Grain Boundary Sliding in Fatigue of Pure Aluminum

The distributions of plastic strain near grain boundaries induced by fatigue loading were investigatedby the fiducial grid method in pure aluminum specimens, and the resulted grain boundary sliding(GBS) was systematically analysed. The results show that the strain field near a grain boundary isnonuniform. GBS is restricted by the junction of grain boundaries and causes discontinuities of bothdisplacement and strain. A peak value of shear strain was created in short-range area across the grainboundary. GBS plays an important role in cyclic softening and secondary hardening. The control fac-tor of GBS is the relative orientation between two grains and the macro orientation of the grainboundary rather than the ∑ value of the boundary.     

A Special Structure in Al-Mg-Li Alloy (01420) Weld Metal

A large quantity of laminated fine grain zones were observed in the Al-Mg-Li alloy weld metal by manual TIG, which was not found in ordinary Al alloy welds. The fine grain zone is formed because of the Al3(Zr,Ti) particles in the filler metal and the manual filling of filler metal in welding process     

纳米级BaAl_2O_4微粉的制备和性质

分别用溶胶 -凝胶法、低温固相反应法 ,制得了纳米级BaAl2 O4微粉 ,用电镜观察了其形貌和粒径的大小 ,用X-射线衍射仪进行了物相分析 ,测定了其纯度与晶型 ,讨论了制备方法与粒度大小的相互影响     

Microwave Communication to Moving Parts Inside Machines

Cables to moving parts on a linear actuator in production machines, such as pick-and-place machines, are a source of unreliability owing to the possible breaking of a cable. They further reduce the positioning precision of the actuator owing to additional forces. Slotted waveguide systems for rail vehicles based on 2.4 GHz transmission frequency are well known, but transmitters/receivers and waveguides are bulky. The paper reports on the reduction in size of the equipment, adapted to 5.8 GHz using a commercial off-the-shelf RadioLan communication module. Further, the efficient termination of the wave-guide and a new way to reduce standing-wave effects is also discussed.     

异丙苯在Cu-HMS分子筛上的催化氧化

以含Cu的中孔分子筛(Cu-HMS)为催化剂,研究异丙苯的催化氧化。研究发现,Cu-HMS催化剂的加入使异丙苯氧化的诱导期显著缩短。在75℃下,以Cu-HMS为催化剂,O2为氧化剂的纯异丙苯氧化反应,苯乙酮为主要副产物,反应的选择性和转化率都很高。当催化剂用量为1 5×10-4mol/ml时,反应8h后,异丙苯转化率为32 7%,目的产物的累积浓度(质量分数)为37 7%,选择性为99%;反应12h后,异丙苯转化率为42 4%,目的产物的累积浓度为46 3%,选择性为95 6%。     

甲醇氧化羰化制碳酸二甲酯产物气相色谱分析

以Chromosorb 10 1为固定相 ,气相色谱法分析甲醇氧化羰化制碳酸二甲酯产物中水、甲醇、乙酸甲酯和碳酸二甲酯等组份的含量 ,考察了柱温 ,载气流量对分离度的影响 ,确定了适宜的分析条件 ,并用校正面积归一化法定量。该方法操作简便 ,快速 ,精度高 ,重现性好     

基于过程能量综合优化的延迟焦化装置扩大生产能力改造策略

根据延迟焦化流程的特点，分析了延迟焦化装置扩大生产能力的瓶颈，探讨了基于能量综合优化的装置扩能解除瓶颈的策略方法，基于过程能量综合优化，运用流程模拟技术，通过配套的加热炉优化，分馏塔操作优化，换热网络柔性设计等手段，实现了装置扩大生产能力的目的，并运用所提出的策略对某延迟焦化装置进行了基于能量系统优化的扩能改造，在原流程与设备的基础上，装置处理量增大18．2％，装置物耗，能耗大幅度降低，改造设备投资少，说明能量综合优化对工艺装置扩能改造具有重要意义。     

高速往复式内燃机平衡轴低质量设计分析

分析了扇形和偏心圆两种平衡轴设计的要求以及平衡重低质量的设计原则。扇形平衡重半径及宽度应尽量大、夹角应尽量小。偏心圆平衡重的偏心圆半径应尽可能大 ,轴承半径应尽可能小。同样质量的扇形平衡重产生的平衡力比偏心圆平衡重要大。     

分离式热管换热器在脱硫装置的应用

介绍了分离式热管换热器的工作原理及其在工业脱硫装置中的应用，并不其余热回收情况与传统的二次中热方法相比较，阐明了其节能及环保作用。     

悬停直升机的雷达探测技术

首先对直升机旋翼的雷达回波进行建模与分析,在此基础上分析了雷达探测悬停直升机的可能性,提出了一种适用于所有直升机类型的多扫描周期积累检测系统方案,讨论了可能影响其检测性能的因素.