Precipitation at interphase boundaries

Three problems in precipitation at interphase boundaries are examined. 1) The classu argument as to the particular phase in which such a precipitate nucleates is shown to be irrelevant; except in a special situation, the critical nucleus must normally penetrate both phases forming the interphase boundary. 2) The relative penetrations into the two phases achieved during growth can be very different than those expected during nucleation; hence, deductions about the nucleation process based upon observations on growth morphologies can be quite misleading. 3) The observations of Honeycombe and others that the nucleation of carbides at austenite: ferrite boundaries occurs predominantly at the low energy, immobile broad faces of ledges rather than at the higher energy, mobile risers of ledges are accounted for theoretically on the basis of the high velocities of the risers preventing nucleation. Example calculations on a Ti-Ni alloy indicate that precipitation at the risers of ledges may become possible in substitutional systems, but only at lower homologous temperatures, and if the migration of these boundaries is still controlled by volume diffusion while nucleation is controlled by interfacial diffusion.     

Q fever (Coxiella burnetii) investigations in dairy cattle: challenge of immunity after vaccination

The immunity of Holstein-Friesian dairy cows vaccinated against Coxiella burnetii was challenged with 4 X 10(8) infective guinea pig doses of viable rickettsiae. Cows that were vaccinated had normal full-term calves, whereas 2 nonvaccinated cows aborted late in pregnancy. Intrauterine infection of the fetus was indicated by recovery of the organism from tissues of the fetus. Coxiella burnetii was recovered from milk, colostrum, and placenta of vaccinated and nonvaccinated cows after challenge inoculation, but the rickettsiae recovered were as many as 1,000 times more numerous in nonvacinated cows.     

Trends in deaths due to motorcycle crashes and risk factors in injury collisions

In the past 25 years, the numbers of registered motorcycles in the United States and California have increased about 1000 and 1100%, respectively. In the same period, the motorcycle collision death rate per million population more than doubled. The purposes of the study were to examine time trends in deaths due to motorcycle collisions, examine a methodologic problem in the study of motor vehicle collision death rates, and to determine driver and vehicle factors which may discriminate in the production of motorcycle crash related injurites.

With the exception of 1974, the increase in the ratio of registered motorcycles per 100,000 population in the United States corresponded to an increase in the crude death rate per million population. A similar pattern was also found in California.

Stepwise discriminant analysis was used to determine an optimum set of factors associated with motorcycle collision injuries. The analysis indicated that for male drivers age was the single factor most significantly related to motorcycle collision injuries. Other factors, in addition to age, which added to the power of the discrimination included number of prior motorcycle driving violations, frequency of motorcycle use, number of prior motorcycle crashes, motorcycle drivers' training, and height of the drivers.     

Microstructure and Properties of HVOF-Sprayed WC-(W,Cr)<Subscript>2</Subscript>C-Ni Coatings

The composition WC-(W,Cr)₂C-Ni is one of the standard compositions used for the preparation of thermally sprayed coatings by high velocity oxy-fuel (HVOF) spraying. Surprisingly, this composition has been poorly investigated in the past. Frequent use of commercial designations WC-‘CrC’-Ni, WC-Cr₃C₂-Ni, and WC-NiCr indicates the insufficient knowledge about the phase compositions of these powders and coatings. The properties of these coatings differ significantly from those of WC-Co and WC-CoCr coatings. In this paper, the results of different series of experiments conducted on HVOF-sprayed WC-(W,Cr)₂C-Ni coatings are compiled and their specific benefits pointed out. The focus of this study is on the analysis of the microstructures and phase compositions of the feedstock powders and coatings. Unlike WC-Co and Cr₃C₂-NiCr, WC-(W,Cr)₂C-Ni is not a simple binary hard phase—binder metal composite. The phase (W,Cr)₂C with unknown physical and mechanical properties appears as a second hard phase, which is inhomogeneously distributed in the feedstock powders and coatings. As examples of coating properties, the oxidation resistance and dry sliding wear properties are compared with those of WC-10%Co-4%Cr coatings.     

Solid-state grafting of maleic anhydride onto polypropylene: The influence of morphology of polypropylene on heterogeneous reaction

Polypropylene (PP) was modified with maleic anhydride (MAH) via heterogeneous solid-state radical grafting performed in a fluidized polymerization reactor. The effect of PP morphology and different concentration of initiator (dibenzoyl peroxide, DBP) on the course of the reaction and grafting efficiency was evaluated with using infrared spectroscopy, scanning electron microscopy (SEM) and particle surface analysis (BET method). With respect to obtained results, the reaction course can be strongly affected by the reaction conditions and PP morphology. Unlike the reactive modification in melt, heterogeneous reaction exhibits lower extent of β-scission albeit the reaction conversion is lower. Solid-state grafting can be used as an alternative method for the surface modification of nonpolar surfaces with polar monomers under mild conditions.     

Bisamidate Prodrugs of 2‐Substituted 9‐[2‐(Phosphonomethoxy)ethyl]adenine (PMEA,adefovir) as Selective Inhibitors of Adenylate Cyclase Toxin from Bordetella pertussis

Novel small‐molecule agents to treat Bordetella pertussis infections are highly desirable, as pertussis (whooping cough) remains a serious health threat worldwide. In this study, a series of 2‐substituted derivatives of 9‐[2‐(phosphonomethoxy)ethyl]adenine (PMEA, adefovir), in their isopropyl ester bis(L ‐phenylalanine) prodrug form, were designed and synthesized as potent inhibitors of adenylate cyclase toxin (ACT) isolated from B. pertussis. The series consists of PMEA analogues bearing either a linear or branched aliphatic chain or a heteroatom at the C2 position of the purine moiety. Compounds with a small C2 substituent showed high potency against ACT without cytotoxic effects as well as good selectivity over human adenylate cyclase isoforms AC1, AC2, and AC5. The most potent ACT inhibitor was found to be the bisamidate prodrug of the 2‐fluoro PMEA derivative (IC₅₀=0.145 μM ). Although the bisamidate prodrugs reported herein exhibit overall lower activity than the bis(pivaloyloxymethyl) prodrug (adefovir dipivoxil), their toxicity and plasma stability profiles are superior. Furthermore, the bisamidate prodrug was shown to be more stable in plasma than in macrophage homogenate, indicating that the free phosphonate can be effectively distributed to target tissues, such as the lungs. Thus, ACT inhibitors based on acyclic nucleoside phosphonates may represent a new strategy to treat whooping cough.     

Electrically conductive silicon carbide with the addition of TiNbC

The work deals with the preparation of dense SiC based ceramics with high electrical conductivity. SiC samples with different content of conductive TiNbSiCO based phase were hot pressed at 1820 °C for 1 h in Ar atmosphere under mechanical pressure of 30 MPa. The conductive phase is a mixture of 50 wt% TiNbC (molar ratio of Ti/NbC is 1:1.8) and 50 wt% eutectic composition of Y₂O₃SiO₂. Composite with 30% of conductive TiNbSiCO phase showed the highest electrical conductivity 28.4 S mm^?1, while the good mechanical properties of SiC matrix were preserved (fracture toughness K_IC = 5.4 MPa m^1/2 and Vickers hardness 17.8 GPa).The obtained results show that the developed additive system is suitable for the preparation of SiC-based composite with sufficient electrical conductivity for electric discharge machining.     

Texture Properties of Dutch-Type Cheese as a Function of Its Location and Ripening

The aim of the study was to explore texture changes of Dutch-type cheese at its different locations during 126-day ripening at the temperature common for maturation of this type of cheese (10°C). Each block of cheese was divided into 3 slices and texture properties were studied in 13 segments evenly distributed in each slice. Due to cheese brining, a significant increase of hardness and elastic component was reported especially in the edge segments. During the subsequent ripening, both hardness and elastic component of natural cheese decreased gradually in all segments and slices. Studied parameters of individual parts of cheese did not demonstrate uniform rate of changes during the ripening period. In the whole experiment (even after 126-day ripening), hardness and elastic component of the cheese in core showed lower values compared to those obtained in the edge of all slices.