Synthesis and release of ATP by soluble mitochondrial F1 in complex with its inhibitor protein during dimethylsulfoxide-water transitions

Soluble mitochondrial F1 and F1 in complex with the natural ATPase inhibitor protein (F1-IP) catalyze the spontaneous synthesis of [gamma-32P]ATP from medium [32P]phosphate and enzyme-bound ADP when incubated in media with dimethylsulfoxide (Me2SO); under these conditions, the synthesized [gamma-32P]ATP is not released into the media, it remains tightly bound to the enzymes [Gómez-Puyou, A., Tuena de Gómez-Puyou, M. & de Meis, L. (1986) Eur. J. Biochem. 159, 133-140]. Some of the characteristics of the synthesized [gamma-32P]ATP were studied in F1 and F1-IP (ATPase activities of 70 and 1-3 micromol x min(-1) x mg(-1), respectively). In Me2SO media, gamma-phosphate of synthesized ATP in F1 or F1-IP exchanges with medium phosphate. From the rates of the exchange reaction, the half-times for hydrolysis of the synthesized ATP in F1 and F1-IP were calculated: 45 min and 58 min for F1 and F1-IP, respectively. The course that synthesized [gamma-32P]ATP follows after dilution of the Me2SO synthetic mixture with aqueous buffer was determined. After dilution, the half-life of synthesized ATP in F1 was less than 1 min. In F1-IP, ATP was also hydrolyzed, but at significantly lower rates. In F1-IP, dilution also produced release of the synthesized [gamma-32P]ATP. This was assayed by the accessibility of [gamma-32P]ATP to hexokinase. About 25% of [gamma-32P]ATP synthesized in F1-IP, but not in F1, was released into the media after dilution with aqueous buffer that contained 20 mM phosphate. Release of tightly bound ATP required the binding energy of phosphate and solvation of F1-IP, however, the particular kinetics of F1-IP were also central for medium ATP synthesis in the absence of electrochemical H+ gradients.     

Response spectrum analysis of piping systems with elastic-plastic gap supports

A new seismic support device and its application in piping systems is described. The device, E-BAR (patented), can be cost effectively used for snubber replacement programs, mitigation of hydraulic transients, pipe whip and as a thermal stop. The device has pre-set gaps to allow free thermal movement. During a seismic or other dynamic load event, if the pipe movement exceeds the gap dimension, the device acts as an elastic or elastic-plastic restraint. The device also has a unique design feature for not exceeding the restraint force beyond a specified limit design value. To analyze piping systems with gap supports having elastic-plastic characteristics, modal analysis procedures for both response spectrum and time history methods are developed. The comparison of responses obtained from the procedures with nonlinear time history analysis and test results available in the literature shows excellent correlation. A pilot program conducted for snubber replacement with E-BARs demonstrates that the limit force feature of E-BAR makes them very attractive for snubber replacement. This is because a particular E-BAR with a specified limit design force can be selected, such that, the E-BAR replacing the snubber does not require any modifications be made to the existing support steel and hardware.     

Threshold voltage-minimum gate length trade-off in buried channelPMOS devices for scaled supply voltage CMOS technologies

The trade-off between threshold voltage (V_th) and the minimum gate length (L_min) is discussed for optimizing the performance of buried channel PMOS transistors for low voltage/low power high-speed digital CMOS circuits. In a low supply voltage CMOS technology it is desirable to scale V_th and L_min for improved circuit performance. However, these two parameters cannot be scaled independently due to the channel punch-through effect. Statistical process/device modeling, split lot experiments, circuit simulations, and measurements are performed to optimize the PMOS transistor current drive and CMOS circuit speed. We show that trading PMOS transistor V_th for a smaller L_min results in faster circuits for low supply voltage (3.3 to 1.8 V) n⁺-polysilicon gate CMOS technology, Circuit simulation and measurements are performed in this study. Approximate empirical expressions are given for the optimum buried channel PMOS transistor V _th for minimizing CMOS circuit speed for cases involving: (1) constant capacitive load and (2) load capacitance proportional to MOS gate capacitance. The results of the numerical exercise are applied to the centering of device parameters of a 0.5 μm 3.3 V CMOS technology that (a) matches the speed of our 0.5 μm 5 V CMOS technology, and (b) achieves good performance down to 1.8 V power supply. For this process the optimum PMOS transistor V_th (absolute value) is approximately 0.85-0.90 V     

Restoration of masonry facades, renders and final coats in a severe climate

The restoration of relatively old masonry buildings, 1870-1920, represents about 119930 flats and offices in the 4-5 largest cities in Norway. Driving rain and a severe climate are the key factors for deterioration. The paper describes a case study at the city campus of the University of Oslo.     

Development of a distributed sensing technique using Brillouinscattering

This paper reviews the developments of a distributed strain and temperature sensing technique that uses Brillouin scattering in single-mode optical fibers. This technique is based on strain- and temperature-induced changes in the Brillouin frequency shift. Several approaches for measuring the weak Brillouin line are compared     

Analysis and design-optimization of LCC resonant inverter forhigh-frequency AC distributed power system

The analysis and design of an LCC resonant inverter for a 20 kHz AC distributed power system are presented. Several resonant converter topologies are assessed to determine their suitability for high efficiency power conversion, under resistive and reactive loads. Two LCC-resonant inverter designs were implemented. One with all switches operating with zero voltage switching (ZVS), and another with two switches operating with ZVS and two switches with zero current switching (ZCS). The experimental results are presented along with a performance comparison of the two versions