转炉溅渣护炉改质剂的开发研究

影响转炉溅渣护炉效果的关键因素是终渣成分的控制,采用改质剂对转炉终渣成分进行调整,降低渣中FeO含量和炉渣温度,提高MgO含量和炉渣熔点及粘度,有利于改善炉渣与炉衬的粘结效果,并提高溅渣层的耐蚀性能,缩短溅渣起孕时间,在一定程度上抑制炉渣中铁的氧化物与炉衬中石墨的反应.     

An optical instrumentation using a sensor with a sensordummyagainst noises on sensor and transmission line

This short paper discusses the method of effectively canceling equal status normal mode noise not only on a sensor line but also on a transmission line of an optical instrument using a sensor with a sensordummy resistance     

丙烯腈－苯乙烯共聚物水解磺化产物对泥浆的稳定作用

在实验室条件下对用丙烯腈－苯乙烯共聚物在硫酸存在下的水解磺化产物（ＨＳＡＳ）处理的泥浆性能进行了评定。ＨＳＡＳ处理的泥浆有较小的滤失性，较好的耐盐和抗高温性。     

USERS' TWO-DIMENSIONAL INTEREST AND ITS STORAGE METHOD

The users' interest can be mined from the web cache and can be used widely. The interest can be specialized by the two-tuple (term, weight) in the simple interest model, in which the association relations are not mined, and then the interest cannot be associated in expressing the users' interest. Based on analyzing the WWW cache model, this letter brings forward a two-dimensional interest model and gives the interrelated methods on how to store the two-dimensional interest model effectively.     

游梁式抽油机二次平衡分析

为解决游梁式抽油机能耗大、效率低的问题，设计了二次平衡装置。这种装置通过是挂在抽油机后端的平衡重的平衡作用，降低一次平衡曲柄轴净扭矩的两个峰值，达到减少能耗提高效率的目的。对抽油机的二次平衡作了较详尽的理论分析，给出了实行二次平衡后曲柄轴净扭矩的计算公式和安装二次平衡装置前后曲柄轴净扭矩曲线图。在大庆油田两口井上进行的现场试验结果表明，安装二次平衡装置后，两口井年节约电费分别为0.25万元和1．17万元，经济效益明显。     

真空铸造高强度C/Mg复合材料

本文介绍用真空铸造法制造抗拉强度超过1000MPa的高强度C/Mg复合材料。将T300纤维经C-Si-O梯度涂层处理后单向排布于型腔内,在真空下注入ZM-5合金液,凝固后即得C/Mg复合材料零件或试样。试样的抗拉强度在纤维体积分数为0.35时达1050MPa。本文讨论C-Si-O梯度涂层对获得高强度复合材料的作用。     

HDPE／PS／HDPE－g－PS合金的相容性和力学性能研究

用自制接枝共聚物ＧＲ－Ⅰ、ＧＲ－Ⅱ相容剂研究其对ＨＤＰＥ／ＰＳ共混物相容性和力学性能的影响。通过ＳＥＭ、ＤＭＡ、ＤＳＣ和力学性能测试表征，表明在ＨＤＰＥ／ＰＳ共混中加入这些相容剂其相容性和力学性能有一定提高     

Quantitative analysis of ephedrines in urine by HPLC

Simultaneous determination of six ephedrines in urine sample has been achieved by high performance liquid chromatography on a Lichrospher RP-18 column, using methylamphetamine as internal standard. The 6 ephedrines are well separated in 25 minutes with resolution better than 1.8. This method has high recovery, selectivity and reproducibility, and the linearity is satisfactory from 1.5 micrograms/ml to 25 micrograms/ml with correlation coefficients better than 0.999.     

洗衣机脱水桶注射模设计

通过对洗衣机脱水桶塑料成型件的特性分析,简要介绍了其成型模具的设计和有关参数的计算方法。