampler results should be approached with some caution.