Optimized Characterization of Thermoelectric Generators for Automotive Application

New developments in the field of thermoelectric materials bring the prospect of consumer devices for recovery of some of the waste heat from internal combustion engines closer to reality. Efficiency improvements are expected due to the development of high-temperature thermoelectric generators (TEG). In contrast to already established radioisotope thermoelectric generators, the temperature difference in automotive systems is not constant, and this imposes a set of specific requirements on the TEG system components. In particular, the behavior of the TEGs and interface materials used to link the heat flow from the heat source through the TEG to the heat sink must be examined. Due to the usage patterns of automobiles, the TEG will be subject to cyclic thermal loads, which leads to module degradation. Additionally, the automotive TEG will be exposed to an inhomogeneous temperature distribution, leading to inhomogeneous mechanical loads and reduced system efficiency. Therefore, a characterization rig is required to allow determination of the electrical, thermal, and mechanical properties of such high-temperature TEG systems. This paper describes a measurement setup using controlled adjustment of cold-side and warm-side temperatures as well as controlled feed-in of electrical power for evaluation of TEGs for application in vehicles with combustion engines. The temperature profile in the setup can be varied to simulate any vehicle usage pattern, such as the European standard driving cycle, allowing the power yield of the TEGs to be evaluated for the chosen cycle. The spatially resolved temperature distribution of a TEG system can be examined by thermal imaging. Hotspots or cracks on thermocouples of the TEGs and the thermal resistance of thermal interface materials can also be examined using this technology. The construction of the setup is briefly explained, followed by detailed discussion of the experimental results.     

Impact of Processing on Structural and Compositional Evolution in Mixed Metal Halide Perovskites during Film Formation

Understanding crystallization processes and their pathways in metal‐halide perovskites is of crucial importance as this strongly affects the film microstructure, its stability, and device performance. While many approaches are developed to control perovskite formation, the mechanisms of film formation are still poorly known. Using time‐resolved in situ grazing incidence wide‐angle X‐ray scattering, the film formation of perovskites is investigated with average stoichiometry Cs_0.15FA_0.85PbI₃, where FA is formamidinium, using the popular antisolvent dropping and gas jet treatments and this is contrasted with untreated films. i) The crystallization pathways during spin coating, ii) the subsequent postdeposition thermal annealing, and iii) crystallization during blade coating are studied. The findings reveal that the formation of a nonperovskite FAPbI₃ phase during spin coating is initially dominant regardless of the processing and that the processing treatment (e.g., antisolvent dropping, gas jet) has a significant impact on the as‐cast film structure and affects the phase evolution during subsequent thermal treatment. It is shown that blade coating can be used to overcome the nonperovskite phase formation via solvothermal direct crystallization of perovskite phase. This work shows how real‐time investigation of perovskite formation can help to establish processing–microstructure–functionality relationships.     

A preamble-based approach for providing quality of service support in wireless sensor networks

Medium Access Control (MAC) protocols for Wireless Sensor Networks (WSN) are usually designed as random access protocols that apply different kinds of backoff strategies since Time Division Multiple Access (TDMA) based protocols with admission control are very complex and require additional mechanisms for synchronization. Without such mechanisms, fair or priority based medium access with Quality of Service (QoS) guarantees can hardly be achieved by existing protocols. Therefore, we developed a random access protocol which uses a new preamble-based medium access strategy that enables collision-free priority based access without the need of synchronization. In this paper we introduce different QoS strategies and their use cases. All strategies can be easily integrated in our protocol to meet the requirements of different target applications. Furthermore, we compare the performance of the strategies with a typical carrier-sense based protocol.     

Dependence of Photocurrent Enhancements in Quantum Dot (QD)‐Sensitized MoS2 Devices on MoS2 Film Properties

This report demonstrates highly efficient nonradiative energy transfer (NRET) from alloyed CdSeS/ZnS semiconductor nanocrystal quantum dots (QDs) to MoS₂ films of varying layer thicknesses, including pristine monolayers, mixed monolayer/bilayer, polycrystalline bilayers, and bulk‐like thicknesses, with NRET efficiencies of over 90%. Large‐area MoS₂ films are grown on Si/SiO₂ substrates by chemical vapor deposition. Despite the ultrahigh NRET efficiencies there is no distinct increase in the MoS₂ photoluminescence intensity. However, by studying the optoelectronic properties of the MoS₂ devices before and after adding the QD sensitizing layer photocurrent enhancements as large as ≈14‐fold for pristine monolayer devices are observed, with enhancements on the order of ≈2‐fold for MoS₂ devices of mixed monolayer and bilayer thicknesses. For the polycrystalline bilayer and bulk‐like MoS₂ devices there is almost no increase in the photocurrent after adding the QDs. Industrially scalable techniques are specifically utilized to fabricate the samples studied in this report, demonstrating the viability of this hybrid structure for commercial photodetector or light harvesting applications.     

An Improved On-Wafer Measurement Method for PHEMT Modeling for Millimeter Wave Application

An improved on-wafer measurement method by using coaxial calibration instead of on-wafer calibration for PHEMT modeling is proposed in this paper. The advantage is that S-parameters of PHEMT device can be measured on wafer without impedance standard substrate (ISS) after the S-parameters of the microprobes have been determined. Excellent agreement is obtained between on-wafer calibration measurement and coaxial calibration measurements, respectively.     

Tunable 3D Nanoresonators for Gas‐Sensing Applications

The detection of gas species with high sensitivity is a significant task for fundamental sciences as well as for industrial applications. Similarly, the ongoing trend for device miniaturization brings new challenges for advanced fabrication including on‐demand functionality tuning. Following this motivation, here the additive, direct‐write fabrication of freestanding 3D nanoarchitectures is introduced, which can be brought into mechanical resonance via electric AC fields. Specifically, this study focuses on the 3D nanostructure synthesis, the subsequent determination of Young's modulus, and demonstrates a postgrowth procedure, which can precisely tune the material modulus. As‐fabricated resonators reveal a Young's modulus of 9–13 GPa, which can be increased by a factor greater than 5. Next, the electric readout of the resonance behavior is demonstrated via electric current measurement as an essential element for the resonance sensor applications. Finally, the implications of gas‐physisorption and gas‐chemisorption on the resonance frequencies are studied, representing a proof‐of‐principle for sensing applications by the here presented approach.     

In Situ Scanning Electron Microscopy Observation of Growth Kinetics and Catalyst Splitting in Vapor–Liquid–Solid Growth of Nanowires

In situ observations during vapor–liquid–solid (VLS) growth of semiconductor nanowires in the chamber of an environmental scanning electron microscope (ESEM) are reported. For nanowire growth, a powder mixture of CdS and ZnS is used as a source material and silver nanoparticles as a metal catalyst. Through tracing growth kinetics of nanowires, it is found that nanowires with a relatively bigger catalyst droplet on the tip grow faster. Intriguingly, it is also found that the growth of nanowires can involve catalyst splitting: while the majority of catalyst remains at the nanowire tip and continues facilitating the growth, a portion of it is removed from the tip due to the splitting. It remains attached to the nanowire at the position where the splitting occurred and subsequently induces the growth of a nanowire branch. As far as it is known, this is the first time that catalyst splitting is revealed experimentally in situ. It is proposed that the instability of catalyst droplet caused by the volume increase is the main reason for the splitting. It is believed that in situ growth inside the ESEM can largely enrich our understanding on the metal‐catalyzed VLS growth kinetics, which may open up more opportunities for morphology‐controlled synthesis of 1D semiconductor nanowires in future study.     

Optical reconstruction of high-speed surface dynamics in an uncontrollable environment

The ability to communicate with our voice can be regarded as the concatenation of the two processes "phonation" and "modulation." These take place in the larynx and palatal and oral region, respectively. During phonation the audible primary voice signal is created by mutual reaction of vocal folds with the exhaled air stream of the lungs. The underlying interactions of masses, fluids and acoustics have yet to be identified and understood. One part of the primary signal's acoustical source are vortex induced vibrations, as e.g., created by the Coand?effect in the air stream. The development of these vorteces is determined by the shape and 3-D movements of the vocal folds in the larynx. Current clinical in vivo research methods for vocal folds do not deliver data of satisfactory quality for fundamental research, e.g., an endoscope is limited to 2-D image information. Based hereupon, a few improved methods have been presented, however delivering only selective 3-D information, either for a single point or a line. This stands in contrast to the 3-D motions of the entire vocal fold surface. More complex imaging methods, such as MRI, do not deliver information in real-time. Thus, it is necessary to develop an easily applicable, more improved examination method, which allows for 3-D data of the vocal folds surfaces to be obtained. We present a method to calibrate a 3-D reconstruction setup including a laser projection system and a high-speed camera. The setup is designed with miniaturization and an in vivo application in mind. The laser projection system generates a divergent grid of 196 laser dots by diffraction gratings. It is calibrated with a planar calibration target through planar homography. In general, the setup allows to reconstruct the topology of a surface at high frame rates (up to 4000 frames per second) and in uncontrollable environments, as e.g., given by the lighting situation (little to no ambient light) and varying texture (e.g., varying grade of reflection) in the human larynx. In particular, this system measures the 3-D vocal fold surface dynamics during phonation. Applied to synthetic data, the calibration is shown to be robust (error approximately 0.5 μm) regarding noise and systematic errors. Experimental data gained with a linear z -stage proved that the system reconstructs the 3-D coordinates of points with an error at approximately 15 μm. The method was applied exemplarily to reconstruct porcine and artificial vocal folds' surfaces during phonation. Local differences such as asymmetry between left and right fold dynamics, as well as global parameters, such as opening and closing speed and maximum displacements, were identified and quantified.     

Engineering a heavy atom derivative for the X-ray structure analysis of cyclodextrin glycosyltransferase

Based on a preliminary structural model of cyclodextrin glycosyltransferasefrom Bacillus circulans (EC 2.4.1.19 [EC] ), Ser428 and Ser475 ofthe enzyme were mutated to cysteines in order to produce suitableheavy atom derivatives. Mutant Ser475 - Cys could not be expressedas protein. Mutant Ser428 - Cys was expressed in Escherichiacoli and purified. It crystallized isomorphously and gave riseto a mercury derivative that improved the electron density map.The structural results show that the new mercury-binding siteis in a pocket at the protein surface.