High-aspect ratio metal tips attached to atomic force microscopy cantilevers with controlled angle, length, and radius for electrostatic force microscopy

We demonstrate a method to fabricate a high-aspect ratio metal tip attached to microfabricated cantilevers with controlled angle, length, and radius, for use in electrostatic force microscopy. A metal wire, after gluing it into a guiding slot that is cut into the cantilever, is shaped into a long, thin tip using a focused ion beam. The high-aspect ratio results in considerable reduction of the capacitive force between tip body and sample when compared to a metal coated pyramidal tip.     

Design and fabrication of a length-extensional mode rectangular X-cut quartz resonator with zero temperature coefficient.

Rectangular X-cut quartz crystal resonators with cut angles theta > 5.0 degrees and aspect ratios Rzy (= width 2z0/length 2y0) from 0.3 to 0.5 are investigated. The resonators oscillate mode is a length-extensional mode. A semiempirical frequency equation was derived from the stress expressed in terms of the trigonometric and the hyperbolic transcendental functions with constants estimated by the regression curve fit to the stress simulated by the finite-element method (FEM). Contours on which a point satisfies a zero first order temperature coefficient condition are shown in a cut angle theta and Rzy diagram. We proved that a fabricated resonator with Rzy = 0.400 and theta = 16.0 degrees, whose design parameter is located in the area of the contour, had a zero temperature coefficient.     

Grain refinement and superplasticity in a magnesium alloy processed by equal-channel angular pressing

The extrusion/equal channel angular pressing (EX-ECAP) processing procedure, in which magnesium-based alloys are subjected to extrusion followed by ECAP, was applied to a Mg-7.5 pct Al-0.2 pct Zr alloy prepared by casting. Microstructural inspection showed the EX-ECAP process was effective in reducing the grain size from ∼21 μm after extrusion to an as-pressed grain size of ∼0.8 μm. It is shown through static annealing that these ultrafine grains are reasonably stable up to 473 K, but grain growth occurs at higher temperatures. Tensile specimens were cut from the billets prepared by EX-ECAP and testing showed these specimens exhibited superplasticity at relatively low temperatures with maximum elongations up to >700 pct. By processing through EX-ECAP to a higher imposed strain and thereby increasing the area fraction of high-angle boundaries, it is demonstrated that there is a potential for achieving high-strain-rate superplasticity. This article is based on a presentation made at the Symposium entitled “Phase Transformations and Deformation in Magnesium Alloys,” which occurred during the Spring TMS meeting, March 14–18, 2004, in Charlotte, NC, under the auspices of the ASM-MSCTS Phase Transformations Committee.     

Static Coarse Grain Task Scheduling with Cache Optimization Using OpenMP

Effective use of cache memory is getting more important with increasing gap between the processor speed and memory access speed. Also, use of multigrain parallelism is getting more important to improve effective performance beyond the limitation of loop iteration level parallelism. Considering these factors, this paper proposes a coarse grain task static scheduling scheme considering cache optimization. The proposed scheme schedules coarse grain tasks to threads so that shared data among coarse grain tasks can be passed via cache after task and data decomposition considering cache size at compile time. It is implemented on OSCAR Fortran multigrain parallelizing compiler and evaluated on Sun Ultra80 four-processor SMP workstation using Swim and Tomcatv from the SPEC fp 95. As the results, the proposed scheme gives us 4.56 times speedup for Swim and 2.37 times on 4 processors for Tomcatv respectively against the Sun Forte HPC Ver. 6 update 1 loop parallelizing compiler.     

Achieving enhanced ductility in a dilute magnesium alloy through severe plastic deformation

Experiments were conducted to evaluate the utility of a new processing procedure developed for Mg-based alloys in which samples are subjected to a two-step processing route of extrusion followed by equal-channel angular pressing (designated as EX-ECAP). The experiments were conducted using a Mg-0.6 wt pct Zr alloy and, for comparison purposes, samples of pure Mg. It is shown that the potential for successfully using ECAP increases in both materials when adopting the EX-ECAP procedure. For the Mg-Zr alloy, the use of EX-ECAP produces a grain size of ∼1.4 μm when the pressing is undertaken at 573 K. By contrast, using EX-ECAP with pure Mg at 573 K produces a grain size of ∼26 μm. Tensile testing of the Mg-Zr alloy at 523 and 573 K after processing by EX-ECAP revealed the occurrence of significantly enhanced ductilities with maximum elongations of ∼300 to 400 pct.     

Development of dual-probe atomic force microscopy system using optical beam deflection sensors with obliquely incident laser beams

We developed a dual-probe (DP) atomic force microscopy (AFM) system that has two independently controlled probes. The deflection of each cantilever is measured by the optical beam deflection (OBD) method. In order to keep a large space over the two probes for an objective lens with a large numerical aperture, we employed the OBD sensors with obliquely incident laser beams. In this paper, we describe the details of our developed DP-AFM system, including analysis of the sensitivity of the OBD sensor for detection of the cantilever deflection. We also describe a method to eliminate the crosstalk caused by the vertical translation of the cantilever. In addition, we demonstrate simultaneous topographic imaging of a test sample by the two probes and surface potential measurement on an α-sexithiophene (α-6T) thin film by one probe while electrical charges were injected by the other probe.     

Effect of MnOx/TiO2 Oxidation State on Ozone Concentration in a Nonthermal Plasma-Driven Catalysis Reactor

Manganese oxides on titanium dioxide were prepared by impregnation method at various calcination temperatures and by deposition-precipitation method and the catalysts were characterized using TG-DTA, XRD, XPS, and N₂ adsorption. Various oxidation states for manganese were obtained and activity towards ozone decomposition inside a nonthermal plasma catalysis reactor was investigated. Activity tests show that with increasing manganese oxidation state, the greater the degree of ozone decomposition inside the reactor. MnOx/TiO₂ prepared by impregnation method calcined at 350 °C showed the highest decrease in ozone concentration.     

Three-dimensional rainbow schlieren measurements in underexpanded sonic jets from axisymmetric convergent nozzles

The rainbow schlieren deflectometry has been combined with the computed tomography to obtain three-dimensional density fields of shock containing free jets and we call the method the schlieren CT. Experiments on the schlieren CT have been performed at a nozzle pressure ratio of 4.0 by using an axisymmetric convergent nozzle with an inner diameter of 10 mm at the exit where the nozzle was operated at an underexpanded condition. Multidirectional rainbow schlieren pictures of an underexpanded sonic jet can be acquired by rotating the nozzle about its longitudinal axis in equal angular intervals and the three-dimensional density fields are reconstructed by the schlieren CT. The validity of the schlieren CT is verified by a comparison with the density fields reconstructed by the Abel inversion method. As a result, it is found that excellent quantitative agreement is reached between the three-dimensional jet density fields reconstructed from both methods.     

Te concentration dependent photoemission and inverse-photoemission study of FeSe1?xTex

We have characterized the electronic structure of FeSe_1−xTe_x for various x values using soft x-ray photoemission spectroscopy (SXPES), high-resolution photoemission spectroscopy (HRPES) and inverse photoemission spectroscopy (IPES). The SXPES valence band spectral shape shows that the 2 eV feature in FeSe, which was ascribed to the lower Hubbard band in previous theoretical studies, becomes less prominent with increasing x. HRPES exhibits systematic x dependence of the structure near the Fermi level (E_F): its splitting near E_F and filling of the pseudogap in FeSe. IPES shows two features, near E_F and approximately 6 eV above E_F; the former may be related to the Fe 3d states hybridized with chalcogenide p states, while the latter may consist of plane-wave-like and Se d components. In the incident electron energy dependence of IPES, the density of states near E_F for FeSe and FeTe has the Fano lineshape characteristic of resonant behavior. These compounds exhibit different resonance profiles, which may reflect the differences in their electronic structures. By combining the PES and IPES data the on-site Coulomb energy was estimated at 3.5 eV for FeSe.