CMOS artificial subretinal chip for natural light illumination

A novel CMOS oscillating pixel array for subretinal prosthesis used in natural light illumination is presented. Its prototype chips are fabricated in a standard 0.6 /spl mu/m CMOS technology. Experimental results show the device can deliver effective self-oscillation for subretinal electrical stimulation.     

高度有序多孔氧化铝模板的制备工艺与生长机制的研究

采用二次氧化法制备出高度有序的多孔氧化铝模板，结合扫描电镜和原子力显微镜对其结构、形貌进行观察和表征。研究了铝箔预处理和温度等对多孔氧化铝模板孔洞有序性的影响，讨论了有序孔洞的自组织生长机理。     

Modeling transient slag-layer phenomena in the shell/mold gap in continuous casting of steel

Mold-slag friction and fracture may cause heat-transfer variations in continuous casting, which leads to steel shell temperature and stress variations, resulting in surface cracks. Analytical transient models of liquid slag flow and solid slag stress have been coupled with a finite-difference model of heat transfer in the mold, gap, and steel shell to predict transient shear stress, friction, slip, and fracture of the slag layers. The models are validated by comparing with numerical models and plant measurements of mold friction. Using reported slag-fracture strength and time-temperature-transformation (TTT) diagrams, the models are applied to study the effect of casting speed and mold-powder viscosity properties on slag-layer behavior between the oscillating mold wall and the solidifying steel shell. The study finds that liquid-slag lubrication would produce negligible stresses. A lower mold-slag consumption rate leads to high solid friction and results in solid-slag-layer fracture and movement below a critical value. Crystalline slag tends to fracture near the meniscus and glassy slag tends to fracture near the mold exit. A medium casting speed may be the safest to avoid slag fracture, due to its having the lowest critical lubrication consumption rate. The high measured friction force in operating casters could be due to three sources: an intermittent moving solid slag layer, excessive mold taper, or mold misalignment. Other symbols are defined in Table I     

自适应比例因子模糊控制器在异步电动机调速系统中的应用

为了降低转子电阻变化对异步电动机矢量控制系统性能的影响，本文把自适应比例因子模糊控制器应用到了矢量控制系统中。介绍了自适应比例因子模糊控制方法的綦本原理，给出了使用自适应比例因子模糊控制器的异步电动机矢量控制系统的结构框图，对主模糊控制器和辅助模糊控制器进行了设计。仿真实验结果表明，采用这种控制方法的调速系统不仅具有优良的动态性能，而且对转子电阻变化具有很强的鲁棒性。     

2#板坯连铸机振动台故障分析及改造

论述了银山型钢有限公司炼钢厂2#板坯连铸机自投产以来其振动台存在的问题，根据实际情况分析论证并进行改造实施，实施后效果明显。     

En/Decoder for Spectral Phase-Coded OCDMA System Based on Amplitude Sampled FBG

A novel en/decoder for spectral phase-coded optical code-division multiple-access system based on amplitude sampled fiber Bragg grating (FBG) is proposed. Both equivalent chirp and equivalent phase shift are achieved by amplitude sampling. Compared with previous en/decoder based on step chirped FBG, it is easier to fabricate. The performance of the proposed en/decoder is verified by both numerical simulation and experimental demonstration.     

Geotechnical properties of the soft soil in Guangzhou College City

The paper describes some geotechnical properties of the soft soils in Guangzhou College City, China, which are difficult to both sample and test. Laboratory and in situ tests were carried out to assess the physical and mechanical indices of the soils. The data were statistically analyzed and linear regression undertaken such that equations could be developed by which the geotechnical properties of the soft soils can be predicted. The statistical validity of the degree of correlation confirmed that using these equations, the mechanical indices can be estimated from physical indices determined by routine testing.      

Novel blood-compatible waterborne polyurethane using chitosan as an extender

A series of novel block polymers of polyurethane (PU) and chitosan have been prepared in two steps. The first step is the preparation of PU prepolymer, obtained from polytetramethylene oxide glycol (PTMO, M_n = 1000), isophrone diisocyanate (IPDI), and 2,2′-dimethylol propionic acid (DMPA), followed by ionizing PU prepolymer with triethylamine (TEA). The second step involves PU chain-extended by water-soluble chitosan of low molecular weight (M_n = 5000) by self-emulsion polymerization method. The sizes of the latex particles, morphology, and copolymer architecture have been characterized by dynamic light scattering (DLS), general tensile test, infrared spectroscopy (IR), surface contact angle measurement, and transmission electron microscopy (TEM). Furthermore, it shows that the addition of chitosan remarkably increases anticoagulative property of PU elastomers confirmed by the recalcification time. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

回转窑供电装置改造

本阐述了回转窑供电装置存在的缺陷，亦即改造过程和改造后的效果。     

Preparation and Characterization of Carboxymethyl Chitosan and β-Cyclodextrin Microspheres by Spray Drying

Three kinds of carboxymethyl chitosan/β-cyclodextrin microspheres loaded with theophylline were prepared by spray drying intended for pulmonary delivery. Mucociliotoxicity, permeation rate, and drug release characteristics of the product were investigated. The microspheres obtained by spray drying were found to be spherical with smooth or wrinkled surfaces. The mean particle size was between 3.39 and 6.06 µm. The microspheres demonstrated high product yield (43.7-50.2%), high drug loading (13.7-38.1%), and high encapsulation efficiency (86.9-92.8%). FT-IR indicated that there were interactions of theophylline with carboxymethyl chitosan matrix. Further studies on mucociliotoxicity and permeation confirmed that microspheres had better adaptability and high permeation rate. In vitro drug release from the microspheres was not related to the drug/polymer ratios.