玻璃微珠的表面化学镀银及红外辐射性能研究

采用化学镀方法在玻璃微珠表面镀银,考察了预处理条件、反应温度和反应时间等因素对玻璃微珠表面镀银的影响,并通过扫描电镜和X-射线衍射分析仪,对镀银后玻璃微珠的表面形貌和结构进行了观察和表征。将镀银玻璃微珠用于涂料中,考察了玻璃微珠在涂料中的应用及其红外辐射率的变化,探讨了化学镀条件对涂料红外辐射率的影响,结果表明,在控制反应温度和浓度的条件下,可使镀银玻璃微珠的红外辐射率由原来的1.02降为0.70,将其应用于涂料后,涂层的红外辐射率为0.80。     

基站智能天线多波束合成技术

采用数字波束形成的技术，给出了基站智能天线多波束合成的有效算法。对圆环阵分布的基站天线多波束方向图进行了综合，得到了空间隔离度很好的多个波束，并将副瓣控制在30dB以下，结果令人满意。该方法可用于任意单元构成的不均匀阵列天线，还可用于波束展宽及扇形波束的合成。     

Gamma-irradiation-induced Ag/SiO2 composite films and their optical absorption properties

Small Ag particles or clusters dispersed mesoporous SiO₂ composite films were prepared by a new method: First the matrix SiO₂ films were prepared by sol-gel process combined with the dip-coating technique, then they were soaked in AgNO₃ solutions followed by irradiation of γ-ray at room temperature and in ambient pressure. The structures of these films were examined by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), and optical absorption spectroscopy. It has been shown that the Ag particles grown within the porous SiO₂ films are very small, and they are isolated and dispersed from each other with very narrow size distributions. With increasing the soaking concentration and an additional annealing, an opposite peakshift effect of the surface plasmon resonance (SPR) was observed in the optical absorption measurements.     

数值试井在白6-2井测试资料分析评价中的应用

数值试井是在近来发展的一项新的试井解释技术，具有处理非均质，复杂边界油气藏问题的优点，弥补了常规解析试井技术的不足。运用数值试井解释技术，结合动、静态资料，通过对白6-1断块白6-2井测试资料的综合分析评价，确定了储层渗流参数，落实了该气藏的边界情况，为该断块下一步开发提供可靠依据。     

硫化氢吸收液的电化学分解条件研究

理想的脱硫工艺应满足体积小、费用低、净化度高、无二次污染等要求。在碱性溶液吸收微量硫化氢时同步进行电解，可有效减小设备体积，并将硫化氢转变为氢气和硫磺，不产生恶性气味。为此，实验研究了温度、浓度、电流密度、pH值等因素对电解阳极过程的影响，确定了适宜的电解条件，并在该条件下进行了吸收实验。结果表明，在最佳电解条件下，硫化钠溶液能充分吸收天然气中经变压吸附提浓的硫化氢（800 mg/m³），吸收率大于99.9％。     

用CMOS工艺实现VSR光电集成接收机的途径

介绍了10Gbit／s速率的甚短距离光传输系统VSR(Very Short Reach)中的接收机。分析了几种有希望用于VSR系统的CMOS工艺兼容的光电探测器。提出用CMOS电路实现VSR光电集成(OEIC)接收机的可能性和实现方法。     

电视电缆故障点的确定

根据惠斯通电桥工作原理，采用回路法可以简便快捷地确定电视地下电缆接地、短路故障点的位置。电容法也是一种常用的检查开路的检测方法。这样维修人员可以迅速排除故障，保证电视节目的正常传送。     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

共面波导有限金属厚度效应的研究

用保角变换法对共面波导金属厚度效应进行了理论分析，编制了相应的计算机程序，给出了数值解，并对此进行了多元曲线拟合，导出了考虑金属厚度后的形状比k、有效介电常数、特征阻抗、损耗的闭定表达式。用此修正表达式求得特征阻抗及损耗的数值解，并与K．C．格普塔的修正值及实验测量值进行了详细比较，结果表明此修正公式与实验值相符较好。