Deformation and fracture of glass bead/ CTBN-rubber/epoxy composites

Carboxyl-terminated butadiene-acrylonitrile-rubber decreases modulus and yield stress of the studied epoxy but increases fracture toughness. The addition of glass bead compensates for the loss in modulus but has little effect on yield stress. However, it significantly contributes to the fracture toughness by providing additional mechanisms for toughening of both the unmodified and rubber-modified epoxy. For the toughened epoxies studied, fracture surfaces gave only limited information on fracture mechanisms since significant energy absorption also occurs in the material below the fracture surface. Suggestions for suitable material compositions for fiber composite matrices are given.     

An efficient technique for detecting catastrophic convolutional codes

Catastrophic convolutional codes (CC) cause an infinite number of decoded data bit errors when decoding a finite number of code symbols. A CC displays a catastrophic error propagation if the generating polynomials have a common factor. An efficient algorithm for polynomial factorization in GF(2^m) is used for detecting catastrophic CC for any rate n/m and constraint length k. A general formula is derived to calculate the number of catastrophic codes in any (m, n, k) CC.     

Tunable wavelength filters based on nonlinear optical interactionsin semiconductor amplifiers

A novel class of narrow-band tunable wavelength filters is proposed and evaluated. Wavelength selectivity of the proposed filters Is derived from the finite time response of an optical nonlinearity. The nonlinearity is gain saturation in semiconductor optical amplifier structures. The filters are shown to have very narrow passbands tunable over the entire semiconductor gain bandwidth. The key to filter implementation is a device configuration in which the wave-mixing products can be isolated from the amplified inputs. Three integrated optics compatible configurations are considered and shown to have high filter throughputs 34 to 180% and subangstrom bandwidths     

Monitoring systems and determination of actual fatigue usage

At GKN, fatigue monitoring of important components has been conducted since 1979. The monitoring methods depend on the mechanisms of damage; quasi-static loads are regarded as well as dynamic loads. The components were selected for monitoring on the basis of a system analysis. The data resulting from monitoring are used to optimise operation mode steadily. Experience shows that the use of monitoring data as input for fatigue assessment is the most realistic and cost-effective way. This fatigue assessment uses global and local sensitivity studies to evaluate the load-stress relation for each component. These relations can be programmed to produce stress vs. time curves. These are processed according to ASME rules to give a realistic fatigue usage.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Trends in low-cost, high-performance substrate technology

The trends in high density interconnection (HDI) multichip module (MCM) techniques that have the potential to reduce interconnection cost and production time are described. The implementation in laminated dielectric (MCM-L) technology of a workstation processor core illustrates current substrate technology capabilities. The design, routing, layout and thermal management of the processor core are described. Thin-film deposited dielectric (MCM-D) technology is discussed as a cost-effective method for future interconnection applications     

Correlation between serum levels of alanine aminotransferase and ferritin in male blood donors with antibody to hepatitis C virus

Chronic hepatitis C has been demonstrated to be associated with hepatic iron overload, and the hypothesis that the disease activity of hepatitis C is associated with iron cytotoxicity was tested in male volunteer blood donors. Sera with either antibody to hepatitis C virus or hepatitis B surface antigen were selected for determination of ferritin concentration and alanine aminotransferase activity. A correlation between serum ferritin concentration (Y; microgram/l) and alanine aminotransferase activity (X; IU/l) was found in donors with antibody to hepatitis C (log Y = 0.65 x log X + 0.98, r = 0.53, and P < 0.01). The correlation was lower in donors with hepatitis B surface antigen (r = 0.37; P < 0.01). Hepatitis C virus infection probably induces time-dependent iron accumulation associated with the progression of disease activity, while hepatitis B virus infection results in a variety of iron loads with different clinical features. The high disease activity related to hyperferritinemia suggests the presence of iron-induced liver damage in donors with hepatitis C.     

Cervical lymph nodes metastases from a pituitary carcinoma

Ipratropium bromide is a synthetic derivative of atropine with little absorption when used in inhalation, and therefore little secondary effects. The authors review its pharmacological properties and therapeutic efficacy in the treatment of asthma in children. Combined nebulized inhalation of ipratropium bromide and beta 2 sympathomimetic results in a more efficient and more sustained bronchodilatation than beta 2 sympathicomimetic alone in the treatment of acute asthma in children. Ipratropium bromide should be usefully introduced in the therapeutic scheme of acute asthma in children. Further studies will be necessary in order to determine its efficacy and tolerance in infants.