A new Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor

A new and interesting Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor has been fabricated and studied. The steady-state and transient responses with different hydrogen concentrations has been measured at various temperatures. Based on the large Schottky barrier height and presence of oxide layer, the studied device exhibits a high hydrogen detection sensitivity and wide temperature operating regime. The studied device exhibits the low-leakage current and obvious current changes when exposed to hydrogen-contained gas. Even at room temperature, a very high hydrogen detection sensitivity of 155.9 is obtained when a 9090 ppm H/sub 2//air gas is introduced. Furthermore, when exposed to hydrogen-contained gas at 95/spl deg/C, both the forward and reverse currents are substantially increased with increased hydrogen concentration. In other words, the studied device can be used as a hydrogen sensor under the applied bidirectional bias. Under the applied voltage of 0.35 V and 9090 ppm H/sub 2//air hydrogen ambient, a fast adsorption response time about 10 s is found. The transient and steady-state characteristics of hydrogen adsorption are also investigated.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

Structural Changes Induced in Nonstoichiometric Titanium Carbide by High-Temperature Deformation

The microstructure evolution in nonstoichiometric titanium carbide is studied during high-temperature deformation at high strain rates and low strains (shock compression) and at slow strain rates and high strains (superplastic regime). The results demonstrate that high-temperature deformation in a broad range of strain rates offers a means of controlling the microstructure of titanium carbide. By varying deformation conditions, one can obtain materials differing in microstructure and chemical composition, in particular, with equilibrium and nonequilibrium microstructures. Accordingly, the physicochemical properties of such materials also differ.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.     

Management gaps analysis: a case study of groundwater resource management in New Zealand

The primary objective of this project is to identify gaps, whether real or perceived, that hinder effective groundwater management in New Zealand. These gaps show as gaps in information, gaps in implementation, gaps in technological and management tools, and gaps in understanding of fundamental processes. The secondary objective is to propose a management strategy to close the identified gaps. Several methods are used to meet these objectives: surveys distributed to selected staff in each regional council; the review of various written reports; the analysis of land-use databases; and private consultation within each regional council. Results show that groundwater management in New Zealand is generally reactionary with the main gaps being in strategic planning and national guidelines. Most gaps appear to be predominantly information and implementation issues. In some cases there are gaps in the understanding of fundamental processes within an aquifer system, including the long-term effects of land-use on groundwater quality. An adaptive management approach is suggested as a means of closing these gaps.     

毛细管气相色谱法测定丙烯腈中丙烯醛、丙酮、乙腈的含量

丙烯腈中有机杂质丙烯醛、丙酮、乙腈是其重要指标，现在丙烯腈的国标测试方法用填充柱气相色谱法分析丙烯腈中有机杂质丙烯醛、丙酮、乙腈的含量，此法分析时间长，灵敏度低。为了及时准确提供分析数据，用毛细管气相色谱法测定丙烯腈中有机杂质的含量。     

Bio-layer management in anaerobic membrane bioreactors for wastewater treatment.

Membrane separation technology represents an alternative way to achieve biomass retention in anaerobic bioreactors for wastewater treatment. Due to high biomass concentrations of anaerobic reactors, cake formation is likely to represent a major cause of flux decline. In the presented research, experiments are performed on the effect of biomass concentration and level of gas sparging on the hydraulic capacity of a submerged anaerobic membrane bioreactor. Both parameters significantly affected the hydraulic capacity, with biomass exerting the most pronounced effect. After 50 days of continuous operation the critical flux remained virtually unchanged, despite an increase in membrane resistance, suggesting that biomass characteristics and hydraulic conditions determine the bio-layer formation rather than the membrane's fouling level. The concept of bio-layer management is introduced to describe the programmed combination of actions performed in order to control the formation of biomass layer over membranes.