洗衣机脱水桶注射模设计

通过对洗衣机脱水桶塑料成型件的特性分析,简要介绍了其成型模具的设计和有关参数的计算方法。     

自动交换光网络的标准化现状

国际上许多标准化组织都在对自动交换光网络的相关技术和标准规范进行研究。本文介绍了ITU－T、IETF和OIF等几个主要的标准化组织在自动交换光网络标准方面的进展情况。     

Apoptosis and delayed neuronal damage after carbon monoxide poisoning in the rat

Delayed neurological damage after CO hypoxia was studied in rats to determine whether programmed cell death (PCD), in addition to necrosis, is involved in neuronal death. In rats exposed to either air or CO (2500 ppm), microdialysis in brain cortex and hippocampus was performed to determine the extent of glutamate release and hydroxyl radical generation during the exposures. Groups of control and CO-exposed rats also were tested in a radial maze to assess the effects of the CO exposures on learning and memory. At 3, 7, and 21 days after CO exposure brains were perfusion-fixed and hematoxylin-eosin (H&E) was used to assess injury and to select regions for further examination. DNA fragmentation was sought by examining cryosections with the terminal deoxynucleotidyl transferase-mediated dUTP-biotin nick-end labeling (TUNEL) reaction. We found significant increases in glutamate release and .OH generation during and immediately after CO hypoxia. CO-exposed rats showed learning and memory deficits after exposure associated with heterogeneous cell loss in cortex, globus pallidus, and cerebellum. The frontal cortex was affected most seriously; the damage was slight at Day 3, increased at Day 7, and persistent at Day 21 after CO exposure. TUNEL staining was positive at all three time points, and TUNEL-labeled cells were distributed similarly to eosinophilic cells. The number of cells stained by TUNEL was less than by H&E and amounted to 2 to 5% of all cell nuclei in regions of injury. Ultrastructural features of both neuronal necrosis and apoptosis also were observed readily by electron microscopy. These findings indicate that both necrosis and apoptosis (PCD) contribute to CO poisoning-induced brain cell death.     

LDD方法在提高电路工作电压中的应用研究

研究了利用轻掺杂漏结构来制作高电源电压器件的工艺方法。分析了ＬＤＤ结构参数对器件击穿特性的影响，并结合实验结果对Ｎ＾－区的注入剂量，长度及引入的串联电阻进行了优化设计。     

光纤通信在市内接入网的应用

先说明市内接入网的单位用户和住家用户两大类使用通信和电视、交互型和分配型业务的要求不相同，相应地对光纤传输的应用须作不同的考虑，文中认为；光纤从市内交换局直连办公大楼是合乎现实需要的，而对于居民住家，宜选用光纤连至路边或光纤与同轴结合和适当利用无源光网络等方案，俟将来时机成熟才实行光纤连至每一家，文末有概括总结，说明接入网不同于长途网，接入网的光纤系统可以使用常规单模光纤，工作于波长1．3μm，而光放大器和波分多路系统不是普遍需要，但光电子集成在光端机中是必要的。     

NMOS器件两次沟道注入杂质分布和阈电压计算

分别考虑了深浅两次沟道区注入杂质在氧化扩散过程中对表面浓度的贡献。对两次注入杂质的扩散分别提取了扩散系数的氧化增强系数、氧化衰减系数和有效杂地系数，给出了表面浓度与工艺参数之间的模拟关系式，以峰值浓度为强反型条件计算了开启电压，文章还给出了开启电压、氧化条件、不同注入组合之间的关系式。     

地面油管漏失定量测试方法探讨

对油管漏失进行定量测试的方法确定具体漏失位置。方法运用双频道回声探仪探测动液面的原理和工作方法，根据油管漏失形成的死油坏在测试曲线上出现特殊波位置判断油管漏失位置。结果：经过７０多井次的现场试验，该方法具有较高的准确性和可靠性。结论：利用特殊波可以有效监测油管漏失，并具有推广使用价值。     

一种多晶硅高温压力传感器

制作压力传感器时，在二氧化硅层上淀积多晶硅膜，既可利用优良的机械特性，又可保证压敏电阻与衬底间具有良好的绝缘性，由此可大大提高器件的温度特性。介绍了一种多晶硅压力传感器的原理和设计。实验结果表明，这类传感器具有灵敏度好，精度高等特点，电路工作范围为０－２５０℃，且具有良好的温度稳定性。     

抗洪抢险措施及效果

结合“９８”抗洪抢险实例，对多种险情作了具体分析，通过汛后调查，对抗洪抢险消险措施和效果进行了总结，为今后进一步做好防洪消险工作提供了经验。