Hot-carrier aging of the MOS transistor in the presence of spin-onglass as the interlevel dielectric

The effect of introducing a polysilicate or polysiloxane spin-on glass (SOG) as a component of the interlevel dielectric in a multilevel integrated circuit on the hot-carrier aging of the MOS transistor is discussed. It was found that the presence of SOG led to accelerated aging of the MOS transistor: factors of 20 and 5 for silicate and siloxane, respectively. This effect is attributed to water absorbed in the SOG films. a correlation was found for the hot-carrier aging rate and the amount of absorbed water     

THE OPTIMUM SPEED OF VISUAL INSPECTION USING A RANDOM SEARCH STRATEGY

Choosing a standard speed for visual inspection is difficult using standard work measurement techniques. This paper uses a different approach, taking a model of human functioning in inspection and deriving an optimum speed of working so as to balance the cost of time against the cost of errors. Random search is used as the model and both self-paced and externally-paced conditions are derived for multiple fault types. Optimization using a Golden Section search is used to provide optimum inspection speed.     

Dissociation of gaseous hydrates in beds

A mathematical model which accounts for the mobility of the liquid phase is constructed to describe the dissociation of gaseous hydrates in beds.Translated from Inzhenerno-fizicheskii Zhurnal, Vol. 60, No. 5, pp. 736–742, May, 1991.     

Increase in urinary calcium and oxalate after fructose infusion

We have previously shown that an oral glucose load increased both calciuria and oxaluria while the ingestion of fructose induced a rise in calciuria and a decrease in oxaluria. This latter effect remains unclear and might be linked to the reduced intestinal oxalate absorption subsequent to digestive intolerance in some subjects. Such a hypothesis could be enlightened by the study of a parenteral fructose load. Therefore in 7 healthy subjects, we compared the effects of fructose infusion (F) (15 min iv infusion at 0.185 mmol/kg BW/min) to a control glucose infusion (G) on urinary calcium and oxalate. In this study, glycemia and insulinemia increased less after (F) than after (G) (respectively + 21% vs + 216%, p < 0.001 and + 230% vs + 402%, p < 0.05) and phosphatemia decreased less after (F) than after (G) (-7% vs -14%, p < 0.05). Urinary calcium and oxalate increased only after (F) (respectively + 64%, p < 0.01 and + 60%, p < 0.05). Urinary uric acid, another urolithiasis factor, increased after both (F) and (G) (respectively + 45%; p < 0.01 and + 42%; p < 0.01) but uricemia increased only after (F) (+ 25%; p < 0.01). Our results suggest an additional reason to avoid the use of fructose in parenteral nutrition, particularly in individuals with a known history of either calcium oxalate or urate urolithiasis.     

Chelated alkoxyalumoxanes and a silica-free binder based on them

Chelated alkoxyalumoxane oligomers have been synthesized through consecutive hydrolysis and alcoholysis of organoaluminum compounds stabilized by compounds capable of keto-enol tautomerism. The chelated alkoxyalumoxanes were used to prepare a silica-free binder for the fabrication of heat-resistant (up to 2050°C), chemically inert corundum ceramic composites. The likely structures of the synthesized preceramic alumoxane oligomers were inferred from physicochemical characterization results (¹H, ¹³C, and ²⁷Al NMR, IR spectroscopy, mass spectrometry, gel-permeation chromatography, thermal analysis, and elemental analysis).     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.