Unified reliability estimation and management of NoC based chip multiprocessors

We present a new architecture level unified reliability evaluation methodology for chip multiprocessors (CMPs). The proposed reliability estimation (REST) is based on a Monte Carlo algorithm. What distinguishes REST from the previous work is that both the computational and communication components are considered in a unified manner to compute the reliability of the CMP. We utilize REST tool to develop a new dynamic reliability management (DRM) scheme to address time-dependent dielectric breakdown and negative-bias temperature instability aging mechanisms in network-on-chip (NoC) based CMPs. Designed as a control loop, the proposed DRM scheme uses an effective neural network based reliability estimation module. The neural-network predictor is trained using the REST tool. We investigate how system’s lifetime changes when the NoC as the communication unit of the CMP is considered or not during the reliability evaluation process and find that differences can be as high as 60%. Full-system based simulations using a customized GEM5 simulator show that reliability can be improved by up to 52% using the proposed DRM scheme in a best-effort scenario with 2–9% performance penalty (using a user set target lifetime of 7 years) over the case when no DRM is employed.     

Thermal Expansion of Solid Solutions in the ZrTiO4—In2O3—M2O5 (M = Sb, Ta) System

Axial and dilatometric thermal expansions and phase transformations were studied for solid solutions having the α-PbO₂ structure in the ZrTiO₄—In₂O₃—M₂O₅ (M = Sb, Ta) system with nominal formulas of Zr _x Ti _y In _z Sb _z O₄ and Zr _x Ti _y In _z Ta _z O₄ where x + y + 2 z = 2. With increased substitution of z , the cell volume increased, the difference in the b parameters at room temperature between those quenched from 1400° and 1000°C decreased, and the thermal expansion decreased. The axial thermal expansion of ZrTi _y In _z · Ta _z O₄ with z = 0.3 was almost identical with that of HfTiO₄, and those with z = 0.4 and z = 0.45 were smaller than that of HfTiO₄. Unit-cell volumes of these compound were compared with those of single oxides to make it clear that the unit-cell volume of ZrTiO₄ was small anomalously and to distinguish the normal and abnormal substitution systems. These results were explained by the working hypothesis proposed for these compounds.     

Fractionation and enrichment of CLA isomers by selective esterification with Candida rugosa lipase

A commercial product of CLA contains almost equal amounts of cis-9,trans-11 (c9,t11)-CLA and trans-10,cis-12 (t10,c12)-CLA. We attempted to enrich the two isomers by a two-step selective esterification using Candida rugosa lipase that acted on c9,t11-CLA more strongly than on t10,c12-CLA. An FFA mixture containing CLA isomers was esterified with an equimolar amount of lauryl alcohol in a mixture of 20% water and the lipase. When the esterification of total FA reached 50%, two isomers were fractionated in a good yield: t10,c12-CLA was enriched in FFA, and c9,t11-CLA was recovered in lauryl esters. The FFA were esterified again to enrich t10,c12-CLA. At 27.3% esterification of total FA, the t10,c12-CLA content in FFA increased to 64.8 wt% with 89.3% recovery: The ratio of the content of t10,c12-CLA to that of two isomers was 95.9%. Lauryl esters obtained by the single esterification were employed for enrichment of c9,t11-CLA. After the esters were hydrolyzed, the resulting FFA were esterified again with lauryl alcohol. At 62.0% esterification of total FA, the c9,t11-CLA content in lauryl esters increased to 73.3 wt% with 79.4% recovery: The ratio of the content of c9,t11-CLA to that of two isomers was 95.6%. In a 600-g-scale purification, molecular distillation was effective in separating the reaction mixture into lauryl alcohol, FFA, and lauryl ester fractions.     

Preparation of π-conjugated polymers consisting of 2-decylbenzimidazole and thiophene units and chemical properties of the polymers

Polycondensation by Stille coupling of 2-decyl-4,7-dibromobenzimidazoles and N-methyl-2-decyl-4,7-dibromobenzimidazole with 2,5-bis(trimethylstannyl)thiophene and 5,5′-bis(trimethylstannyl)-2,2′-bithiophene gave the corresponding π-conjugated polymers, poly(2-decylbenzimidazole-4,7-diyl-thiophene-2,5-diyl) 1b, poly(2-decylbenzimidazole-4,7-diyl-bithiophene-2,5-diyl) 1c and poly(N-methyl-2-decylbenzimidazole-4,7-diyl-thiophene-2,5-diyl) 2b, in 98-99% yields. The polymers 1b and 2b were fully soluble in CF₃COOH, and partially soluble in DMF (about 60 and 40% for 1b and 2b, respectively) and NMP (about 70 and 40%, respectively). The NMP soluble part of 1b and DMF soluble part of 2b gave values of 0.36 and 0.24 dl g⁻¹ in NMP and DMF, respectively. The DMF soluble part of 1b, 1c and 2b showed absorption peaks at about 458, 465 and 388 nm, respectively, in DMF. In an alkaline medium the absorption peaks of 1b and 1c are shifted to a longer wavelength by 92-101 nm; the observed shifts in the acidic medium and alkaline medium were much larger than those observed with usual benzimidazoles with low molecular weights. Packing structures of 1b, 1c and 2b are discussed based on their XRD patterns.     

Radiation-induced polymerization of ethylene in pilot plant. III. Heavy-phase recycling process

Radiation-induced polymerization of ethylene using aqueous tert-butyl alcohol as medium was carried out in a large-scale pilot plant with a 50-liter central source-type reactor at a pressure of 105 to 395 kg/cm², temperature of 30° to 80°C, mean dose rate of 4.5 × 10⁴ to 1.9 × 10⁵ rads/hr, ethylene feed rate of 5.5 to 23.5 kg/hr, and medium feed rate of 21 to 102 l./hr. The space–time yield and molecular weight of the polymer were in the range of 4.7 to 16.8 g/l.-hr and 1.3 × 10⁴ to 8.9 × 10⁴, respectively. The space–time yield and molecular weight increased with mean residence time at 30°C, whereas at 80°C they became almost independent of the time. The space–time yield increased with pressure and dose rate, slightly decreased with temperature, and was maximum at ethylene molar fraction of 0.5. The polymer molecular weight increased with pressure and ethylene molar fraction, and decreased with dose rate and temperature. The total amount of deposited polymer on the reactor wall, source case wall, and scraping blades was usually less than 1 kg, which was negligibly small for the analysis of polymerization. Continuous discharge of the polymer slurry and production of fine-powder polyethylene were successfully carried out. In the central source-type reactor, a dose rate of 1.9 × 10⁵ rads/hr was obtained with a ⁶⁰Co source of ca. 12 kCi.     

Effect of vanadium and chromium on the microstructural features of V–Cr–Mn–Ni spheroidal carbide cast irons

The objective of this investigation is to study the influence of vanadium（5.0wt%–10.0wt%） and chromium（0–9.0wt%） on the microstructure and hardness of Cr-V-Mn-Ni white cast irons with spheroidal vanadium carbides. The alloys＇ microstructural features are presented and discussed with regard to the distribution of phase elements. The structural constituents of the alloys are spheroidal VC, proeutectoid cementite, ledeburite eutectic, rosette-shaped carbide eutectic（based on M7C3）, pearlite, martensite, and austenite. Their combinations and area fraction（AF） ratios are reported to be influenced by the alloys＇ chemical composition. Spheroidized VC particles are found to be sites for the nucleation of carbide eutectics. Cr and V are shown to substitute each other in the VC and M7C3 carbides, respectively. Chromium alloying leads to the formation of a eutectic（γ-Fe ＋ М7С3）, preventing the appearance of proeutectoid cementite in the structure. Vanadium and chromium are revealed to increase the total carbide fraction and the amount of austenite in the matrix. Cr is observed to play a key role in controlling the metallic matrix microstructure.     

Spatial distribution of silica fillers in phase-separated rubber blends investigated by three-dimensional elemental mapping

The distribution of nano-sized silica in binary rubber blends is characterized by scanning transmission electron microscopy (STEM) tomography combined with energy dispersive X-ray spectrometry (EDX). 3D distribution of silica is visualized by STEM-EDX tomography with the tilt-series of silicon elemental maps, while the phase-separated morphologies of polyisoprene rubber (IR) and styrene-butadiene rubber (SBR) are visualized by STEM-tomography in high-angle-annular-dark field (HAADF) mode. The combination of STEM-EDX and STEM-HAADF tomography enables us to determine the distribution of silica between the two rubber phases quantitatively even with high contents of silica up to 70 phr (weight parts per hundred rubber). It is found that silica is preferentially distributed in the SBR phase, but it is also distributed in the IR phase when the IR fraction in the total rubber components is higher than 40 wt%. The preferential distribution of silica in the SBR phase improves the dispersion of the IR domains. This is the first use of this technique for a multicomponent polymer system, showing the advantage to characterize the complicated multicomponent polymer composite morphologies.     

Development of flexible displays using back‐channel‐etched In–Sn–Zn–O thin‐film transistors and air‐stable inverted organic light‐emitting diodes

We developed flexible displays using back‐channel‐etched In–Sn–Zn–O (ITZO) thin‐film transistors (TFTs) and air‐stable inverted organic light‐emitting diodes (iOLEDs). The TFTs fabricated on a polyimide film exhibited high mobility (32.9 cm²/Vs) and stability by utilization of a solution‐processed organic passivation layer. ITZO was also used as an electron injection layer (EIL) in the iOLEDs instead of conventional air‐sensitive materials. The iOLED with ITZO as an EIL exhibited higher efficiency and a lower driving voltage than that of conventional iOLEDs. Our approach of the simultaneous formation of ITZO film as both of a channel layer in TFTs and of an EIL in iOLEDs offers simple fabrication process.     

Fabrication of 5.8‐in. OTFT‐driven flexible color AMOLED display using dual protection scheme for organic semiconductor patterning

Abstract— A 5.8‐in. wide‐QQVGA flexible color active‐matrix organic light‐emitting‐diode (AMOLED) display consisting of organic thin‐film transistors (OTFTs) and phosphorescent OLEDs was fabricated on a plastic film. To reduce the operating voltage of the OTFTs, Ta₂O₅ with a high dielectric constant was employed as a gate insulator. Pentacene was used for the semiconductor layer of the OTFTs. This layer was patterned by photolithography and dry‐etched using a dual protection layer of poly p‐xylylene and SiO₂ film. Uniform transistor performance was achieved in the OTFT backplane with QQVGA pixels. The RGB emission layers of the pixels were formed by vacuum deposition of phosphorescent small molecules. The resulting display could clearly show color moving images even when it was bent and operated at a low driving voltage (below 15 V).