Pulse stabilisation in harmonically FM modelocked erbium fibre ring laser with DFBLD

A new pulse stabilisation scheme for a harmonically frequency modulated (FM) modelocked erbium fibre ring laser using a distributed feedback laser diode (DFBLD) is presented. More than 65 dB supermode noise suppression in the RF spectrum was obtained with the proposed method. Effective reduction of supermode noise can be accomplished as the DFBLD in the fibre laser acts not only as a fast-gain saturated medium but also as an optical bandpass filter for suppressing supermode noise in a harmonically modelocked laser system.     

Design and fabrication of RESURF MOSFETs on 4H-SiC(0001), (112~0), and 6H-SiC(0001)

Design and fabrication of lateral SiC reduced surface field (RESURF) MOSFETs have been investigated. The doping concentration (dose) of the RESURF and lightly doped drain regions has been optimized to reduce the electric field crowding at the drain edge or in the gate oxide by using device simulation. The optimum oxidation condition depends on the polytype: N/sub 2/O oxidation at 1300/spl deg/C seems to be suitable for 4H-SiC, and dry O/sub 2/ oxidation at 1250/spl deg/C for 6H-SiC. The average inversion-channel mobility is 22, 78, and 68 cm/sup 2//Vs for 4H-SiC(0001), (112~0), and 6H-SiC(0001) MOSFETs, respectively. RESURF MOSFETs have been fabricated on 10-/spl mu/m-thick p-type 4H-SiC(0001), (112~0), and 6H-SiC(0001) epilayers with an acceptor concentration of 1/spl times/10/sup 16/ cm/sup -3/. A 6H-SiC(0001) RESURF MOSFET with a 3-/spl mu/m channel length exhibits a high breakdown voltage of 1620 V and an on-resistance of 234 m/spl Omega//spl middot/cm/sup 2/. A 4H-SiC(112~0) RESURF MOSFET shows the characteristics of 1230 V-138 m/spl Omega//spl middot/cm/sup 2/.     

Thermodynamic properties and defect structure of semiconducting compound phases: Tin telluride

Defect equilibria for binary semiconducting compound phases which exhibit ionized native donor and acceptor defects were considered, and equations describing the pressure-temperature-composition relationships for these compound phases were derived. These equations were used to analyze experimental data from the literature for tin telluride. Excellent agreement was obtained between calculated thermodynamic and phase boundary values and experimental data. The approach presented is readily extended to obtain equations for the thermodynamic properties of ternary and higher order semiconducting compound phases.     

Simulation of the initial stages of nucleation and growth of Au/NaCl(100)

The results of a computer simulation of the initial stages of the nucleation and growth of gold on NaCl(100) are presented. A potential energy scaling Monte Carlo model employing a 50 × 50 array, mobile monomers, dimers and trimers, and gold atom vertical “roll up” was used. The parameters in the model were obtained from the work of Robinson and Robins, other published sources and/or found by calculation. Simulations of the migration of single gold adatoms over the surface permitted the determination of the diffusion coefficient as a function of the reciprocal temperature which returned the same activation energy given by the potential field, thus indicating the consistency of the model. Initial cluster densities were determined using deposition rates of R_d = 10¹⁵cm^-2s^-1 and R_d = 10¹⁴cm^-2s^-1 over the temperature range T=200–425 K. Initial cluster growth was found to occur primarily by surface phase transport and resulted in clusters that were shaped like very thin disks. Using the equations from the work of Velfe and coworkers, calculations were made to extrapolate the computer simulation data in order to permit an indirect comparison with the data of Robinson and Robins. Good agreement was achieved. Initial condensation coefficients determined over a 250 ms interval showed that α ≈ 0 at T > 425 K and α ≈ 1 at T < 325 K for a deposition rate of R_d=10¹⁵ cm^-2 s^-1.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

From biological inspiration toward next-generation manipulators: manipulator control focused on human tasks

This paper presents our approach to extend the niche of behavior-based robotics toward manipulation. We use results from neuroscience to derive some qualitative design rules for the mechanics of the manipulator, resulting in a next-generation manipulator, the "soft arm". By defining the basic behaviors of the manipulator as trajectory-producing behaviors (which is also biologically plausible), we have designed a first test case: writing on a board with a mobile manipulator. The soft arm has not yet been developed; therefore, we have emulated such a soft robot arm on an industrial robot.     

Experiments with small V-band waveguide reflector feeds

The radiation patterns of simple rectangular waveguide feeds have been measured at V band. A low-cost test arrangement, operating in the far field but without any absorbers, is shown to give better than 0.5 dB repeatability and more than 30 dB of dynamic range. The general rules of waveguide-feed design for reflector antennas are applicable, but the tendency of narrow feed patterns is somewhat emphasized compared to observations in earlier work at C or X band. For horizontal polarization, the difference is 5 dB at 90/spl deg/ between WR-28 and WR-90 hardware. This is partly caused by an increase in the relative guide material thickness at shorter wavelengths. No clear connection between pattern widths of the two linear polarizations was observed if the guide height was increased, the largest momentary deviation being 3 dB for a rectangular 7.1 by 7.1 millimeter feed. Changes in the guide width had a monotone effect up to 3 dB at 90/spl deg/ offset. Very small feed aperture sizes, around /spl lambda//4 or less, did not show respective widening of 1 dB patterns, although such expected effects were visible at lower amplitude levels.     

Performance comparison of space-time block coded and cyclic delay diversity MC-CDMA systems

Spatial diversity is a widely applied technique for enhancing wireless system performance since it greatly reduces the detrimental effects of multipath fading. Space-time block codes have been considered the best choice for transmit diversity in narrowband environments, but their use in broadband channels is questionable due to their inability to pick up multipath diversity. However, when used in conjunction with an MC-CDMA system, they achieve not only full spatial but also variable multipath diversity depending on the employed spreading. In comparison, cyclic delay diversity is an attractive approach to achieve spatial and multipath diversity. Its simplicity and conformability with current standards makes it desirable for multicarrier systems. Previous studies suggest that CDD is only advantageous with an outer channel code for OFDM systems. In this article, we compare STBCs and CDD applied to an MC-CDMA system in terms of complexity and performance. It is shown that for an MC-CDMA system, CDD benefits from spreading and channel coding that makes it very competitive with STBCs, particularly since it is applicable to any number of transmit antennas with no loss in rate.     

Ecodesigns and applications for noble metal nanoparticles by ultrasound process

Ecodesigns for nano-sized noble metal particles were investigated by a new liquid-solid (metal oxide-alcohol) system. We have reduced noble metal oxides as low-emission starting materials by ultrasound and tried to fabricate various noble metal nanoparticles (Ag, Au, Pt, Pd) at room temperature, Noble metal oxides were investigated during decomposition. These reductions are ecologically clean, because many noble metal oxides are not toxic, and during decomposition, O/sub 2/ is evolved. By choosing suitable conditions, it is reasonable to expect that this simple sonochemical process can be extended to obtain nano-sized metal particles.     

High dielectric constant thin film EBG power/ground network for broad-band suppression of SSN and radiated emissions

We experimentally demonstrated the great advantages of a high dielectric constant thin film electromagnetic bandgap (EBG) power distribution network (PDN) for the suppression of power/ground noises and radiated emissions in high-performance multilayer digital printed circuit boards (PCBs). Five-layer test PCBs were fabricated and their scattering parameters measured. The power plane noise and radiated emissions were measured, investigated and related to the PDN impedance. This successfully demonstrated that the bandgap of the EBG was extended more than three times, covering a range of hundreds of MHz using a 1-cm /spl times/ 1-cm EBG cell, the SSN was reduced from 170 mV to 10 mV and the radiated emission was suppressed by 22 dB because of the high dielectric constant thin film EBG power/ground network.